Atlas Indoor Display
Instruction ManualAcuRite® AtlasTMIndoor Displaymodel 06061
How It Works
AcuRite® AtlasTM is an environmental monitoring station that delivers key information on current outdoor conditions in your exact location. The outdoor device contains sensors that read temperature, humidity, wind speed and direction, rainfall, UV, light intensity, and optionally lightning (requires optional Lightning Detection Sensor; may be purchased separately). These readings are transmitted over a 433 MHz wireless radio frequency (RF) to be received by the AcuRite Atlas indoor touch screen display.NOTE: To view your outdoor readings online from My AcuRite an AcuRite® AccessTM is required; may be purchased separately.
Package Contents
- AcuRite® AtlasTM Indoor HD Display
- AC Power Adapter for Display
- Wall Mounting Bracket (optional)
Set Up Your Indoor Display
1. Plug In Plug in the power adapter. Once the display is powered on, it will help guide you through the next steps.
2. Lift Antenna On the top of the display, lift the antenna for optimal signal reception.
3. Install Batteries In the battery compartment of the AcuRite® AtlasTM outdoor device, install four AA alkaline or lithium batteries. Lithium batteries are recommended in low temperature conditions, especially below -4oF / -20oC.Note: Heavy duty or rechargeable batteries are not recommended.
4. Mount Outdoor Device For more details on outdoor device setup and placement, see the outdoor device instruction manual.
1. Find a suitable place to mount the outdoor device:
- At least 5 feet (1.5 meters) off the ground
- Rear solar panel facing south OR
- Away from heat and humidity sources
- Level for accurate rain reporting
2. Remove rain gauge stabilizer from outdoor device.
5. Set Up Display Follow the on-screen prompts to set the time, date, and units of measurement.
How To Add An Outdoor Device
To view your AcuRite outdoor device readings from an indoor display, the device must be added to the display. Note: This procedure is also required to be completed if you are replacing an outdoor device.1. Verify the outdoor device is powered on.2. From the top-left section of the indoor display, select the Menu icon (
)
3. Select Sensors.Note: If you’re replacing an outdoor device, select Remove A Sensor and remove the batteries and power from the outdoor device that is being replaced.4. Select Add A New Sensor. The indoor display searches for any outdoor devices in wireless range. This may take a couple minutes.5. Once the outdoor device has been located, select Add A Sensor. If more than one outdoor device has been detected, you may need to scroll up and down to select the appropriate device.
Features & Settings
Time And Date Settings
You can set the indoor display’s time and date settings, including the time zone, Daylight Saving Time, and the time and date format.How To Set Time and Date Formats1. From the top-left section, select— the Menu icon ().2. Select Setup.3. From the time and date settingsection, set the settings. Follow the on-screen instructions.4. Select Save.Note: The selected hour determines whether the time is a.m. or p.m.
Unit Of Measurement Settings
You can set the unit of measurement displayed for barometric pressure, temperature, wind direction, wind speed, rainfall, and lightning distance.
How To Change Unit Of Measurement Settings1. From the top-left section, select— the Menu icon ().2. Select Units.3. Select the unit setting(s).4. Select Save.
Display Appearance SettingsYou can set the indoor display’s brightness, contrast and tint levels, backlight dimming and sleep mode, and how often the display rotates between the main screen and records.
How To Change Display Appearance Settings1. From the top-left section, select— the Menu icon ().2. Select Display.3. Adjust the display settings:· Adjust Display set the display’s brightness, contrast and tint levels.· Display Mode set how oftenthe display rotates between the main screen and the records screen.· Backlight set the backlight, auto-dim, and sleep mode settings. 7
Charts & Monthly RecordsThe indoor display stores in its local memory the last 48 hours of readings that are displayed in charts and the monthly reading records.· Charts Available for Indoor and Outdoor Temperature and Humidity, Barometric Pressure, Light Intensity, UV, Wind Speed, Lightning, and Rainfall.· Monthly Reading Records Shows high, low, and accumulation reading records by month.
How To View A 6 Or 48-Hour Reading Chart1. From the main screen, select a reading type.2. From the top-section of the screen, select last 48 hours or last 6 hours.
How To View Monthly Reading Records1. From the top-left section, select the— Menu icon ().2. Select Records > Calendar.3. To change the month displayed, use theleft or right arrow to select a month.
How To Delete Today’s RecordsYou can delete the current day’s readings this feature is commonly accessed when inaccurate readings occur during the setup procedure or due to outdoor device mounting changes.1. From the top-left section, select the Menu— icon ().2. Select Records.3. Select Clear Today’s Records. Today’s recordsfor all reading types are permanently deleted.Save Extended Historical Readings (Optional SD Card)The indoor display stores the last 48 hours of readings in its local memory. If you want to save detailed historical readings, you can automatically log the readings on an SD Card (not supplied).· The indoor display can use an SD Card with up to 32 GB of space.· Readings are saved to the SD Card every 10 seconds.· Calibrations made to readings on the indoor display will also be reflected in readings sent to the SD Card.
ALARMS
Alarms provide a quick and easy way to know when a condition you are monitoring has reached a certain threshold. When a condition set in an alarm is reached, the indoor display activates an alarm notification – including an audible alarm and a flashing alarm indicator on the display.About The Alarm Features· Alarms can be set for temperature, humidity, rainfall, wind speed, time, and forecasted storms.· Set the audible alarm volume or set the volume to off.· Set a single alarm or all alarms to be disabled for those times you do not want to be disturbed.
How To Set An Alarm
1. From the top-left section, select the— Menu icon ().2. Select Alarms.
3. Select Indoor to configure alarmson readings taken by the display.Select Outdoor to configure alarms onreadings taken by the outdoor device.
4. Using the left and right arrows, selectan alarm type > select Next.
5. Set the condition that activates thealarm. When the condition is reached,an alarm notification is activated .
6. Verify the alarm icon is set to ON.
7. Select Save and Exit.
How To Adjust The Alarm Volume1. From the bottom-left of the display, locatethe alarm volume 
icon.2. To adjust the alarm volume, press the alarmvolume icon to the desired level.
To turn off the audible alarm, adjust thelevel until 
is displayed. When set tooff, only the active alarm notification icon flashes as a visual notification that an alarm is active.
How To Silence An Active Alarm1. Push anywhere on screen to clear thecurrent notification. The alarm will trigger again the next time the parameter is reached.
2. Press the button twice to disable the alarm. The alarm press TWO TIMES to turn off alarm will not trigger again unless it is turned back on in Alarm Settings.
How To Disable A Single Alarm1. From the top-left section, select— the Menu icon ().2. Select Alarms.3. Select Indoor to configurealarms on readings taken by the display.Select Outdoor to configure alarms on readings taken by the outdoor device.4. Using the left and right arrows,select the reading type of the alarm to be disabled > select Next.5. Select the alarm iconuntil it displays OFF. OFF
How To Disable All Alarms1. Select Alarms.2. Select Indoor to configurealarms on readings taken by the display.Select Outdoor to configure alarms on readings taken by the outdoor device.3. Using the left and right arrows,select Turn All Alarms Off.4. Select Next. All alarmsare disabled.5. Select Save and exit.
READING CALIBRATIONS
When placement or an environmental factor may impact temperature, humidity, or barometric pressure readings, setting a calibration adjustment can improve accuracy.Note: Calibration adjustments are only applied to readings displayed on the indoor display and stored on the optional SD card. If your outdoor device readings are also sent to My AcuRite, the calibration adjustments set in the indoor display are not sent to My AcuRite or Weather Underground.
How To Set A Reading Calibration1. From the top-left section, select the-= Menu icon ().2. Select Calibrate.3. Select Indoor to adjust readingstaken by the display.Select Outdoor to adjust readings taken by the outdoor device.4. Using the up and down arrows,select the reading type to be calibrated > select next.5. Using the up and down arrows, setan adjustment.6. To save the calibration adjustment,select done.
Specifications for Indoor Display SensorsTEMPERATURE RANGE Indoor : 32ºF to 122ºF; 0ºC to 50ºCHUMIDITY RANGE Indoor : 1-100% RHBAROMETRIC PRESSURE 16 to 32.50 inHgHAVING PROBLEMS? We’re Here to Help.Visit us onlinewww.AcuRite.com
Get more information or download the full AcuRite AtlasTM product manual.
FCC StatementThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1- This device may NOT cause harmful interference, and 2- This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and the receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology.Visit www.AcuRite.com/patents for details.
Limited One (1) Year WarrantyAcuRiteis a whollyownedsubsidiaryof ChaneyInstrumenCt ompanyF. orpurchasesof AcuRiteproductsA. cuRiteprovidesthebenefrts andservicesset forthherein.Forpurchasesof ChaneyproductsC, haneyprovidesthebenefrtsandservicesset forthherein. We warrant that the AcuRite Atlas Environmental Monitoring station premium product we manufacture and cover under this warranty is of good material and workmanship and, when properly installed and operated, will be free of defects for a period of one (1) year from the date of purchase.
The AcuRite Atlas Environmental Monitoring station which, under normal use and service, is proven to breach the warranty contained herein within ONE (1) YEAR from date of sale will, upon examination by us, and at our sole option, be repaired or replaced by us. Transportation costs and charges for returned goods shall be paid for by the purchaser. We hereby disclaim all responsibility for such transportation costs and charges. This warranty does not cover normal wear and tear not affecting the functionality of the product, or products that have been damaged (including by acts of nature), tampered with, abused, improperly installed, or repaired or altered by anyone other than our authorized representatives. Remedy for breach of this warranty is limited to repair or replacement of the defective item(s). If we determine that repair or replacement is not feasible, we may, at our option, refund the amount of the original purchase price (excluding shipping).
THE ABOVE-DESCRIBED WARRANTY IS THE SOLE WARRANTY FOR THE ACURITE ATLAS ENVIRONMENTAL MONITORING STATION PREMIUM PRODUCT AND IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. ALL WARRANTIES OTHER THAN THE EXPRESS WARRANTY SET FORTH HEREIN ARE HEREBY EXPRESSLY DISCLAIMED TO THE EXTENT PERMITTED BY LAW.
We expressly disclaim all liability for special, consequential, or incidental damages, whether arising in tort or by contract from any breach of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. We further disclaim liability from personal injury relating to its products to the extent permitted by law. By acceptance of any of our products, the purchaser assumes allliability for the consequencesarising from their use or misuse. No person,firm or corporation is authorizedto bind us to any other obligation or liability in connection with the sale of our products. Furthermore,no person,firm or corporation is authorized to modify or waive the terms of this warranty unless done in writing and signed by a duly authorized agent of ours. In no case shall our liability for any claim relating to our products, your purchase or your use thereof, exceed the original purchase price paid for the product.
WARRANTY CLAIMS To file a claim against this Limited Warranty,users must 1. Contact AcuRite Support at and provide opportunity for Customer Support to resolve any issue
2. In the event that an issue cannot be resolved over the phone, customer shall send the product(s) in for evaluation to AcuRite at the contact address (see below)
3. Chaney Instrument Service department will repair or replace product as necessary after evaluationThe terms of this Limited Warranty shall be governed in all respects by and construed in accordance with the laws of the State of Wisconsin,USA.without regardto its conflicts of law principles,and exclusivejurisdiction overanycauseof action arising out of this Limited Warranty or your use of the product shall be in the state court located in Walworth County, Wisconsin. You agree to submit to the jurisdiction of such court.
Contact Information If you have questions about this Limited Warranty, please contact us at:AcuRite Attn: Warranty Inquiry 965 Wells St, Lake Geneva, WI 53147
Printed in China 06061 INST 091218
References
[xyz-ips snippet=”download-snippet”]