CheckMate IV RT-U49H+ Universal Remote Control User Manual

CheckMate™ IVModel RT-U49H+Universal Remote Control

Programming & Operating Instructions

To have a clearer idea of the features and capabilities of your remote control, take a moment to carefully read these instructions Save for future reference.

Rev. 9/2001© 2001, CONTEC CORPORATION

1. Introduction

Your CheckMate IV, Model RT-U49H+, universal remote control is simple to program, easy to use, and can operate up to four (4) devices, which include:

CABLE  Cable set-top terminalsTV TelevisionsVIDEO VCR, DVD playersAUDIO Audio-video receivers, amplifiers, CD players, cassette players, DMX / DCR Digital Music converters

Before you can use your remote control, it must be programmed (set-up) to operate the above devices.

2. Before Getting Started

Some of the special features on your remote control are:

Point and PressTM Programming

Lets you program your TV, VIDEO and AUDIO devices without using codes. For more information, see sections 5, 6, 7and 8.

SmartKeys™

Program multiple button presses on the [CABLE], [TV], [BYPASS] and [PPV] buttons. For more information, see section 14.

[DEVICE] Button

Tells which device you are currently operating by illuminating the device’s power button. While the current device is illuminated, press a nonilluminated power button to operate a different device.

[VCR / VOD] Button

“Toggles” the VCR buttons between cable “VideoOn-Demand” (VOD) and VCR / DVD functions.

Memory Guard™

Eliminates reprogramming after battery changes.

Time Out

Shuts remote off if any button is pressed and held for 45 seconds. This extends battery life in the event the remote becomes lodged under or between heavy objects.

Reset

Lets you reset your remote to its original default settings. For more information, see section 17.

3. Installing / Replacing Batteries

Install two (2) “AAA” batteries as indicated by the diagram in the battery compartment.When the illuminated buttons become dim or do not illuminate during use, install two (2) new “AAA” size batteries.Your remote control has Memory Guard™, which eliminates reprogramming after battery changes.

4. Programming Your Cable Set-Top Terminal

Your remote control is pre-programmed to operate Motorola’s DCT® (digital) and CFT2200 (analog) set-top terminals. If you are operating either of these cable set-top terminals, no cable programming is necessary – proceed to section 5.

If you need to operate another cable set-top terminal, look up the brand and model number in the Cable Setup Code list. If you are not sure of your brand and model, contact your cable company.

To program (setup) your cable set-top terminal…

  1. Turn on your cable set-top terminal.
  2. Press [DEVICE], then [MUTE] together – hold both buttons down until the lighted mode buttons start blinking in sequence.
  3. Press [CABLE]. The [CABLE] button lights up.
  4. From the Cable Setup Code list, locate and enter the 3-digit code for your brand and model.
  5. Press [CABLE] to lock in the code. The [CABLE] button will blink and go out.Cable brand & setup code __________________
5. Programming Your TV

If you have a TV that’s operated by remote control, it’s recommended that you plug it directly into a wall outlet instead of the cable set-top terminal.

To program (setup) your TV…

  1. Turn on your TV.
  2. Press [DEVICE], then [MUTE] together – hold both buttons down until the lighted mode buttons start blinking in sequence.
  3. Press [TV]. The [TV] button lights up.
  4.  a. Press and hold [CH ] until your TV turns off.As soon as your TV turns off, release [CH ] ❶.ORb. From the TV Setup Code list, locate and enter the 3-digit code until your TV turns off. If multiple codes are listed, you may have to enter several 3 digit codes until your TV turns off.
  5. Press [MUTE]. If your TV turns back on, press [TV] to lock in the code. The [TV] button will blink and go out.

If your TV doesn’t turn back on, repeat steps 4 and 5 above until you can turn your TV off and on.

TV brand & setup code ______________________

❶ NOTE when using the Point and Press™ Programming method (step 4a.). If you find a code that turns your TV off but not back on, you may have gone past the correct matching code. Try pressing [CH ] one step at a time until you find a code that turns your TV back on.

6. Programming Your VCR or DVD

To program (setup) your VCR or DVD player…

  1. Turn on your VCR or DVD player.
  2. Press [DEVICE], then [MUTE] together – hold both buttons down until the lighted mode buttons start blinking in sequence.
  3. Press [VIDEO]. The [VIDEO] button lights up.
  4. a. Press and hold [CH ] until your VCR or DVD turns off. As soon as your VCR or DVD turns off, release [CH ] ❶.ORb. From the VCR or DVD Setup Code list, locate and enter the 3-digit code until your VCR or DVD player turns off. If multiple codes are listed, you may have to enter several 3-digit codes until your VCR / DVD turns off.
  5. Press [MUTE]. If your VCR or DVD player turns back on, press [VIDEO] to lock in the code. The [VIDEO] button will blink and go out.

If your VCR or DVD doesn’t turn back on, repeat steps 4 and 5 above until you can turn your VCR or DVD off and on.

VCR / DVD brand & setup code ____________

❶ NOTE when using the Point and Press™ Programming method (step 4a.). If you find a code that turns your VCR or DVD off but not back on, you may have gone past the correct matching code. Try pressing [CH ] one step at a time until find a code that turns your VCR or DVD back on.

7. Programming Your TV / VCR Combination
  1. First, program your remote for the TV functions.a. Refer to Section 5 – Programming Your TV.b. Find a TV Setup Code that operates the TV functions (power, vol / , mute, CH  / , 0-9) of your TV / VCR unit.
  2. Then, program your remote for the VCR functions.a. Refer to Section 6 – Programming Your VCR or DVD.b. Enter, lock and test each 3-digit VCR Setup Code until a code is found that operates the VCR functions (play, stop, fast-forward, rewind, pause, record) of your TV / VCR unit.

NOTE: You can not use the Point and Press™ Programming method to program the VCR functions of your TV / VCR unit.

8. Programming Your Audio Device

To program (setup) your audio-video receiver, amplifier, CD player, cassette player or Digital Music converter…

  1. Turn on your Audio device.
  2. Press [DEVICE], then [MUTE] together – hold both buttons down until the lighted mode buttons start blinking in sequence.
  3. Press [AUDIO]. The [AUDIO] button lights up.
  4. a. Press and hold [CH ] until your Audio device turns off. As soon as your Audio device turns off, release [CH ] ❶.ORb. From the Audio Setup Code list below, locate and enter the 3-digit code until your device turns off. If multiple codes are listed, you may have to enter several 3-digit codes until your Audio device turns off.
  5. Press [MUTE]. If your Audio device turns back on, press [AUDIO] to lock in the code. The [AUDIO] button will blink and go out.

If your Audio device doesn’t turn back on, repeat steps 4 and 5 above until you can turn your Audio device off and on.

Audio brand & setup code ___________________

❶ NOTE when using the Point and Press™ Programming method (step 4a.). If you find a code that turns your Audio device off but not back on, you may have gone past the correct matching code. Try pressing [CH ] one-step at a time until find a code that turns your Audio device back on.

9. Operating Your Cable Set-Top Terminal

Your remote control is designed to operate all the features and functions of your cable set-top terminal.

To select your remote’s CABLE mode and operate your cable set-top terminal, press [DEVICE] then [CABLE]. The [CABLE] button will blink and go out. Then press…

[CABLE]                    CABLE on / off.[TV]                            TV on / off.[VIDEO]                     VCR / DVD on / off.[AUDIO]                     AUDIO device on / off.[CH ] / [CH ]       Increases / decreases CABLE channel.[VOL ] / [VOL ]  Increases / decreases TV volume.[MUTE]                Mutes TV volume.[EXIT]                  Exits on-screen menus, view guide.[MENU]               Displays on-screen features, options.[GUIDE]              Displays on-screen listing of programs by date, time, channel.[INFO]                  Displays channel, time information.[PPV] / [LOCK]   Displays pay-per-view events, enter parental control access code[PG ] / [PG ]      Page up / down through menus, view guide.[DAY ] / [DAY ]  Previous / next day in view guide[], [], [], []          Navigate on-screen menus, program guide, PPV events and interactive services.[OK] / [SEL]               Select menu option, program PPV events and function options.[MUSIC] / [ENT]        Selects Music Choice™ digital music through your cable set-top terminal[HELP]                         Displays on-screen help on cable settop terminals so equipped.[FAV]                            Scroll through favorite channels[LAST]                          Displays last channel viewed.

[A], [B], [C]                    Functions set by cable operator.[0] – [9]                           Numeric entry buttons.[BYPASS]                      RF bypass on cable set-top terminal.[VCR / VOD]               Toggles VCR buttons between cable “Video -On-Demand” (VOD) and VCR functions.[HELP] + [LAST]         Cable set-top terminal diagnostic functions (DCT, CFT2200)

In your remote’s CABLE mode, you can also press the blue buttons at the bottom to operate your VCR / DVD’s basic functions or the “VideoOn-demand” (VOD) functions on your cable settop…

[] VOD or VCR / DVD rewind.[] VOD or VCR / DVD play.[] VOD or VCR / DVD fast-forward.[] VOD or VCR / DVD pause.[] VOD or VCR / DVD stop.[] VOD or VCR record.

10. Operating Your TV

Your remote control can operate many functions of your TV.

To select your remote’s TV mode and operate your TV, press [DEVICE] then [TV]. The [TV] button will blink and go out. Then press…

[TV]                TV on / off.[CABLE]        CABLE on / off.[VIDEO]        VCR / DVD on / off.[AUDIO]        AUDIO on / off.[CH ] / [CH]  Increases / decreases TV channels.[VOL] / [VOL] Increases / decreases TV volume.[MUTE]                             Mutes TV volume.[0] – [9]                               Numeric entry buttons.[MENU] or [OK/SEL]     Accesses TV’s on-screen menus.[BYPASS] / [TV/VCR]     Change TV’s video inputs.[LAST]                               View last TV channel[INFO]                               Displays TV channels and time.[EXIT]                               Exits TV’s on-screen menus[PIP]                                   Picture-in-picture on / off.[POS]                                 Picture-in-picture position

[SWAP]                              Picture-in-picture swap.[FRZ]                                 Picture-in-picture freeze.[], [], [], []                  Navigates TV’s menu.[MUSIC] / [ENT]             Pressed after 0-9 to change channels on some TV’s[C]                                     Sleep / timer functions.

In your remote’s TV mode, you can also press the blue buttons at the bottom to operate your VCR / DVD’s basic functions…

[] VCR / DVD rewind.[] VCR / DVD play.[] VCR / DVD fast-forward.[] VCR / DVD pause.[] VCR / DVD stop.[] VCR record.

11. Operating Your VCR or DVD

Your remote control can operate many functions of your VCR or DVD player.

To select your remote’s VIDEO mode and operate your VCR or DVD, press [DEVICE] then [VIDEO]. The [VIDEO] button will blink and go out. Then press…

[VIDEO]           VCR / DVD power on / off.[CABLE]           CABLE on / off.[TV]                   TV on / off.[AUDIO]           AUDIO on / off.[CH] / [CH]    Increases / decreases VCR channels, or DVD skip “+ / –”.[VOL] / [VOL]    Increases / decreases TV volume.[MUTE]                 Mutes TV volume.[0] – [9]                   Enter VCR channels.[BYPASS] / [TV/VCR]     Change VCR’s video inputs.[EXIT]                DVD clear functions.[MENU]             DVD menu functions.[GUIDE]            DVD guide functions.[INFO]               DVD program information.[], [], [], []         Navigate DVD menu.[MUSIC] / [ENT]    DVD enter functions.[A]                            DVD subtitle on / off.[LAST]                      DVD return function.

In your remote’s VIDEO mode, you can also press the blue buttons at the bottom to operate your VCR / DVD’s basic functions…

[] VCR / DVD rewind.[] VCR / DVD play.[] VCR / DVD fast-forward.[] VCR / DVD pause.[] VCR / DVD stop.[] VCR record.

12. Operating Your Audio Device

Your remote control can operate many functions of your audio-video receiver, amplifier, CD player, cassette player or DMX / DCR Digital Music converter.

To select your remote’s AUDIO mode and operate your Audio devices, press [DEVICE] then [AUDIO]. The [AUDIO] button will blink and go out. Then press…

For audio-video receivers, press…

[AUDIO]                     A/V receiver on / off.[VOL ] / [VOL ]   Increases / decreases Audio volume.[MUTE]                      Mutes Audio volume.[CH ] / [CH ]        Next / last preset tuner channel.[1]                      Select “Tuner” input.[2]                      Select “CD” input.[3]                      Select “Tape # 1” input.[4]                      Select “Tape # 2” input.[5]                      Select “Phone” input.[6]                      Select “VCR # 1” input.[7]                      Select “VCR #2” input.[8]                      Select “LD” input.[9]                      Select “AUX” input.[0]                      Select “TV” input.[BYPASS] / [TV/VCR]                      AM / FM on tuner

For CD and cassette players, press…

[]                        CD / cassette rewind[]                         CD / cassette play.[]                        CD / cassette fast-forward.[]                         CD / cassette pause.[]                         CD / cassette stop.[]                         Cassette record.

For DCR and DMX Digital Music Converters, press…

[AUDIO]                     DCR / DMX on / off.[VOL ] / [VOL ]    Increases / decreases volume.[MUTE]                       Mutes volume.[CH ] / [CH ]         Change music selections.[0] – [9]                         Enter selections directly.

13. Programming Volume Control

When you first program your remote, volume / mute are controlled through your TV (except AUDIO volume which defaults to the AUDIO device).

The volume control options in each mode of the remote are:

CABLE                       TV (default), Cable or Audio.TV                               TV (default), Cable or Audio.VIDEO                       TV (default), Cable or Audio.AUDIO                       Audio device (default), Cable or TV.

To control volume / mute through your cable set-top terminal in the remote’s cable mode…

  1. Press [DEVICE], then [MUTE] together – hold both down until the lighted mode buttons start blinking in sequence.
  2. Press [CABLE] to select the cable mode. The [CABLE] button lights up.
  3. Press [VOL ], then [CABLE] for cable volume. The [CABLE] button will blink and go out.

To return volume control back to your TV, repeat steps 1. and 2. above, then press [VOL ], then [TV] in step 3.

14. Your Remote’s SmartKeys™

Your remote has four (4) SmartKeys™ – [CABLE], [TV], [PPV], and [BYPASS] that operate in its cable mode. Each SmartKey™ can be programmed so whenever it’s pressed, it can transmit up to 12 individual button presses in sequence.

Programming and using the [CABLE] SmartKey™

The [CABLE] button normally turns on / off your cable set-top terminal. Here’s an example of how to program the [CABLE] SmartKey™ to turn on (or off) your cable set-top terminal and TV, then tune your TV to its correct output channel, typically 3, with one button press…

  1. Press [DEVICE], then [CABLE] to select the Cable mode of your remote.
  2. Press [CABLE], then [SEL / OK] together – hold both down together until the [CABLE] button lights up.
  3. In this order, press [TV], [0], [3]. The [CABLE] button will blink and remain illuminated.
  4. Press [CH] to lock in this setting. The [CABLE] button will blink and go out.

To return the [CABLE] button to its normal default setting, repeat steps 1 and 2 above, then press [CH].

Programming and using the [TV] SmartKey™

The [TV] button normally turns on / off your TV. Here’s an example of how to program the [TV] SmartKey™ to turn on (or off) your TV, then tune your TV to its correct output channel, typically 3, with one button press…

  1. Press [DEVICE], then [CABLE] to select the Cable mode of your remote.
  2. Press [TV], then [SEL / OK] together – hold both down together until the [TV] button lights up.
  3. In this order, press [0], [3]. The [TV] button will blink and remain illuminated.
  4. Press [CH ] to lock in this setting. The [TV] button will blink and go out.

To return the [TV] button to its normal default setting, repeat steps 1 and 2 above, then press [CH ].

Programming and using the [PPV] SmartKey™ 

The [PPV] button (Cable mode) normally displays your cable system’s listing of pay-per-view events. Here’s an example of how to program the [PPV] SmartKey™ to tune to a specific cable channel (123) with one button press…

  1. Press [DEVICE], then [CABLE] to select the Cable mode of your remote.
  2. Press [PPV], then [SELECT / OK] together – hold both down together until the [CABLE] button lights up.
  3. In this order, press [1], [2], [3]. The [CABLE] button will blink and remain illuminated.
  4. Press [CH ] to lock in this setting. The [CABLE] button will blink and go out.

To return the [PPV] button to its normal default setting, repeat steps 1 and 2 above, then press [CH ].

Programming and using the [BYPASS] SmartKey™

The [BYPASS] button (Cable mode) normally transmits a command that puts your cable set-top terminal in a BYPASS mode. While the cable set-top terminal is in its BYPASS mode, you can record one program on your VCR while watching a different program through your TV. When exiting cable settop terminal’s BYPASS mode, your TV must be retuned to its correct output channel, typically 3, for proper cable reception.

Here’s an example of how to program the [BYPASS] SmartKey™ so whenever it is pressed, it will also tune your TV to its correct output channel, typically 3, for proper cable reception…

  1. Press [DEVICE], then [CABLE] to select the Cable mode of your remote.
  2. Press [BYPASS], then [SELECT / OK] together – hold both down together until the [CABLE] button lights up.
  3. In this order, press [DEVICE], [TV], [0], [3]. The [CABLE] button will blink and remain illuminated.
  4. Press [CH ] to lock in this setting. The [CABLE] button will blink and go out.

To return the [BYPASS] button to its normal default setting, repeat steps 1 and 2 above, then press [CH ].

Remember: When using any SmartKey™ to transmit a series of functions, be sure to keep your remote aimed at the devices to ensure all functions are received in their entirety.

15. Programming a 2nd TV, VCR, DVD

Instead of programming an audio device, you can program your remote to operate a 2nd TV, 2nd VCR, or 2nd DVD player.

To program a 2nd TV to your remote’s [AUDIO] button…

  1. Turn on your 2nd TV.
  2. Press [DEVICE], then [MUTE] together – hold both buttons down until the lighted mode buttons start blinking in sequence.
  3. Press [AUDIO], then [TV]. The [AUDIO] and [TV] buttons will start blinking.
  4.  a. Press and hold [CH ] until your 2nd TV turns off. As soon as your 2nd TV turns off, release [CH ] ❶.OR4. b. From the TV Setup Code list, locate and enter the 3-digit code until your 2nd TV turns off. If multiple codes are listed, you may have to enter several 3-digit codes until your 2nd TV turns off.
  5. Press [MUTE]. If your 2nd TV turns back on, press [AUDIO] to lock in the code. The [AUDIO] button will blink and go out.

If your 2nd TV doesn’t turn back on, repeat steps 4 and 5 above until you can turn your 2nd TV off and on.

❶ NOTE when using the Point and Press™ Programming method (step 4a.). If you find a code that turns your 2nd TV off but not back on, you may have gone past the correct matching code. Try pressing [CH ] one step at a time until find a code that turns your 2nd TV back on.

If you want to program a 2nd VCR or DVD player in the above example, you would press [AUDIO], then [VIDEO] in step 3., then steps 4. and 5. referring to the Video Setup Code list.

16. Code Number Read Back

To identify a 3-digit device code stored under the Point and Press™ method, follow these steps:

  1. Press [DEVICE], then [MUTE] – hold both down until the illuminated mode buttons start blinking in sequence.
  2. Press [CABLE] to identify your cable set-top terminal code. Or [TV], [VIDEO], [AUDIO] to identify these codes. The selected mode button will be illuminated.
  3. Press [INFO]. The illuminated button “blink back” the code numbers, with a 1 second interval between each digit of the code.

Example: For code “035”, the remote will blink 10 times, then 3 times, then 5 times.

17. Resetting Your Remote Control

To reset you remote to its factory default settings…

  1. Press [SELECT / OK], then [LAST] – hold both down together until the [CBL], [TV], [VIDEO], and [AUDIO] buttons blink in sequence two times (approx. 5 seconds).
18. Helpful Tips & Troubleshooting  
  1. Your remote is equipped with a Point and Press™ quick-programming sticker on the back of its case. This will help you quickly program the remote without using codes.
  2. The illuminated mode button will remain on while the remote is in a programming mode. In the absence of an entry, the button will go out after 20 seconds.

When locking in your devices, the illuminated mode button will blink and go out.

3. When using the Point and Press™ programming method, you may find a code that turns your device off but not back on. If this happens…a. the correct code has not been found. Continue pressing [CH ] until your devices turn on and off.b. you may have gone past the correct matching code. Try pressing [CH ] one step at a time until find a code that turns your cable set-top terminal back on.

4. NOTE: If you have a Scientific Atlanta 8500 series cable set-top terminal, press [CH ] or [CH ] to turn on the cable set-top terminal. Press [CABLE] to turn these cable set-top terminals off.

5. When operating a General Instrument model DPBB Cable set-top terminal (Cable Setup Code #101), your remote’s transmitting distance is limited to 20 ft. This is due to receiving limitations of the cable set-top terminal.

6. If you have any questions concerning the operation of your cable set-top terminal, contact your cable operator.

Cable Setup Codes

Manufacturer:               Model:                  Code:MOTOROLA (GI):        DCT, CFT2200:    001CFT2000, CFT2100, WNR: 115JERROLD:                      DL4, DP(V), DQN(V), DPBB: 101OAK / TOCOM             SIGMAONE P1, P2& P3, SIGMA2000, SIGMA 550: 037PIONEER                       VOYAGER: 122BC4100, 4200, 4500, 4600 BA5000, 6000: 034BA-V1000, BA-V2000: 120BA-9000: 121PACE:                               510 Digital: 122PHILIPS:                          Digital: 017SCIENTIFIC-ATLANTA:        EXPLORER: 1228600X: 0028600: 0118540, 8550, 8570, 8580, 8590: 042TOCOM        5503VIP & 5507, 5508: 003ZENITH       MM2500: 008Z-TAC: 108

TV Setup Codes

Admiral 072 081 161 160Akai 001 146Amark 112 143Ampro 073 167 157Amstrad 052Anam 043 056 080 112 131AOC 001 004 058 112Audiovox 076Blaupunkt 088Cairn 201Candel 001 002 003 004Capehart 058Cetronic 043Citizen 001 002 003 004 043 101 103 143Classic 043Concerto 004Contec 043 050 051TV Setup CodesCoronado 143Craig 043Crown 043 143Curtis Mathes 001 004 101 143CXC 043Daewoo 004 016 043 044 076 103 114 125 127 143Daytron 004 143Dwin 177Dynasty 043Dynatech 062Eiki 187Electrohome 024 076 143 196Emerson 001 004 005 028 043 047 048 050 051 076 096 143 151 153 154 155Fisher 007 057Fujitsu 198Funai 028 043Futuretech 043GE 001 004 008 009 034 056 073 074 091 130 144 155 157 160 161 165Goldstar 004 102 106 112 113 116 119 127 143Hall Mark 004Hitachi 004 009 010 011 012 023 072 075 143 158 163 166Infinity 164JBL 164JC Penny 001 004 008 009 024 030 065 101 143 156 160Jensen 013JVC 034 038 070 083 145 199KEC 043Kenwood 001 070Kloss 002 059KMC 143KTV 001 043 143 154Lodgenet 072Logik 072Luxman 044LXI 007 015 052 081 160 164 166Magnavox 001 003 004 022 059 060 061 063 064 094 127 160 164Marantz 001 164Matsui 164Memorex 004 007 072Metz 088MGA 001 004 024 028 042Minerva 088Mitsubishi 004 024 028 040 042 109 124 146 191MTC 001 004 062 101NAD 015 025NEC 001 016 019 024 040 056 130 132 134Nikei 043Onking 043Onwa 043Optonica 019 081Orion 096Panasonic 034 056 080 092 164Philco 001 003 004 024 056 059 060 063 064 164Philips 001 003 004 005 038 059 093 127 164Pioneer 001 018 023 025 116 135 190Portland 004 143Proscan 144 160 161 165 167Proton 004 058 131 143 171 173 193Quasar 034 056 092Radio Shack 004 019 043 127 143RCA 001 004 023 024 056 065 074 144 152 156 160 161 165Realistic 007 019 043 047Roctec 186Runco 073 157 168 169 178 179 180 181 182Sampo 001 004 058 202Samsung 004 050 089 101 105 127 143 160Sanyo 007 020 053 057 082 166 187Scott 004 028 043 048 143Sears 004 007 015 028 030 057 082 094 143 160 165 166Seleco 189 200Sharp 004 014 019 022 028 029 081 143 170 175Siemens 088Signature 072Sony 070 085 126 139 147 185 194Soundesign 003 004 028 043Spectricon 112SSS 004 043Supre Macy 002

Sylvania 001 003 044 059 060 063 064 127 160 164Tandy 081Tatung 056 062Technics 034 080Techwood 004Teknika 002 003 004 024 028 043 072 101 143Telefunken 037 046 086 087Telerent 072Tera 172TMK 004Toshiba 007 015 030 040 062 101 138Totevision 143Universal 008 009Video Concepts 146Vidikron 174 184 188 192Vidtech 004Wards 004 008 009 019 028 034 060 061 063 064 072 074 143 164Westing House 076Yamaha 001 004York 004Yupiteru 043Zenith 072 073 095 103 157Zonda 112

VCR Setup Codes

Aiwa 034 161Akai 016 043 046 124 125 142 146Ampro 072Anam 083Audio Dynamics 012 023 039 043Brocksonic 035 037 129Canon 028 083Capehart 108Craig 001 104 135Curtis Mathes 041 083Daewoo 005 007 010 065 108 110 111 112 117Daytron 108DBX 012 023 039 043Dynatech 034 053Electrohome 059Emerson 006 025 027 029 034 035 036 037 046 083 106 117 129 131 138 153 162

Fisher 001 008 009 010Funai 034GE 063 072 083 107 109 144 147Go Video 104 115 132 136 155Goldstar 012 020 106 114 123Harman/Kardon 012 045Hitachi 018 020 026 034 043 063 150 160Instantreplay 083JCL 083JC Penny 012 020 083 104 106Jensen 043JVC 012 043 048 050 055 060 083 130 150 152Kenwood 014 034 047 048Lloyd 034LXI 001 009 034 106Magin 104Magnavox 034 041 067 068 083 156 164Marnatz 012 067 069 083Marta 106Matsui 027 030MEI 083Memorex 001 010 014 034 053 072 083 104 106 134 139MGA 045 046 059Minolta 020Mitsubishi 020 045 046 049 051 059 061 142 151MTC 034 104Multitech 024 034NEC 012 023 039 043 048Nordmende 043Optonica 053 054Orion 025Panasonic 070 074 083 133 140 145Pentax 020 063 083Philco 034 067 083Philips 034 054 067 071 083 106Pilot 106Pioneer 020 021 048Portland 108Pulsar 072Quartz 002 041Quasar 075 083 145Radio Shack 123RCA 020 034 041 104 107 109 140 144 145 147 158

Realistic 001 008 010 014 034 053 054 083 104 106Rico 058Runco 148Salora 014Samsung 032 083 104 107 109 112 113 115 122 125Sansui 043 048 135Sanyo 001 007 010 014 104 134Scott 037 112 129 131Sears 001 008 009 010 014 020 073 081 106 112Sharp 053 054 083 159 165Shintom 024Signature 034Sony 001 052 053 056 057 058 076 078 083 154Soundesign 034STS 020Sylvania 034 059 067 083Symphonic 034Tandy 010 034Tatung 039 043Teac 034 039 043Technics 070 083Teknika 019 034 083 106Thomas 034TMK 006Toshiba 008 020 042 047 059 079 081 082 112 131Totevision 104 106Unitech 104Vector Research 012Victor 048Video Concepts 012 034 046 141Videosonic 104Wards 001 020 024 034 053 054 083 104 131Yamaha 012 034 039 043Zenith 034 048 056 058 072 080 106

DVD Setup Codes

Apex Digital 220Denon 226 240GE 231 243Harman/Kardon 218 225

JVC 238KLH 223Kenwood 224LG 235 241 247Magnavox 237Marantz 217Mitsubishi 227NAD 221Onkyo 216 233Panasonic 228 234Philips 237Pioneer 229 230Proceed 219Proscan 229 231RCA 231 243Samsung 236 248Sharp 222Sony 232 244Thomson 231 243Toshiba 233 245Yamaha 234 246Zenith 235 241 247

Audio Setup Codes

ADC 007Adcom 057 082 092 161 225Aiwa 018 104 170 188 202 203 211 213Akai 138 189AMC 125 126 127 128 171 174Amend 054Angstrom 142Arcam 141Audio Access 147Audio File 071Audio Matrix 167Audio Technica 134B & K 096 097Bose 070 170 224Carver 006 022 028 029 061 071 077 185 201 214 226Casio 076Cinema Sound 001 134Citation 122 148Clarion 026

Curtis Mathes 076Denon 001 002 011 027 037 109 215 229 230 234Elnlightened Audio 098 099Fisher 047 182 214Fosgate 062 231Goldstar 008Harman/Kardon 003 118 121 132 154 227 231 233Hitachi 020Inkel 222JC Penny 076 216Jensen 058JVC 056 114 149 155 163 191Kenwood 005 026 066 145 146 151 162 181 182 190 192 199 222Koss 216Krell 072Kyocera 007Lexicon 120 180 194Linn 124Luxman 004 009 052 115 137 139 165LXI 076Magnavox 086 152 164 208Marantz 006 025 028 031 040 054 063 185 186Mcintosh 178MCS 076Meridian 012 013 100Mitsubishi 153 204Mondial 042 043 081 112 157 158NAD 113 176 186Nakamichi 103 111 150 172 183Onkyo 017 046 079 080 084 090 107 108 130 179 187 209Optimus 026 041 138Panasonic 032 195Philips 025 034 038 063Pioneer 014 033 035 039 044 045 050 069 078 116 159 168 198Proceed 135 144RCA 010 048 067 117 156Realistic 019 056 073 075 095Rotel 074 083 085Samsung 016Sansui 040 048 065 110 119 228Sanyo 047 059

Scott 019 091Sears 076Sharp 026 094 131 175 181Sherwood 024 030 051 055 102 105 106Sony 015 018 053 064 088 093 101 160 166 184 218Soundesign 036SSI 068Taekwang 138Teac 005 019 049 111 212 217Theta Digital 136Toshiba 060 087 140 198Yamaha 021 023 026 067 089 129 169 173 177 205 232Zenith 143 210

LD Setup Codes

Denon 250 251Funai 245Kenwood 236 249Magnavox 237 246Marantz 252Mitsubishi 246NAD 246Optimus 236 239Panasonic 243Philips 237Pioneer 244 246Radio Shack 245RCA 235Realistic 239Runco 247Sanyo 241Sharp 236 249Sony 240 242Technics 243Theta Digital 237Toshiba 246 249Yamaha 238 248

DCR Setup Codes

DMX-DJ 254Maestro II 255

CheckMate IV RT-U49H Universal Remote Control User Manual – CheckMate IV RT-U49H Universal Remote Control User Manual –

Posted

in

by

admin

Tags:

, ,