USER MANUALSolar Light 180 LED
Please read these instructions carefully before use, to prevent damage to your new LifeGoods product.
- AboutThank you for choosing our LifeGoods product! To en-sure proper and safe functioning of the product please read the manual carefully before use. Please always follow these instructions for safe usage. If you have any questions about the product or experience any pro-blems. please contact us by email: [email protected].
- Package contents1x 180 LED solar lamp1x User Manual2x Screws2x Wall plugs
- Precautions1. During the first use of the product, place the product in a place with sufficient sunlight for charging, the product should be used after being charged for several hours.2. When the product will not be used for a longtime, please place the product in a place with sufficient sunlight The charging time is i day. For maintaining the battery-capacity, comprehensively charge the product in a place with sufficient sunlight for once a month.3. The charging time and charging efficiency of the solar panel may be affected by the weather and the installati-on position. Considering the conversion rate of solar po-wer generation, if the product is used with good weather, it will gain higher charging efficiency and effectiveness.4. When there’s sunlight and other lights. and if the power switch is off, the LED lamp will not be lightened in day and night5. The solar lamp should be installed in the place with suffi-cient light to ensure the solar panel will absorb sunlight sufficiently, so that the working hour of the solar lamp will be prolonged.6. The angle of the solar lamp and the direction of the light should be adjusted to the best position, it is suggested that the best height is 2-3m.7. During winter or when the sunshine duration is short, it is suggested using the solar lamp under mode 1.
- Use method1. For charging the built-in battery, please set the lamp in a position where it can catch sunlight directly2. Strong sunlight can be converted into solar-energy in a more effective way.3. Used in the place where light is required, such as paths, garages and backyards etc, please place the light in the place where it can be easily illuminated by sunlight.
- Specification
Name of product Solar wall lamp Output 5.5V , 2W Battery capacity 2200MAh Angle of the sensor 120 degrees Induction distance 3 – 5 metres Brightness 2000 lumen Quantitiy of LEDs 180 pieces - OperationPosition of the ON/OFF button:
To turn the product on, long press the ON/OFF button for about is. The lamp will now flicker a few times and will be turned on. The default mode is the “Human body induction mode”. Within this mode; the lamp will turn on when people pass by the sensor, and the Lamp will turn off after no movement has been detected by the sensor within 15s.The product has two other settings. To switch in-bet-ween modes please short press the ON/OFF button after switching the product on.Mode 2: Human body interaction + Slight light mode.Press the ON/OFF button shortly once. Mode 2: Human body interaction + Slight light mode. The lamp will turn on when people pass by and the intensity of light will decrease when no movements have been made within 15s.Mode 3: Slight light mode.Press the ON/OFF button shortly twiceThe intensity of the light will be slighter and turn on all the time (no matter if people pass by or not).Note: The lamp will only work if there is no sunlight or other light detected by the solar panels (Even when the ON/OFF button is pressed). During testing, other objects should be used to cover the solar panel, only in this way the lamp will turned on. - Mounting the productNOTES:– Fix the device on a fitted surface with the included screws and plugs.– It is recommended to install the product at a height of 2-3 metres from the ground surface.– You can try other ways to install the product depending on the conditions of the surroundings. Do never put the product upside down, otherwise it will change the effect of solar charging at daylight.
To turn the product on, long press the ON/OFF button for about is. The lamp will now flicker a few times and will be turned on. The default mode is the “Human body induction mode”. Within this mode; the lamp will turn on when people pass by the sensor, and the Lamp will turn off after no movement has been detected by the sensor within 15s.The product has two other settings. To switch in-bet-ween modes please short press the ON/OFF button after switching the product on.Mode 2: Human body interaction + Slight light mode.Press the ON/OFF button shortly once. Mode 2: Human body interaction + Slight light mode. The lamp will turn on when people pass by and the intensity of light will decrease when no movements have been made within 15s.Mode 3: Slight light mode.Press the ON/OFF button shortly twiceThe intensity of the light will be slighter and turn on all the time (no matter if people pass by or not).Note: The lamp will only work if there is no sunlight or other light detected by the solar panels (Even when the ON/OFF button is pressed). During testing, other objects should be used to cover the solar panel, only in this way the lamp will turned on.
NOTES:– Fix the device on a fitted surface with the included screws and plugs.– It is recommended to install the product at a height of 2-3 metres from the ground surface.– You can try other ways to install the product depending on the conditions of the surroundings. Do never put the product upside down, otherwise it will change the effect of solar charging at daylight.[xyz-ips snippet=”download-snippet”]