tp-link 10GBase SFP+ LC Transceiver
To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community.
For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides, welcome to email [email protected].
Install the SFP
1. Wear an ESD-preventive wrist or ankle strap to prevent ESD damage to the transceiver.2. Insert the SFP into the SFP slot and firmly press it into place.
3. Remove the protective dust plug from the SFP.
4. Plug fiber-optic cables into the SFP. Note that the SFP works without any additional configuration.
Remove the SFP
1. Wear an ESD-preventive wrist or ankle strap to prevent ESD damage to the transceiver.2. Disconnect the network fiber-optic cables from the SFP.
3. Pull the safety latch downwards to release the SFP, and then pull it out from the slot.
4. Reinstall the protective dust plug in the SFP’s optical bores and place it on antistatic mat or a static shielding bag.
Note:1. Do not touch the output pins on the transceiver with your hand.2. Always keep the protective dust plug on the SFP’s optical bores until you are ready to make a connection.Caution: DO NOT point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight.
Connection
Only use the same transceiver model between switches for fast and reliable connectivity. For simplicity, we will take TXM431-LR as an example.
Specifications
General Specifications
Environmental and Physical Specifications
TP-Link Compatible Products
- TP-Link Switches with 10G SFP+ Slots
- TX432
Note: The SFP modules may be incompatible with other vendors’ devices. We recommend that you use only TP-Link SFP modules on your TP-Link devices.
FCC compliance information statementProduct Name: 10GBase SFP+ LC TransceiverModel Number: TXM431-LR/TXM431-SRResponsible party:TP-Link USA Corporation, d/b/a TP-Link North America, Inc.Address: 145 South State College Blvd. Suite 400, Brea, CA 92821Website: https://www.tp-link.com/us/Tel: +1 626 333 0234Fax: +1 909 527 6803E-mail: [email protected]This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.Issue Date: 2020/04/15
EU Declaration of ConformityTP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
Safety Information
- Keep the device away from water, fire, humidity or hot environments.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
- Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
- Do not point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight.
Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)
CE Mark WarningThis is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Explanation of the symbols on the product labelNote: The product label can be found at the bottom of the product.
RECYCLING This product bears the selective sorting symbol for Waste electrical 
and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
References
[xyz-ips snippet=”download-snippet”]