PERLESMITH TV Wall Mount Bracket Full Motion Single Articulating Arm Instruction Manual

PERLESMITH TV Wall Mount Bracket Full Motion Single Articulating Arm

WARNING!

WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASSEMBLY. READ FOLLOWING  WARNINGS BEFOREBEGINNING.

  • If you do not understand the instructions or have any concerns or questions, please contact customer service at support[email protected]
  • Do not install or assemble if the parts or hardware is damaged or missing. Not all parts and hardware included will be used. If you require replacement parts, contact customer service at [email protected]
  • This product may contain moving parts. Use with caution.
  • DO NOT INSTALL INTO DRYWALL ALONE.
  • Please check www.perlesmith.com for more products and company information.

Tools Needed (Not Included)

Supplied Hardware

Hardware （Wall /Product)

Lag Bolts M6X60

Washers Ø6mm

Level

CAUTION!

These anchors are for concrete or brick walls ONLY. DO NOT use them in drywall or wood studs.
TV Screws / Washers

WashersØ6mmM4-5-6

SpacersL10mm

 

Spacers L5mm

 

Philips ScrewsM6 x 15mmM6 x 30mm

 

Philips ScrewsM8 x 15mmM8 x 45mm

 

Philips ScrewsM4 x 30mm

 

 

STEP 1

Measure the distance between the holes located at the back of your TV (these measures may form the shape of a square, or a rectangle) and check that these taken measures are within the VESA(*) range for this wall mount. (*) VESA: International standard established by the TV manufacturers used to determine if LCD / LED TVs are compatible with wall mounts.
Check TV screws

Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M4, M6, or M8) to use.
When attaching brackets to the flat screen. Be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes.  

 

STEP 2

For Flat screen TV

 For Curved TV

 

STEP 3A For Wood Stud Installation

WARNING:Avoid potential personal injury or property damage! All lag bolts [A1] MUST BE firmly tightened to prevent unwanted movement of the wall plate.WARNING:

  • Drywall covering the wall must not exceed 5/8 in. (16 mm)
  • Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½ in. (38 x 89 mm)
  • Stud center must be verified
3A-1

Use a stud finder (not included) to locate wood stud Mark the edge and center locations
3A-2
3A-3

Drill 3 pilot holes using a Vs in.(3mm) diameter drill bit. Make sure the depth is not less than 2.36 in. (60mm).
3A-4

Mount the wall plate using 3 sets of M6 lag bolts A1 and washers A2 with a socket wrench (not included).

 

STEP 3B For Concrete Wall Installation

WARNINGAvoid potential personal injury or property damage! All lag bolts [A1] MUST BE firmly tightened to prevent unwanted movement of the wall plate. WARNING:  

  • Mount the arm assembly/wall plate directly onto the concrete surface
  • Minimum solid concrete thickness: 203 mm (8 in.)
  • Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
3B-1

Position the wall plate at your desired height, level the wall plate and mark the pilot hole locations.
3B-2

Drill 4 pilot holes using a 25/64 in. (10mm) diameter drill bit. Make sure the depth is not less than 2.56 in.(65mm).
3B-3

Install wall plate using lag bolts A1, washers A2 and anchors A3. Tighten the lag bolts until they are pulled firmly against the wall plate.

 

STEP 4 Hang the TV onto the wall plate

 

 

Step 5 Level Adjustment

If needed, the TV can be leveled +/-3 degrees

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,