Narcissus Electric Knife Sharpener User Manual

Table of Contents

Please read this manual in detail before the first use.

Follow the steps below to sharpen the knife:

Put the knife into the sharpening groove to make the blade touches the rotating grinding wheel.
Pull back slowly until the blade all pass through the grinding wheel.
Repeat steps ①② for 3 times.
Change the knife to the neighboring sharpening groove.
Repeat steps ①②③ to sharpen another side of the blade.
Repeat steps ①②③④⑤ until the knife becomes sharp enough.

Tips

The sharpener has 2 different grinding wheels. The left wheel is rough, suitable for grinding blunt knives. The right wheel is smooth and suitable for grinding sharp knives.
Each sharpening groove has two sides. Place the knife obliquely against the inclined side to get a better sharpening effect.
Turn on the sharpener first. Then put knives into the sharpening groove to avoid damage to knives.
DO NOT push knives forward when sharpening to avoid damage to knives.
DO NOT press down hard on knives when sharpening to avoid damage to knives.
The sharpener is not suitable for grinding curved, thick, zigzag kinves.
The sharpener CANNOT work continuously for more than 5 minutes for its overheat-protection device. Please wait patiently for 15 minutes before resuming use it.
The sharpener sometimes sends a smell, this is normal, please rest assured to use.

Move one blade of the scissors slowly to touch the rotating scissors grinding wheel.
Pull the scissors against the grinding wheel slowly.
Repeat steps ①② for 3 times.
Follow steps ①②③ to grind another blade of the scissors.
Repeat steps ①②③④ until the scissors are sharp enough.

Tips: The sharpener cannot fully repair the scissors with unstable rivets. Because it can do nothing about the loose rivets.

Insert the screwdriver into the grinding hole slowly until it touches the rotating grinding wheel.
Push the screwdriver inward slowly until its front end becomes smooth enough.

Tips:

Use the sharpener with the speciﬁc voltage 120V~60Hz.
Remove the grease and water from knives before sharpening.
DO NOT add water, oil or other substances when sharpening knives to avoid danger.
The sharpener is not suitable for grinding curved, thick, zigzag tools.
DO NOT allow water to ﬂow into the sharpener to avoid damage.
In case the grinding wheel is stopped by knives, remove knives immediately to avoid damage to the sharpener
Avoid using or touching by children to avoid accidents.
The sharpener must be placed in a dry area and away from high temperatures.
Do not replace the wire without authorization. Unplug the wire immediately if there is any problem, and contact Narcissus.

Each wheel can grind about 100 knives. If the surface of the wheel is serious, we recommend that you replace the wheel in the following steps:

Unplug the power supply of the sharpener. Put the bottom up on the table.
Remove the 4 foot pads at the bottom. Unscrew the 4 screws in the foot pad holes.
Open the shell and use two wrenches to loosen the nuts on both ends of the shaft.
Remove the old grinding wheel and replace it with a new one. Be careful not to lose small parts.
Check that all components are installed correctly, and then install nuts on both ends of the shaft.
Install the plastic cover, screws and foot pads in order.
Enjoy your new sharpener!

Clean up debris after each use to avoid damage to the sharpener. Attention: Unplug the power plug before cleaning.
Unplug before cleaning.
Wipe the surface with a clean soft cloth.
DO NOT immerse the sharpener in water for cleaning.
Store the sharpener in a dry and ventilated place.

Thanks for selecting and supporting Narcissus.

Narcissus provides all customers free 12 months of product-replacement services.

If there is any quality problem, please send emails to to contact us. We will provide you with a satisfying solution.

Thank you for understanding!

[xyz-ips snippet=”download-snippet”]

Posted

2023-01-19

admin

Tags: