ULINE H-6431 LED Strip Light Instructions

Table of Contents

ULINE H-6431 LED Strip Light

TOOLS NEEDED

Electric Drill	1/16″ Drill Bit	Flat Head Screwdriver
Pliers	Hammer	Wire Stripper

SAFETY INSTRUCTIONS

To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings and instructions included with and on the fixture box and all fixture labels.
Before installing, servicing or performing routine maintenance on this equipment, follow these general precautions.
Installation and service of luminaires should be performed by a qualified, licensed electrician.
Maintenance of luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.
It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output that is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/ lens and clean in above manner, replacing damaged gaskets as necessary.
DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov
These instructions do not cover all details or variations in equipment, nor provide every possible contingency to meet in connection with installation, operation or maintenance. Should further information be desired or should particular problems arise that are not covered sufficiently for the purchaser’s or owner’s purposes, contact Uline Customer Service. WARNING! To prevent risk of electric shock or burn:
Disconnect or turn off power before installation or servicing.
Verify that supply voltage is correct by comparing it with the luminaire label information.
Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
All wiring connections should be capped with UL approved and recognized wire connectors.
Allow lamp/fixture to cool before handling. Do not touch enclosure or light source.
Do not exceed maximum wattage marked on luminaire label.
Follow all manufacturer’s warnings, recommendations and restrictions for driver type, burning position, mounting locations/methods, replacement and recycling.CAUTION! To prevent risk of fire or injury:
Wear safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.• Avoid direct eye exposure to the light source while it is on.• Keep combustible and other materials that can burn away from lamp/lens.• Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying. CAUTION! To prevent risk of product damage:• Never connect components under load.• Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
Unless individual product specifications deem otherwise, never connect an LED product directly to a dimmer packs, occupancy sensors, timing devices or other related control devices. LED fixtures must be powered directly off a switched circuit.
Unless individual product specifications deem otherwise, do not restrict fixture ventilation. Allow for some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam or other material that will prevent convection or conduction cooling
Unless individual product specifications deem otherwise, do not exceed fixtures maximum ambient temperature.
Only use fixture in its intended location.
LED products are polarity sensitive. Ensure proper polarity before installation.
Electrostatic Discharge (ESD) – ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit.
Do not touch individual electrical components, as this can cause ESD, shorten lamp life or alter performance.
Some components inside the fixture may not be serviceable. In the unlikely event your unit requires service, stop using the unit immediately and contact Uline Customer Service.
Always read the fixture’s complete installation instructions prior to installation for any additional fixture-specific warnings.NOTE: Please see product-specific installation instructions for additional warnings or any applicable FCC or other regulatory statements. NOTE: Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please contact Uline Customer Service

* Acuity Brands Lighting, Inc. and Uline assume no responsibility for claims arising out of improper or careless installation or handling of products.

PARTS

#	DESCRIPTION	QTY
1	Fixture Housing	1
2	Wireway Cover	1
3	Lamp	1
4	Ballast	1

ASSEMBLY

Remove fixture components. Check that all parts are included. (See Parts section on page 2)NOTE: Turn off power at circuit breaker.
Remove wireway cover (2) by lifting upward on exposed edges of part. Start in the middle and work outward.
Determine appropriate knockout for removal in relationship to incoming power supply. (Knockouts are located on each end and back of the fixture.)a. To remove knockouts: Place standard screwdriver on edge of circle (on opposite side from retaining tabs) and gently strike with hammer. Grip edge with pliers and flex back and forth until removed. (See Figure 1)
If using Romex strain relief bushing, install the bushing into the open hole.
Position the fixture housing (1) against the mounting surface. With a pencil, mark the screw hole locations to be located at the narrow section of the key-holes. (See Figure 2)
Insert house power supply cable through open hole or strain relief bushing.
Using a drill with a 1/16″ drill bit, make two small pilot holes at the marked screw hole locations. If drill bit does not encounter a stud or wood surface, use toggle bolts or suitable fastener depending on structural conditions. If drill bit does encounter wood surface, use #10 wood screw.
Partially install the mounting screws. Position the fixture housing against the mounting surface with the screw heads through the keyhole mounting holes. Slide the fixture until the screw heads are through the narrow section of the key holes. Finish tightening the screws to secure the fixture against the mounting surface.CAUTION! Connect fixture to supply house wires rated for at least 194°F. Do not use fixture on dimming circuits.
Cut supply cable to desired length. Strip black and white wire leads with wire strippers to expose 3/8″-7/16″ of bare metal. (See Figure 3)
Connect supply (house) wires to fixture wires – white to white, black to black and green to green or bare copper ground wire.
Bundle wires in tight grouping to be out of the way and reinstall wireway cover.

1-800-295-5510www.uline.com

References

[xyz-ips snippet=”download-snippet”]

Posted

2023-01-20

ULINE

admin

Tags:

H-6431, LED Strip Light, ULINE