NINJA CREAMi Blender User Guide

NINJA CREAMi Blender

SCAN & WATCH HOW IT WORKS qr.ninjakitchen.com/creami-ca

 Assembly & Process

1. Plug in unit first The unit will NOT run if the outer bowl is installed before the unit is plugged in.
2. Install CREAMi™ Pint Remove lid from pint and check that the ingredients have not been frozen at an angle. Place the pint containing the frozen base in the outer bow
3. Install Creamerizer™ Paddle Push the paddle into the underside of the outer bowl lid.
4. Install lid Position the tab of the lid just slightly to the right of the outer bowl handle so the lines on the lid and handle align. Rotate the lid clockwise to lock.NOTE:If programs will not illuminate, make sure the unit is properly assembled.See the troubleshooting section of the safety instructions if install light is illuminated.
5. Install outer bowl After plugging in the unit, place the outer bowl on the base with the handle in the middle of the unit. Twist handle to the right to raise the platform and lock the bowl in place. You should hear a click.
6. Select program Press the power button, then select the program that suits your recipe.
7. Remove bowl When program ends, hold the release button on the left of the motor base and twist bowl handle clockwise to remove.
8. Remove lid Press the lid unlock button and twist to remove lid.
9. If adding mix-ins, use a spoon to create a 4 cm wide hole that reaches the bottom of the pint. Add chopped or broken mix-ins to the hole in the pint and process again using the MIX-IN program.– OR –If not adding mix-ins, RE-SPIN can be used on a crumbly or powdery pint to make it creamy. RE-SPIN is often needed for very cold bases.DO NOT RE-SPIN before using MIX-IN program.

Perfectly personalized ice cream

PREP: 5 minutes | FREEZE: 24 hours | PROGRAM TIME: 1^1/2 minutes | MAKES: 4 servings

INGREDIENTS

• 1 tablespoon (18 g) cream cheese
• 70 g granulated sugar
• 180 ml heavy cream
• Flavoring, 1 teaspoon extract of your choice OR 2 tablespoons of cocoa powder
• 240 ml whole milk
• 40 g of your favorite mix-ins (optional)

PICK YOUR FLAVOR

• Microwave the cream cheese for 10 seconds.Add sugar and flavor, then whisk the mixture until it looks like frosting.
• Slowly mix in heavy cream and milk until sugar is dissolved.
• Pour base into CREAMi™ Pint. Place lid on pint and freeze for 24 hours.
• Remove lid from frozen pint.Refer to next page for Assembly & Process instructions.Select ICE CREAM.

PICK YOUR MIX-INS TO ADD A PERSONAL TOUCH

^1/4  cup of your favorite crushed candies, frozen fruits, chopped nuts, chocolate pieces, and more.

With a spoon, create a 4 cm wide hole that reaches the bottom of the pint.Add mix-ins to the hole in the pint and process again using the MIX-IN program.

Disassembly & Cleaning

Remove pint & paddleLift the pint out of the outer bowl.Rinse the outer bowl lid to remove any sticky residue or pieces wedged in the paddle.Then remove the paddle by pressing the paddle latch on top of the lid.All parts are dishwasher safe (top rack only) and can also be hand-washed.

Outer bowl lidlocks Creamerizer Paddle in place.

Creamerizer™ PaddleThis dual functioning paddle finely shaves and mixes frozen ingredients into the creamiest treats.

CREAMi™ Pints & LidsBPA-free pints and lids for making and storing CREAMi treats.

Outer bowlsecurely holds the pint in place during processing.

More pints, more CREAMi treats.Receive a coupon for additional CREAMi Pintswhen you register your Ninja CREAMi purchase. To register your product and claim your reward, scan the code below or visit qr.ninjakitchen.com/creami-ca

© 2021 SharkNinja Operating LLC.CREAMERIZER, CREAMI, and NINJA are trademarks of SharkNinja Operating LLC.NC301C_QSG_E_MP_Mv6

References

• 
  qr.ninjakitchen.com/creami-ca
• 
  qr.ninjakitchen.com/