BUFFALO DA564/DA565/DA566/DA567 Hot Dog Warmer Instruction Manual

Table of Contents

Hot DogWarmerInstruction manual

Model :DA564/DA565/DA566/DA567

Safety Tips

Position on a flat, stable surface.
A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.
Consult Local and National Standards to comply with the following:– Health and Safety at Work Legislation– BS EN Codes of Practice– Fire Precautions– IEE Wiring Regulations– Building Regulations
DO NOT immerse the appliance in water.
DO NOT clean with jet/pressure washers.
DO NOT move or carry the appliance when it is switched on.
DO NOT operate the appliance without water in the water dish.
Suitable for indoor use only.
Always switch off and disconnect the power supply to the appliance when not in use.
Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities.
If the power cord is damaged, it must be replaced by a BUFFALO agent or a recommended qualified technician in order to avoid a hazard.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Caution! Hot surface!
BUFFALO recommends that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to: Visual Inspection, Polarity Test, Earth Continuity, Insulation Continuity, and Functional Testing.
BUFFALO recommends that this product is connected to a circuit protected by an appropriate RCD (Residual Current Device).

Introduction

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your BUFFALO product.Product Description

DA564 – Hot Dog Warmer
DA565 – Hot Dog Warmer with 2 pins
DA566 – Hot Dog Warmer with 4 pins
DA567 – Hot Dog Warmer with 6 pins

Pack ContentsThe following is included:

Hot Dog Warmer
Glass Warmer Jar & Lid
Instruction manual
Hot Dog Basket
Water Dish

BUFFALO prides itself on quality and service, ensuring that at the time of packaging the contents are supplied fully functional and free of damage.Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately.

Installation

Remove all packaging, taking care to dispose of all polythene bags safely.
Check the product for any transit damage, do not use if there is damage to the product or accessories.
Wipe bread roll spikes to remove any transit or manufacturing residues.
Wash the glass jar, lid, hot dog basket, and water dish, in warm soapy water, then dry thoroughly.
Insert Water Dish into the Hot Dog Warmer body and then add water above the MIN fill indicator (200ML) or to a capacity of 80% of the Dish.
Place the Glass Jar over the Water Dish, place the Hot Dog Basket into the Glass Jar and fit Lid to the Jar.

Control panel

Operation

Fill Basket with Hot Dogs, place the basket in the jar, and put the lid on the jar.
Connect the appliance to the mains power supply.
Turn on the ON/OFF switch for the water dish.
Set the temperature control knob to the desired setting. The appliance begins to heat up.
When water is being heated, the indicator light will come on until the set temperature is reached, then the indicator light will go out. The power/heating element will come back on when the temperature of the water drops, the indicator light will come on and heating will continue until the set temperature is reached again.
Remove hot dogs from the jar as required.
Bread rolls can be warmed on the pins. Carefully push the roll down onto the pin then turn on the corresponding/OFF switch to warm.

Thermal Protection Reset Button

This appliance is fitted with thermal protection device to protect the unit from damage due to overheating, low water, etc. The RESET BUTTON is located on the rear of the unit.
If the unit overheats, allow cooling then reset by removing the cover and pressing the button.

Cleaning, Care & Maintenance

• Before cleaning takes place, the Warmer should be disconnected from the electricity supply by removing the plug from the socket.• Do not attempt to clean the warmer or parts until they have completely cooled.• Water Dish, Glass Jar, and Lid should be washed in soapy water, then thoroughly rinsed after every session of use.• Other areas of the Warmer should be wiped down with a clean, damp cloth, or using a food-safe antibacterial cleaner.

Troubleshooting

Fault	Probable Cause	Solution
Indicator Light does not come on & Warmer does not heat up	The unit is not switched on	Check the unit is plugged in correctly and switched on
Plug or lead is damaged	Call BUFFALO agent or qualified Technician
Fuse in the plug has blown	Replace the plug fuse
Power supply	Check power supply
Thermal Protector has activated	Reset Thermal Protector
Indicator Light comes on but Warmer does not heat up	The heating element has failed	Call BUFFALO agent or qualified technician
Thermostat has failed	Call BUFFALO agent or qualified technician
Water Dish requires filling as all water has evaporated	Add water to Dish

Technical Specifications

Model	Voltage	Power	Current	Dimensions hxwxdmm	Weight
DA564	220-240V—,50/60Hz	450W	1.9A	370 x 340 x 340	5.5Kg
DA565	220-240V—,50/60Hz	550W	2.4A	370 x 410 x 340	7kg
DA566	220-240V—50/60Hz	650W	2.8A	370 x 550 x 340	9kg
DA567	220-240V—,50/60Hz	750W	3.2A	370 x 670 x 340	11kg

Electrical Wiring

This appliance is supplied with a 3 pin BS1363 plug and lead.The plug is to be connected to a suitable mains socket.This appliance is wired as follows:

Live wire (colored brown) to the terminal marked L
Neutral wire (colored blue) to the terminal marked N
Earth wire (colored green/yellow) to terminal marked E

This appliance must be earthed.If in doubt consult a qualified electrician.Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required, they must be readily accessible.

Compliance

The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.BUFFALO products have been approved to carry the following symbol:

All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of BUFFALO.Every effort is made to ensure all details are correct at the time of going to press, however, BUFFALO reserve the right to change specifications without notice.

DECLARATION OF CONFORMITY

Conformiteitsverklaring

Equipment Type	Model
Hotdog warmerHotdog warmer with 2 pinsHotdog warmer with 4 pinsHotdog warmer with 6 pins	DA564 (& -E)DA565 (& -E)DA566 (& -E)DA567 (& -E)
Application of Territory Legislation & Council Directives(s)	Low Voltage Directive (LVD) – 2014/35/EUElectrical Equipment (Safety) Regulations 2016EN 60335-1:2012 +A11:2014EN 60335-2-48:2003 +A1:2008 +A11:2012EN 62233:2008Electro-Magnetic Compatibility (EMC) Directive 2014/30/EU – recast of 2004/108/ECElectromagnetic Compatibility Regulations 2016 (S.I. 2016/1091)EN 55014-1:2017EN 55014-2:2015EN 61000-3-2:2014EN 61000-3-3:2013Restriction of Hazardous Substances Directive (RoHS) 2015/863 amending Annex II to Directive 2011/65/EURestriction of the Use of Certain Hazardous Substances in Electrical and ElectronicEquipment Regulations 2012 (S.I. 2012/3032)
Producer Name	Buffalo

I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s) and Standard(s).

Date	20th May 2021
Signature
Full Name	Ashley Hooper	Eoghan Donnellan
Position	Technical & Quality Manager	Commercial Manager/ Importer
Producer Address	Fourth Way, Avonmouth, Bristol, BS11 8TBUnited Kingdom	42 North Point Business Park New Mallow RoadCork Ireland