HOME INTELLIGENCE
OPERATINGMANUAL
4 x BEEP & RED LED BLINKING MOVE O FRESH AIR!
FIBARO CO SENSORFGBHCD-001
Important safety information
Read this manual before attempting to install the device!Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer, Fibar Group S.A. will not be held responsible for any loss or damage resulting from not following the instructions of the operating manual.
General carbon monoxide informationCarbon monoxide (CO) is a colorless, odorless, and tasteless poison gas that can be fatal when inhaled. It is produced when liquid, solid, or gas fuel is burned.Symptoms of carbon monoxide poisoning
The early symptoms of carbon monoxide poisoning can be confused with flu-like symptoms: headache, dizziness, and nausea. Breathing carbon monoxide causes these symptoms even in healthy people. It can also cause sleepiness, vision problems (including blurred vision), ringing in the ears, aching arms, and legs, irregular breathing, fatigue, and confusion. At very high levels, it causes loss of consciousness and death. Some external factors, eg. exposure to the high concentration of basic (non-acidic) gases, silicone vapors, hydrogen sulfide or sulfuric acid gas, organic vapors, contact with water, dust, and oil mist, or dew condensation may affect the reliability of the device operation. This device may not protect from long-term exposure to low levels of carbon monoxide which can also lead to neurological symptoms.The device is not a substitute for appropriate ventilation and exhaust systems.
HomeKit technologyApple HomeKit technology provides an easy, secure way to control HomeKit-enabled accessories using Siri on your iPhone, iPad, or iPod touch.
After installing your FIBARO CO Sensor, configure it from a compatible app with just a few simple steps.You can even create your own custom scenes to control your home settings. For example, you can create a scene to automatically turn off the lights, lock your doors, close the garage door, and set the thermostat to the desired temperature in just one step.
Controlling this HomeKit-enabled accessory requires an iPhone, iPad, or iPod touch with iOS 9.3 or later.Controlling this HomeKit-enabled accessory away from home requires a third-generation Apple TV with Apple TV software 7.2.1 or later or a fourth-generation Apple TV with tvOS 9.2 or later and an iPhone, iPad, or iPod touch with iOS 9.3 or later
Description and features
FIBARO CO Sensor is a HomeKit-enabled carbon monoxide detector using Bluetooth® low energy technology.
Its high sensitivity allows detecting the presence of carbon monoxide (CO) gas at the early stage in order to prevent carbon monoxide poisoning.Alarm is signaled with a built-in siren, blinking LED indicator, and by sending information to your iOS device.Additionally, the accessory is equipped with a temperature sensor.
Main features of FIBARO CO Sensor:
- compatible with Apple HomeKit technology
- Bluetooth® low energy technology for wireless communication
- detects tampering when the casing is opened
- wall-mounted
- battery-powered
- alarm signaled with a built-in siren and LED diode
- built-in temperature sensor measures ambient temperature
DESCRIPTION AND FEATURES
Powering the accessory
 |
1. Turn the cover counter-clockwise. |
 |
2. Take of the cover. |
 |
3. Remove the paper strip protecting the battery. |
 |
4. Proper powering up will be conirmed with a short beep. |
| 5. Pair the accessory if you want to use it with HomeKit. |
NOTEFIBARO CO Sensor may operate as a standalone carbon monoxide detector or may be used in cooperation with HomeKit technology as a part of mart home system.
POWERING THE ACCESSORY
Pairing the accessory
- Open the Settings app on your iOS device.
- Go to the Bluetooth® section, and turn the Bluetooth® on.
- Place the accessory next to your iOS device.
- Open a HomeKit compatible app of your choosing on your iOS device.
- Open the pairing window in your HomeKit app to detect available accessories.
- Choose CO Sensor you wish to pair.
- You can identify it – CO Sensor will blink green.
- Find HomeKit Setup Code on the last page of Quick Start Guide included in the box that looks like this:
- Start pairing with your HomeKit app.
- Point your iOS device’s camera at the Setup Code to scan it or enter the Setup Code manually.
- If entered Setup Code is valid, the device will complete the setup process.
- Follow the instructions displayed in the application.
NOTERemember to keep your HomeKit Setup Code in safe place. You may need it in case of re-pairing.
PAIRING THE ACCESSORY
Physical installation
READ BEFORE INSTALLATION AND HEED ALL THE WARNINGS!
- The accessory should be installed below the ceiling level.
- The accessory should be installed on the wall, at least 30 cm (1 ft) away from the corners.
- The accessory should not be installed: in a bathroom, next to heat sources, within range of kids, obstructed from possible carbon monoxide sources, in direct sunlight.
- The accessory should be installed by a qualified installation.
- Do not paint the accessory.
- The accessory should be cleaned with a slightly damp cloth or moistened tissue.
Place of installation:
NOTERecommended height of installation is dependant on the purpose of the room and the height at which the head typically is.
Installation on the wall:
- Mount the cover on a wall.
- Attach the accessory to its cover.
- Turn the accessory clockwise to close it.
PHYSICAL INSTALLATION
Operating the device
Menu allows performing diferent actions. In order to use the menu:
- Press and hold the button for 3 seconds.
- You should hear a short signal while the LED diode blinks white.
- Release the button.
- Wait for the device to indicate desired menu position with a color:• White – confirmed the start of the irmware update process• Green• Magenta – reset the CO peak value• Yellow – the device reset
- Press the button to confirm the selection.
NOTECO Sensor must be detached from the wall and battery level must be greater than 30% of its full capacity to perform the firmware update process.
Resetting the accessory to factory defaults:The reset procedure allows restoring the accessory back to its factory settings including HomeKit pairing. Stored carbon monoxide and temperature measurements are not deleted.
- Press and hold the button.
- Release the button when the LED indicator glows white and short beep sounds.
- Click the button when the LED indicator glows yellow.
- After few seconds the device will be reset (confirmed by red LED indicator and long beep).
Self-test allows checking the operation of the accessory.To start the self-test:
- Press and hold the button.
- The LED indicator will glow white and you will hear a short beep.
- Release the button when you hear the irst alarm sequence.
- Move away from the accessory to protect your hearing.
If the self-test procedure does not result in emitting sound and red light signal, replace the accessory.
CAUTIONThe alarm is very loud! Only the first alarm sequence is quieter.
OPERATING THE DEVICE
Functionality
Carbon monoxide alarm:The CO Sensor alarms about abnormal levels of carbon monoxide concentration with 4 red blinks and 4 loud beeps (every 5 seconds).Alarm is also reported to your iOS device.
Carbon monoxide measuring and storing:The CO Sensor measures carbon monoxide concentration and reports. If the measured value differs from previously reported by at least 1ppm, accessory reports it to your iOS device.Last2500 measurements are stored in the non-volatile memory of the accessory and can be accessed via FIBARO for the HomeKit app.
Temperature measuring:The CO Sensor measures ambient temperature every 30 seconds. If the measured temperature differs from previously reported by at least 1°C (1.8°F), the accessory reports it to your iOS device.Last 2500 measurements are stored in the non-volatile memory of the accessory and can be accessed via FIBAROfor HomeKitapp.
Tamper detection:The CO Sensor detects tampering when the accessory is removed from its base and reports it to your iOS device. Tampering is indicated with one white blink and beep.
Battery level measuring:The CO Sensor measures attery level every 6 hours and reports it to your iOS device. Additionally, if the battery level is below 15%, the accessory will report low-level battery status to your iOS device and indicate it with one yellow blink and beep.
NOTEThe accessory measures temperature in the place of installation. Remember that the temperature near the ceiling may differ from that on eye level or the floor.
FUNCTIONALITY
Visual indications & acoustic signals
Indications and signals:The CO Sensor is equipped with a LED diode and a buzzer, signalling menu position and status of the accessory.
Accessory status indications:
|
What you hea |
What you see | What it means |
What to do |
| 4 x BEEPevery 5s | 4 x RED BLINKevery Ss | Detected pres- ence of carbon monoxide which can kill you! | 1.Open the windows
2.Move to fresh air! 3.Contact emergency services |
| 1 x BEEP | 1 x YELLOW BLINKevery 30s | Low battery level | Replace the battery |
| 1 x BEEPevery 30s | – | Sensor error | Reset the accessory,replace if no effect |
| 2 x BEEP | 1 x CYAN BLINKevery 30s | End of lifespan | Reset the accessory,replace if no effect |
| 1 x BEEP | 1 x WHITE BLINK | Tamper alarm | Check the housing |
| _ | 1 x GREEN BLINKafter button press | Accessorypowered | _ |
| 1 x BEEP | 1 x GREEN BLINK after powering | Paired withHomeKit | – |
| 1 x BEEP | 1 x RED BLINK after powering | Not paired withHomeKit | – |
| – | CYAN BLINKING | Firmware update | Wait for completion |
NOTEReplace the accessory before date on the front or if sensor error is detected.
VISUAL INDICATIONS & ACOUSTIC SIGNALS
Battery
FIBARO CO Sensor can be powered with a CR123A (included) battery. The estimated battery life with accessory on default settings is 3 years (tested with Panasonic Industrial Lithium).
Checking battery level:The CO Sensor measures battery level every 6 hours and reports it to your iOS device. Additionally, if the battery level is below 15%, the accessory willreport low-level battery status to your ios device and indicate it with one yellow blink and a short beep.
Replacing the battery:
- Remove the accessory from the cover by turning it counter-clockwise.
- Pull the paper strip to take out the battery.
- Press and hold the button for at least one second.
- Insert a new CR123A battery observing the polarities shown inside.
- Attach the accessory to its cover by turning it clockwise and perform the test (as described in #5: Operating the device).
- Launch your HomeKit app and swipe down to refresh the device state.
CAUTIONUsing batteries other than specified may result in an explosion. Dispose of properly, observing environmental protection rules.
CAUTIONUse only the type of battery specified in this manual and keep proper polarity! i
NOTEIt is required to launch the HomeKitcompatible app, open the accessory view and swipe down the screen to refresh its state after each battery replacement.
Specifications
|
Power supply: |
CR123A 3.0V battery (included) |
| Battery life: | 3 years on default settings (tested with Panasonic Industrial Lithium) |
| Lifespan under typical conditions: | 8 years |
| CO concentration measurement range: | 0 – 450 ppm |
| Measuring accuracy: | ±10ppm / ±5% |
| Alarm response times: | 50ppm 60-90min100ppm 10-40min300ppm <1.5min |
| Alarm siren sound level: | 85 dBA at 3 meters (10 feet) |
| Operating temperature: | 0 – 50°C (32-122°F) |
| Operating humidity: | 10-95%RH without condensation |
| Conformity with EU requirement | RED 2014/53/EURoHS 2011/65/EUEN 50291-1:2010 |
| Radio protocol: | Bluetooth® low energy |
| Radiofrequency: | 2.4 GHz |
| Range: | up to 50m (free range) (164 feet) Dimensions (d x h): |
| Dimensions (d x h): | 65 x 28 mm (2.56 x 1.1 inches) |
CAUTIONUsing batteries other than specified may result in an explosion. Dispose of properly, observing environmental protection rules. NOTEReplace the accessory before date on the front or if sensor error is detected.
Regulations
Legal NoticesAll information, including, but not limited to, information regarding the features, functionality, and/or other product specification are subject to change without notice. Fibaro reserves all rights to revise or update its products, software, or documentation without any obligation to notify any individual or entity.FIBARO and Fibar Group logo are trademarks of Fibar Group S.A. Apple, iPhone, iPad, iPad Air, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. HomeKit is a trademark of Apple Inc.The Bluetooth word mark is a registered trademark of Bluetooth SIG, Inc. All other brands and product names referred to herein are trademarksof their respective holders.Use of the Works with Apple HomeKit logo means that an electronic accessory has been designed to connect specifically to iPod touch, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
WarningThis product is not a toy. Keep away from children and animals!Information according REACHThe included Panasonic CR123A battery contains 1,2-Dimethoxyethane substances. Normal use of the device does not expose the user to a given substance
Declaration of conformityHereby, Fibar Group S.A. declares that the device is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.manuals.ibaro.com
WEEE Directive Compliance
Devices labeled with this symbol should not be disposed of with other household wastes. It shall be handed over to the applicable collection point for the recycling of waste electrical and electronic equipment.
REGULATIONS
References
[xyz-ips snippet=”download-snippet”]