ROCKVILLE UT525B Marine UTV/ATV ROll Bar/ Wakeboard Tower Speakers Owner’s Manual

Table of Contents

UT525B5.26^–MARINE UrTV/ATV ROLL BAR/ WAKEBOARD TOWER SPEAKERSOWNER’S MANUAL

WHO READS MANUALS?Instead, go to vimeo.com/536315183 or scan the QR code and watch a short video that shows you how to set this item up and how to use it.

If you prefer written instructions, please read ahead!With Rockville, you get many options.

https://vimeo.com/536315183

Missing items? If you ordered a bundle That includes more than one product and you are missing part of your bundle then it just means your order shipped from two different warehouses. You will receive the remaining items very soon. If you have any concerns or inquiries, feel free to call our customer support center at 1-646-758-0144, Monday through Thursday, 9 am to 10 pm EST, and Fridays, 9 am to 3 pm EST

Thank you for purchasing these Rockville UT525B roll bar/wakeboard tower speakers. Please read this owner’s manual carefully for proper use of your UT525B. Should you need assistance, please call our technical helpline at 1-646-758-0144, Monday through Thursday, 9 am to 10 pm EST, or Fridays, 9 am to 3 pm EST.

Includes

Two tower speakers
Mounting brackets and mounting hardware to fit 1.5″, 1.75″, 1.875″, or 2″
Installation hardware
Owner’s manual
Warranty card

Parts list

1	Non slip rubber pad (48 x 30mm)	2 PCS
2	Non slip rubber strip (120 x 14 x 1mm)	4 PCS
Non slip rubber strip (130 x 14 x 2mm)	4 PCS
3	Aluminum ring 1.75	4 PCS
4	Aluminum ring 7	4 PCS
5	Non-slip flat washer for M6 screw	4 PCS
6	Non-slip nut for M6 screw	4 PCS
7	M6 x 60mm screw	4 PCS

Installation safety considerations

Please remember that these are heavy products that will be installed in a boat or off-road vehicle. These vehicles can travel at high speeds and be unstable, so please keep this in mind and use extreme caution.

Do not mount the speaker in a location where someone could either walk into it or strike their head. During a turbulent ride, please make sure that you do not lose footing and fall or hit the unit as it may cause injury.
Secure the wires to the speaker in multiple locations along the route to the audio source so there are no hanging wires. Having nonsecure wires, especially in low light conditions, can cause entanglement and injury.
Make sure to use the included rubber inserts when securing the speaker to the wake tower. Do not overtighten the clamp. After installation is complete, and before operating your vehicle or vessel please check all bolts to ensure they are completely tightened
Do not install these speakers where they may block the view of the operator or prevent the safe operation of the vehicle or vessel.

Installation

The two screws can be unbolted to loosen the metal base of the mounting ring to adjust the marling angle. Make sure to put all components of the mounting hardware in a safe.

Place the front Ober pad on the metal base of the mounting ring.

Determine the mounting cage bar size and place the appropriate rubber strip around it This will ensure a proper fit and prevent scratching. Push the aluminum ring over the bar. Align the aluminum rings with the metal base of the mounting rings on the wake tower speaker.

Secure the aluminum rings to the metal base using a pair of M6 x 60mm screws, M6 It washers, and M6 locknuts as illustrated. The locknut should be installed into the hex-shaped recess on one end of each ring. Do not overtIghten. To change the position of the weaker loosen the screws, adjust the speaker, then retighten the screws.

UT525B wake tower speaker installation completed.

After loosening the two screws and determining the optimal age for your speakers co the mowing bar, tighten the two screws in place to secure the metal base of the mounting ring tightly.