SHURE MX415DUAL Dual-Capsule Gooseneck Microphone User Guide

SHURE MX415DUAL Dual-Capsule Gooseneck Microphone

General DescriptionThe Shure Microflex MX415DUAL dual-capsule gooseneck microphone features two electret condenser cartridges mounted in a single low-profile housing and two preamp-equipped outputs providing redundant audio for critical, multi-feed live sound and professional broadcast applications. With a 15” overall length, the MX415DUAL includes a flexible top gooseneck section for optimal placement, and includes all the mounting accessories required for installation into a lectern or tabletop configuration.

Features

• Wide dynamic range and frequency response for accurate sound reproduction
• Dual 1 cm cardioid Microflex interchangeable cartridges
• Dual 5-foot cables exiting out bottom of mic, terminating in two TQG Connectors
• Two external in-line preamps
• Shock mount provides over 20 dB of isolation from surface vibration noise
• RF filtering with CommShield technology

Interchangeable Cartridges

Microflex microphones use interchangeable cartridges that allow you to choose the polar pattern for different installations.

Windscreen

• Snap into place when fully seated.
• To remove, grip under the wider sides of the foam and gently pull.
• Provides “pop” protection of 30 dB for mesh and 40 dB for foam windscreens.

Installation

Mount the microphone using a flange or shock mount.Important: The dot on the microphone and TQG connector indicates which cartridge is connected to which connector. The included RK100PK phantom-powered preamps converts the TQG connector to an XLR output.

A13HDB Flange:

1. Mark and drill 3 starter holes for the screws using the flange as a template.
2. Secure the flange to the mounting surface with screws.
3. Thread the microphone clip to the flange, then mount the microphone to the clip.Note: Use the extension tube with the microphone clip and flange if desired.

RPM640 Flange:

1. Drill a 22 mm (7/8 in.) diameter hole in the mounting surface.
2. Mark and drill 3 starter holes for the screws using the flange as a template.
3. Insert the TQG connectors through the mounting flange.
4. Slide the retaining ring over the bottom of the gooseneck base until is flush to the bottom of the flange, then press the ring firmly into place.
5. Secure the flange to the mounting surface with screws.

A400SM Shock Mount:

1. Drill a 44 mm (1-3/4 in.) diameter hole in the mounting surface.
2. Mark and drill 3 starter holes for the screws using the shock mount as a template.
3. Secure the shock mount to the mounting surface with screws.
4. Insert the TQG connectors through the hole, then insert the microphone base.

Dimensions

Accessories

Specifications

Cartridge TypeElectret CondenserFrequency Response50–17000 HzPolar PatternCardioidOutput Impedance180 ΩOutput ConfigurationActive BalancedSensitivity@ 1 kHz, open circuit voltage –35 dBV/Pa (18 mV)Maximum SPL1 kHz at 1% THD, 1 kΩ load 124 dBSelf NoiseA-weighted 28 dB SPLSignal-to-Noise RatioRef. 94 dB SPL at 1 kHz 66 dBDynamic Range1 kΩ load, @ 1 kHz 96 dBCommon Mode Rejection10 Hz to 100 kHz 45 dB, minimumClipping Levelat 1% THD -6 dBVPolarityPositive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR connector.Weight205 g (7.23 oz)

Environmental Conditions

Power Requirements11–52 V DC, 2.0 mA

Certifications

Meets essential requirements of all applicable European Directives.Eligible for CE marking.The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact information please visit www.shure.com The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance

Authorized European representative:Shure Europe GmbHGlobal ComplianceJakob-Dieffenbacher-Str. 1275031 Eppingen, GermanyPhone: +49-7262-92 49 0Email: [email protected]www.shure.com

References

• 
  Shure: Microphones, Wireless microphones, in-ear monitoring, earphones, headphones
• 
  Documentation Finder – Shure Europe