DOGCARE UT02 EDGE Ultrasonic Dog Trainer and Anti Barking Device User Guide
Important Safety Instructions
READ ALL INSTRUCTIONS BEFORE USING THE ULTRASONIC DOG TRAINER.
Do not point at humans or hold close to a human ear. Permanent hearing damage may result.
Do not use for purposes other than training dogs.
Keep out of the reach of children.
Do not use this device on dogs under 6 months old. Or on sick, old, pregnant, or aggressive dogs.
This device is not waterproof.
Do not disassemble. Contact customer service when a repair is required.
Quick Start
- Turning on: push the ON/OFF SWITCH up to turn on.
- Deterrent mode: press the DETER BUTTON, the ultrasonic dog trainer will emit ultrasonic sound as a warning.
- Note: the ultrasonic sound travels directionally. Make sure to point the ultrasonic trainer towards the front of the dog while using.
- Charging: charge the ultrasonic dog trainer with the attached USB cable.
- Attaching the lanyard: use the lanyard to help keep yourultrasonic dog trainer securely on your wrist.
Uses
Stop excessive barking
Correct Unwanted Behavior
For Indoor and outdoor use
Key Benefits
Original UltraBooster Technology
Long-Lasting Rechargeable Battery
Vibration Feedback Clear Perception
Up to 30 ft Range of Coverage
Up to 6 Months Standby Time
Ergonomic Shape More User-Friendly
In the Box
Get to Know Your Ultrasonic Dog Trainer
ULTRASONIC BOOSTER: DogCare’s original ultrabooster technology. Ultrasound is more directional, and travels farther away when it enters the ultrasonic speaker booster.
How Your Ultrasonic Dog Trainer Works
Turning On
Push the On/OFF SWITCH up to the ON position to turn on the ultrasonic trainer. When the dog trainer is turned on, it will vibrate slightly twice and the STATUS LED will flash twice.
Standby
After the dog trainer is turned on and isn’t operated , it will enter standby status. When the dog trainer is in standby mode the status LED will flash every 5 seconds. (When the power is sufficient , the green light flashes once every 5 seconds. When the power is low, the red light flashes once every 5 seconds. When the power is too low, the STATUS LED does not light up.)
Turning offPush the ON/OFF SWITCH down to the OFF position to turn off the ultrasonic trainer. When the ultrasonic trainer is off, all buttons will be inactive.
ChargingUse the attached USB cable to charge the ultrasonic trainer. It usually takes 4-5 hours to fully charge. When the charging cable is correctly connected, the ultrasonic trainer will vibrate slightly, and the STATUS LED will turn red.When the STATUS LED is red, it indicates that the ultrasonic trainer is charging. When the STATUS LED turns from red to green, it indicates that the ultrasonic trainer is fully charged. If powered on while charging, the ultrasonic trainer can worknormally.
Deterrent ModeTo stop inappropriate dog behavior, make sure the ultrasonic trainer is on, then press the DETER BUTTON, The ultrasonic trainer will emit ultrasonic sound, it will vibrate, and the STATUS LED will flash green quickly, indicating that the mode is functioning.
When your dog barks excessively or attempts to destroy something, press this button and the dog trainer will emit an ultrasonic sound to stop your dog at that exact moment.
When your dog stops, quickly pet it, or give it a treat or a toy to confirm that it was correct to stop, and that it can be rewarded for good behavior. In this way, you can effectively train your dog.Repeated use of this method can reinforce the training effect.
Note: This feature may not be suitable for all dogs. It is not recommended to use this function with sick or elderly dogs, puppies, pregnant or very aggressive dogs. You can use this function under the guidance of a professional dog trainer.
Low Battery Alert
When the dog trainer’s battery is low, the dog trainer will work normally and perform the following actions. In this case, the device should be charged soon:
- The STATUS LED flashes red twice when you turn on the device.
- When the device is on standby, the STATUS LED will flash red once every 5 seconds.
Empty Battery Alert
When the battery is empty and needs to be charged immediately, the STATUS LED will no longer light up. Pressing any button on the ultrasonic trainer will result in the STATUS LED flashing red 4 times quickly. At this time, the ultrasonic trainer cannot work normally and can only be used after charging.
Battery Maintenance
The ultrasonic trainer uses a lithium battery which requires routine recharging to achieve the maximum battery life span. If the ultrasonic trainer is unused for an extended period of time, fully charge the battery every 3 months to maintain battery life.
Warning
- Do not point at humans or hold close to a human ear. Permanent hearing damage may result.
- This device is only to be used for deterring or training dogs. It cannot be used for other purposes.
- This device should be placed out of the reach of children. Close attention is necessary when being used near children. Children should be supervised to ensure that they do not play with this product.
- It is not recommended for people with weak physical, sensory or mental capabilities, or lack of experience and knowledge to use this product.
- Do not use this device on dogs under 6 months old. Or on sick, old, pregnant dogs. For aggressive dogs, please use this device with caution.
- Do not disassemble, bump, squeeze, or put into fire.
- This device is not waterproof. Do not handle the device with wet hands. Do not use if immersed in water.
- Keep away from heat sources when using the device. Do not use if there is thermal expansion.
- When not in use, the device should be stored in a cool and dry place away from fire and water.
- Use the device within the range of coverage of 30 ft. When the operating distance exceeds 30 ft, the ultrasonic sound is less effective.
- Ultrasonic sound will be deflected when they meet obstructions. Ensure that the front of the device is unobstructed during use.
- The speaker booster is in the shape of a horn, and there is a risk of breaking it when it’s dropped.
- Contact the DogCare customer service when a service or repair is required. Do not disassemble the device as incorrect reassembly may result in an electric shock or fire.
Troubleshooting
- No response after pressing a button.
- Check whether the ON/OFF SWITCH is in the ON position.
- It is likely that the battery was running low causing the device not to respond. Charge the ultrasonic trainer, then turn on the trainer and press any button to test the response. The device should function normally after the battery has been charged.
- When pressing the button, the STATUS LIGHT flashes red, but the ultrasonic trainer does not respondThe battery is empty and needs to be charged.
- The ultrasonic trainer has no effect on dogs
- The ultrasonic sound travels directionally. Make sure to point the ultrasonic trainer towards the front of the dog while using.
- Check whether the ultrasonic speakers are blocked by other objects.
- When using the device, check if the distance is too far. The effective distance of this dog trainer is 30 ft. Beyond this effective distance, the ultrasonic sound pressure will be attenuated and thus ineffective.
- If the dog’s earholes are blocked by its ears, the ultrasonic sound may be blocked, and the result will not be as effective.
Feel free to contact our support team via+1-833-220-1900 or [email protected]
Terms of use and limitation of liability
Using this product means that you accept all terms and conditions.Please familiarize yourself with local laws before using this product, and do not use this product in violation of local laws.We are not responsible for any direct or indirect losses caused by incorrect use of this product. All risks of using this product are borne by the user.We reserve the right to change the terms, conditions, and notices of this product.
Product Specifications
|
Model |
UT02 |
| Dimensions |
5.7”* 1.6“ • 1.4″ |
|
Weight |
4.1 oz |
| Water rating |
Non-waterproof, keep away from water |
|
Battery |
2000mAh lithium battery |
| Charging time |
4 to 5 hours to fully charge |
|
Charging interface |
Micro USB |
| Operating environment |
14°F-104°F, «95%Rh |
|
Standby time |
6 months |
| Range of coverage |
30 ft |
Model: UT02Contact DogCare for support and service
[xyz-ips snippet=”download-snippet”]