allen roth 1227VA-48-201-903 48-in Vanity with Top User Manual

allen roth 1227VA-48-201-903 48-in Vanity with Top

PACKAGE CONTENTS

HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)

SAFETY INSTRUCTIONSPlease read and understand this entire manual before attempting to assemble, operate or install the product.

WARNINGThere are several assembly steps, including unpacking, that require two adults.

CAUTION

• DO NOT try to pry off top from vanity, as damage to top or vanity may occur.
• Follow these instructions closely, take your time, and use care while assembling this vanity.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.Estimated Installation Time: 20-30 minutes (24 hours for silicone caulk to dry).Tools Required for Installation (not included): Phillips screwdriver, utility knife or scissors, silicone caulk, power drill with drill bit.Helpful Tools (not included): Measuring tape, level.

INSTALLATION INSTRUCTIONS

1. Please remove the top (D) from the vanity (A). Place the top (D) and backsplash (E) face down onto a scratch-free surface such as a foam sheet that came in the packaging.
2. To remove drawers preassembled in vanity (A), fully extend drawers. Locate plastic levers on metal glide tracks at left and right sides of drawer box.To disengage drawer box from glides, push on plastic levers. Then, gently lift drawer up to remove it from vanity (A).
3. With the help of another person, place vanity (A) upside down on a scratch free surface. Place leg (B) into correct position on vanity (A). Insert bolts (AA), spring washers (EE) and washers (BB) into the predrilled holes on the inside of the vanity (A). Tighten bolts (AA) with allen wrench (DD). Repeat for additional one leg (B); DO NOT install the final two legs (B).Hardware Used
4. Place shelf (C) into notches of the two installed legs (B). Push final two legs (B) snug to the shelf (C). Insert bolts (AA), spring washers (EE) and washers (BB) into the predrilled holes on the inside of the vanity (A), tighten with allen wrench (DD).Hardware Used
5. Insert bolts (AA), spring washers (EE) and washers (BB) into the predrilled holes on the inside of the legs (B), tighten with allen wrench (DD).Hardware UsedNote: Clean area where the vanity (A) will be permanently located prior to beginning installation, ensuring the vanity (A) will not interfere with any water supply and drain lines once mounted.Note: Use preassembled levelers on legs of vanity (A) to level the item. Twisting the levelers counterclockwise will increase the height of vanity (A), twisting them clockwise will decrease it.
6. With two people, carefully place vanity (A) against the wall in its final location.From inside vanity (A), drill hole through vanity mounting area and into wall studs. Using mounting hardware (not included) appropriate for your installation site, secure vanity (A) to wall stud. If possible, secure vanity (A) totwo wall studs for increased stability.WARNINGVanity (A) MUST be secured to wall.Note: At this stage it may be easier to install the faucet and drain kit (not included) to top (D) per the manufacturer’s instructions, before moving on to Step 7.
7. Apply stain free silicone caulk (not included) to the top edge of vanity (A). With the help of another adult, gently lower top (D) onto the vanity (A). Wipe away any excess caulk with a soft cloth, and wait approximately 24 hours for it to dry.
8. To reinstall drawers into vanity (A), fully extendmetal glide tracks. Gently lower and slide drawer box into rear glide catch. Next lower drawer box down to completely rest on extended glides. Then, push plastic levers to lock the drawer box in place. Repeat for remaining drawers.Note: To adjust the drawer box height, spin the adjustment wheel to the left to raise the drawer box or spin the adjustment wheel tothe right to lower the drawer box. You can adjust the left and right side glide heights independently in order to find the drawers best alignment position.CAUTIONDO NOT force drawer or damage to glide(s) may occur. If drawer does not slide in with ease, remove and try again from the start.
9. Apply silicone caulk (not included) to unpolished side and bottom of backsplash (E). Position backsplash (E) on top (D) and against wall. Clean any excess caulk before allowingto dry.Assembly is now complete. Install desired faucet and drain assemblies (neither included) per the manufacturers’ instructions to complete the installation.

CARE AND MAINTENANCE

• Dust the vanity regularly with a soft, non-lint producing cloth or household dusting product.
• You can clean the vanity with a gentle, non-abrasive household cleaner.
• Make sure to dry the wood immediately with a soft cloth or towel.
• The stone top can be cleaned using standard marble cleaning agents available at your local supplier.
• Tips for using touch-up pen (CC): For scratches, stroke in direction of scratch. Rub off excess colorant promptly with a soft cloth.

IMPORTANT

• Shade variations and patterns are an inherent characteristic of stone (e.g. granite, marble, engineered stone). Stone tops will vary from product to product. Use caution placing items such as soap or any fragranced material on the stone surface. Use a soap dish, coaster or similar item to protect the surface if placing any soap or fragranced products on the stone.
• If soap or fragranced products come in contact with the stone top, rinse the surface with water and dry using a soft non-abrasive cloth.WARNING: Must use cleaning agents safe for stone. Check your cleaning agents use restrictions before using on any stone. Damage to the stone may result. Vanity manufacturer not responsible for damage caused by improper cleaning agents or soaps used. Warranty will not cover damage caused by the use of improper soaps or cleaning agents.
• DO NOT use products to clean the stone top that contain acetone, lemon, vinegar or other acids as these may cause damage to the stone surface.
• Periodically reseal the stone top using an appropriate stone sealer available from your local home store. Follow the manufacturer’s directions on how to apply.

WARRANTY

The manufacturer warrants this item against defects in materials and workmanship for a period of one (1) year from the date of original retail purchase. This warranty applies only to the original purchaser. This warranty does not apply to any damage on the product by accident, misuse, or modified, improper installation or by affixing accessories not produced by the manufacturer. The manufacturer is not accountable whatsoever for product installation during the warranty period. There is no further expressed warranty. The manufacturer shall not be legally responsible for incidental, consequential or special damages arising at or in connection with product use or performance except as may otherwise be accorded by law. The manufacturer disclaims any and all implied warranties.

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 1-866-439-9800, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at [email protected] or visit www.lowespartsplus.com.

References

• 
  Lowe\’s Parts Plus