allen roth 48-in Vanity with Top 1605VA-48-279-926 Installation Guide

welcoming · sophisticated · inspiringITEM #269449948-IN VANITYWITH TOPMODEL #1605VA-48-279-926SM20494

ALLEN + ROTH and logo designs are trademarks or registered trademarks of LF, LLC. All rights reserved.

ATTACH YOUR RECEIPT HERESerial Number__________________ Purchase Date__________________Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-439-9800, 8 a.m. – 8 p.m., EST, Monday – Sunday.You could also contact us at [email protected] or visit www.lowespartsplus.com.

PACKAGE CONTENTS

HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)

SAFETY INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, operate or install the product. WARNING

• There are several assembly steps, including unpacking, that require two adults.

CAUTION

• DO NOT try to pry off the top from vanity, as damage to top or vanity may occur.
• Follow these instructions closely, take your time, and use care while assembling this vanity.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

PREPARATION

Before beginning the assembly of the product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.Estimated Installation Time: 35 minutes (24 hours for silicone caulk to dry).Tools Required for Installation (not included): Phillips screwdriver, utility knife or scissors, silicone caulk, power drill with a drill bitHelpful Tools (not included): Measuring tape, level

INSTALLATION INSTRUCTIONS

1. Please remove the top (B) from the vanity (A). Place the top (B) and backsplash (C) face down onto a scratch-free surface such as a foam sheet that came in the packaging.
2. To remove drawers preassembled in vanity (A), fully extend drawers. Locate plastic levers on metal glide tracks at left and right sides of the drawer box.To disengage drawer box from glides, push on plastic levers. Then, gently lift the drawer up to remove it from the vanity (A).Note: Clean area where the vanity (A) will be permanently located prior to beginning installation, ensuring the vanity (A) will not interfere with any water supply and drain lines once mounted.
3. With two people, carefully place vanity (A) against the wall in its final location.While holding the vanity base firmly against the wall, use the pre-assembled levelers on the bottom of each leg of the vanity (A) to level the item. Twisting the levelers counterclockwise will raise the height of the vanity (A), and twisting them clockwise will lower the vanity.Once the vanity is in place, against the wall, and level from front to back and side to side, drill a hole through the vanity mounting areaand into the wall studs (as illustrated in diagram 3). Using appropriate mounting hardware (not included), secure the vanity (A)to a wall stud. If possible, secure the vanity (A) to two wall studs for increased stability. WARNINGVanity (A) MUST be secured to wall.Note: At this stage, it may be easier to install the faucet and drain kit (not included) to top (B) per the manufacturer’s instructions, before moving on to Step 4.
4. Apply stain-free silicone caulk (not included) to the top edge of vanity (A). With the help of another adult, gently lower top (B) onto the vanity (A). Wipe away any excess caulk with a soft cloth, and wait approximately 24 hours for it to dry.
5. Apply silicone caulk (not included) to unpolished side and bottom of backsplash (C). Position backsplash (C) on top (B) and against the wall. Clean any excess caulk before allowing it to dry.
6. To reinstall drawers into a vanity (A), fully extend metal glide tracks. Gently lower and slide drawer box into rear glide catch. Next lower drawer box down to completely rest on extended glides. Then, push plastic levers to lock the drawer box in place.Repeat for remaining drawers.Note: To adjust the drawer box height, spin the adjustment wheel to the left to raise the drawer box or spin the adjustment wheel to the right to lower the drawer box. You can adjust the left and right-side glide heights independently in order to find the drawer’s best alignment position.CAUTIONDO NOT force drawer or damage to glide may occur. If the drawer does not slide in with ease, remove it and try again from the start.
7. From the front of the assembly, insert shelf pins at the desired height, ensuring they are level. Place shelf (I) on top of shelf pins.Repeat for the remaining shelf (I).
8. If you need to adjust the doors, do so in the following manner.To adjust the door up or down, loosen screws (a) on both hinges, adjust the door, and retighten the screws.To adjust the door left or right, turn screws (b) on both hinges, in and out.To adjust the door in or out, loosen screws (c) on both hinges, adjust the door, and retighten screws.Assembly is now complete. Install desired faucet and drain assemblies (neither included) per the manufacturers’ instructions to complete the installation.

CARE AND MAINTENANCE

• Dust the vanity regularly with a soft, non-lint-producing cloth or household dusting product.
•  You can clean the vanity with a gentle, non-abrasive household cleaner.
• Make sure to dry the wood immediately with a soft cloth or towel.
• The stone top can be cleaned using standard marble cleaning agents available at your local supplier.
•  Tips for using a touch-up pen (AA): For scratches, stroke in direction of the scratch. Rub off excess colorant promptly with a soft cloth.

IMPORTANT

• Shade variations and patterns are an inherent characteristic of stone (e.g. granite, marble, engineered stone). Stone tops will vary from product to product. Use caution placing items such as soap or any fragranced material on the stone surface. Use a soap dish, coaster or similar item to protect the surface if placing any soap or fragranced products on the stone.
• If soap or fragranced products come in contact with the stone top, rinse the surface with water and dry using a soft non-abrasive cloth.
• WARNING: Must use cleaning agents safe for stone. Check your cleaning agents’ use restrictions before using on any stone. Damage to the stone may result. Vanity manufacturers are not responsible for damage caused by improper cleaning agents or soaps used. Warranty will not cover damage caused by the use of improper soaps or cleaning agents.
• DO NOT use products to clean the stone top that contains acetone, lemon, vinegar or other acids as these may cause damage to the stone surface.
•  Periodically reseal the stone top using an appropriate stone sealer available from your local home store. Follow the manufacturer’s directions on how to apply.

WARRANTY

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 1-866-439-9800, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at [email protected] or visitwww.lowespartsplus.com.

Printed in VietnamALLEN + ROTH and logo designs are trademarks or registered trademarks of LF, LLC. All rights reserved.

References

• 
  Lowe\’s Parts Plus