ULINE H-2606 Fellowes PS-79Ci Paper Shredder Instruction Manual

H-2606 FELLOWES® PS-79Ci PAPER SHREDDER1-800-295-5510uline.com

NOTE: Read these instructions before use. Do not discard. Keep for future reference.

PARTS

REF. DESCRIPTION
1 SafeSense’ Technology
2 Paper entry
3 See safety instructions
4 CD/Card safety flap
5 Pullout bin
6 Casters
7 Disconnect power switch
8 Control Panel and LEDs

CAPABILITIES

Will shred paper, plastic credit cards, CD/DVDs, staples and small paper clips.Will not shred adhesive labels, continuous form paper, transparencies, newspaper, cardboard, large paper clips, laminates, file folders, X-rays or plastic other than noted above.Paper Shred SizeCross-Cut ­ 5/32 x 1/”Maximum

  • Sheets per pass ­ 16*
  •  CDs/Cards per pass ­ 1*
  • Paper entry width ­ 9″

*8/ x 11″, 20 lb. paper at 120V, 60 Hz, 4 amps; heavier paper, humidity or other than rated voltage may reduce capacity.Maximum recommended daily usage rates: 500 sheets, 25 credit cards, 10 CDs, 16 sheets per pass.

Fellowes SafeSense® shredders are designed to operate in home and office environments ranging between 50-80º F and at 40-80% relative humidity.

SAFETY

  •  The operation, maintenance, and service requirements are covered in these instructions. Read completely before operating shredder.
  •  Keep away from children and pets. Keep hands away from the paper entry. Always set to OFF (O) or unplug when not in use.
  •  Keep foreign objects ­ gloves, jewelry, clothing, hair, etc. ­ away from shredder openings. If an object enters the top opening, switch to Reverse ( ) to back out the object.
  • Do not use aerosol products, petroleum-based or aerosol lubricants on or near shredder. Do not use canned air or air dusters on the shredder. Vapors from propellants and petroleum-based lubricants may combust, causing serious injury.
  •  Do not use if damaged or defective. Do not disassemble the shredder. Do not place near or overheat source or water.
  • This shredder has a disconnect power switch that must be in the ON (I) position to operate the shredder. In case of emergency, move the switch to the OFF (O) position. This action will stop the shredder immediately.
  • Avoid touching exposed cutting blades under the shredder head.
  •  Shredder must be plugged into a properly grounded wall outlet of the voltage and amperage designated on the label. The grounded outlet or socket must be installed near the equipment and easily accessible. Energy converters, transformers, or extension cords should not be used with this product.
  •  Fire hazard ­ do not shred greeting cards with sound chips or batteries.
  •  For indoor use only.
  •  Unplug shredder before cleaning or servicing.

CASTER INSTALLATION

OPERATING INSTRUCTIONS

Continuous operation up to 20-minute maximum.NOTE: Shredder runs briefly after each pass to clear entry. Continuous operation beyond 20 minutes will trigger a 30-minute cool-down period.

  1.  Plugin and put disconnect power switch in ON (I) position.
  2.  Press ON ( ) to activate (blue).
  3.  Feed paper straight into paper entry and release.
  4. To shred CDs or credit cards, rotate safetyflap into place.
  5.  Hold card/CD at the edge. Feed into the center of entry and release.
  6.  When finished shredding, set to OFF ( )position.

PRODUCT FEATURES

JAM-PROOF SYSTEMA jam-proof system eliminates paper jams and powers through tough jobs.

SAFESENSE® TECHNOLOGY

Stops shredding immediately when hands touch the paper opening.

  1. Turn the shredder ON () to activate SafeSense®.
  2.  Touch the test area and look for the SafeSense® indicator to illuminate.
  3. SafeSense® is active and working properly.
  4. If the hand is held on the SafeSense® area for more than 3 seconds, the shredder will shut off.

ENERGY-SAVING SYSTEM

An energy-saving system creates optimal energy efficiency.NOTE: Sleep mode shuts down after 2 minutes of inactivity.

  1. To get out of sleep mode, touch the control panel.
  2.  Insert paper.

MAINTENANCE

OILING SHREDDERAll cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding and could ultimately stop running. To avoid these problems, we recommend oiling shredder each time user empties the waste bin.CAUTION! Use only non-aerosol vegetable oil in a long nozzle container, such as S-16094.

Follow the oiling procedures below and repeat twice.

CLEANING AUTO-START INFRARED SENSORSPaper detection sensors are for maintenance-free operation. However, on rare occasions the sensors may become blocked by paper dust, causing the motor to run even when there is no paper present.

NOTE: Two paper detection sensors are located in the center of the paper entry.

TROUBLESHOOTING

OPERATING ISSUE RECOMMENDATIONS
Overheat Indicator When the Overheat Indicator is illuminated:1. Allow the shredder to cool down.2. Resume shredding once the Overheat Indicator is no longer illuminated.
Bin Open When Bin Open is illuminated:1. Close the bin.2. Resume shredding.
Bin Full When Bin Full is illuminated:1. Empty the bin.2. Resume shredding.

TROUBLESHOOTING CONTINUED

OPERATING ISSUE RECOMMENDATIONS
Remove Paper When Remove Paper is illuminated:

  1.  Press the ‘reverse’ button () and remove the paper.
  2.  Reduce paper quantity to an acceptable amount and refeed into the paper entry.
SafeSensex Indicator When SafeSense’ Indicator is illuminated:

  1.  Remove hands from the proximity of the paper entry.

NOTE: If illuminated for more than three more seconds, the shredder will automatically turn off. In this case, press the power button on the control panel to resume shredding.

1-800-295-5510uline.com

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,