alpina YL-A07S-7 Oil Heater Radiator Instruction Manual
INSTRUCTION MANUAL
INDOOR HOUSEHOLD USE ONLY
WARNING: PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USING THE RADIATOR
When using an electrical appliance, basic safety precautions should always be observed, including the following:
- This appliance may be used by children 8 years of age or older and persons with reduced physical, sensory or mental capabilities orpersons with a lack of experience and knowledge when supervised or instructions concerning use of appliance in a safe way and understand hazards involved.
- Children under the age of 8 must be kept away from the device and connection line.
- Cleaning and user maintenance must not be carried out by children without supervision.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack ofexperience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Connect the appliance to single phase AC supply of the voltage specified on the rating plate.
- In order to avoid overheating, do not cover the heater.
- Never leave the heater unattended while it is in use. Always turn the product to the OFF position and unplug it from the electrical outlet when not in use.
- Extreme caution is necessary when any heater is used by or near children, invalids or elderly person and whenever the heater is leftoperating and unattended.
- The heater must not be located immediately below an electrical socket-outlet.
- Do not run cord under carpeting and do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic area andwhere it will not be tripped over.
- Do not operate the heater with a damaged cord or plug, or after the heater malfunctions, has been dropped, or damaged in any manner.
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person to avoid a hazard.
- Avoid the use of an extension cord as this may overheat and cause a risk of fire.
- Use the heater in a well-ventilated area. Do not insert or allow objects to enter any ventilation or exhaust opening. To prevent a possible fire, do not block air intakes or exhaust openings in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. Use the heater on flat, dry surfaces only.
- Do not place this heater near flammable materials, surfaces or substances, as there may be a risk of fire. Keep the above flammable materials, surfaces or substances at least 1m from the front of the product and keep them away from the sides and rear.
- Do not use the heater in any areas where petrol, paint or other flammable liquids are stored e.g. Garages or workshops as a hot, arcing or sparking parts inside the heater.
- Don’t use this heater in the immediate surroundings of a bath, a shower or a swimming pool. Never locate the heater where it may fall into bathtub or other water container.
- This heater is hot when in use. To avoid burns and personal injury, do not let bare skin touch hot surfaces. If provided, use handles when moving the product.
- Be sure that no other appliances are in use on the same electrical circuit as your product as an overload can occur.
- This heater is filled with a precise quantity of special oil.
- Repair requiring opening of the oil container are only to be made by the manufacturer or his service agent who should be contacted if there is an oil leakage.
- Regulations concerning the disposal of oil when scrapping the appliance have to be followed.
- The heater should not be used in a room, of which the floor area is less than 5 M2.
- The cord shouldn’t be placed nearby the hot surface of the appliance.
- NOTE: It is normal when the heaters are turned on for the first time or when they are turned on after having not been used for a long period of time the heaters may have noise inside, This will disappear when the heater has been on a short while.
OIL-FILLED RADIATOR YL-A07S-7
ASSEMBLY INSTRUCTIONS
The radiator is packaged with the feet unattached. You must attach them before operating the radiator.WARNING: Do not operate the radiator without its feet attached. Operate the radiator only while it is in the upright position (feet at the bottom, controls at the top); any other position could create a hazardous situation.
- Place the radiator body upside down in a scratch-resistant location; make sure it is stable and will not fall over.
- Unscrew the wing nuts from the U-shaped bolt provided, attach the Ushaped bolt to the U-profile flange between the first and second fins (near the front cover).
- To attach the castor-mounting plate to the radiator body, you should insert the threaded ends of the U-shaped bolt into the holes on the castor-mounting plate.
- Screw the wing nuts back onto the U-shaped bolt, fastening the wing nuts properly.
Note: Do not over tighten as this may cause damage to the radiator flange.
- Unscrew the spherical nut from the castor, align the shaft with the hole on the castor-mounting plate and insert, then screw on the spherical nut.
- Repeat 2, 3, 4 and 5 at the rear of the radiator to mount the rear castors.Note: The rear castors must be mounted between the end two fins.
INSTRUCTIONS FOR USE
- Before using the radiator, make sure that it is on a flat and stable surface. Damage may occur if it is placed on an incline.
- Set all the controls to the OFF position and insert the plug into a power outlet socket that is properly earthed (grounded). Make sure that plug fits firmly.
- Rotate the thermostat knob clockwise to MAX position and switch the radiator on as follows: just switch I on for low heat, just switch II on for medium heat, both switches on for high heat.
- When your room reaches the desired temperature, slowly rotate the thermostat knob anticlockwise (counterclockwise) until the indicator light goes out. The thermostat can now be left at this setting. As soon as the room temperature drops below the set temperature, the radiator will switch itself on automatically and remain on until the set temperature has been reached again. In this way, the temperature of the room is maintained while using electricity in the most economical way.
- If you want to change the temperature setting for the room, rotate the thermostat knob clockwise to raise the temperature or anticlockwise (counterclockwise) to lower it.
- This radiator includes an overheat protection system that shuts off the radiator when parts of it are getting excessively hot.
- To completely shut the radiator off, turn all the controls to OFF and remove the plug from the power outlet socket.
MAINTENANCE
- Always remove the plug from the power outlet socket and allow the radiator to cool down before cleaning the radiator.
- Wipe the radiator with a soft, damp (not wet) cloth.WARNING:Do not immerse the radiator in water.Do not use any cleaning chemicals such as detergents or anything abrasive on the radiator.Do not allow the interior of the radiator to get wet, as this could create a hazard.
- To store the radiator, wind its cable up, then put the radiator in a clean, dry place.
- If a malfunction occurs or if you are in any doubt, do not try to repair the radiator yourself, as this may result in a fire hazard or electric shock.
report this ad
A The symbol above and on the product means that the product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.The Waste of Electrical and Electronic Equipment (WEEE) Directive has been put in place to recycle products using best available recovery and recycling techniques to minimise the impact on the environment, treat any hazardous substances and avoid the increasing landfill. Contact local authorities for information on the correct disposal of Electrical or Electronic equipment.
[xyz-ips snippet=”download-snippet”]