User Manual
Lezyne 1-HT MPS-V1-R14 LED Light
Model Guide:
This instruction manual covers the operation and care of the Lezyne Super Drive XL, Power Drive XL, and Mini Drive XL LED Light systems. Identify your light model below for further information regarding batteries and mode settings.
Please READ THIS ENTIRE MANUAL before operation in order to ensure proper use and care of your new Lezyne LED Light. Traffic laws mandating lighting vary from country to country. We strongly suggest you inform yourself about lighting laws in the country of intended use.
Overview
Accessories
The following accessories are included with your Lezyne LED Light:
Do It In The Dark:
Adventures in the dark are inherently dangerous activities; it is strongly advised that you to take caution at night. Lezyne LED Lights will greatly improve your visibility, but there are still many dangers. Lezyne recommends for every night adventure that you always perform a few pre-flight checks, which include but are not limited to the following:
- Wearing protective gear
- Dressed in highly visible clothing
- Using a RED rear-facing tail light
- Travelling with proper tools and tire repair
- Light is properly mounted (see MOUNTING)
- Light is properly charged (see CHARGING)
Warnings
- Lezyne LED Lights are meant to be operated in temperatures between -15˚C and 45˚C (5˚F and 113˚F).
- Lezyne LED Lights should only be attached using supplied mounting brackets. DO NOT use Lezyne LED Lights as handheld flashlights.
- DO NOT look directly into light beam, or shine at another person’s eyes.
- Lezyne LED Lights are water resistant under normal conditions, but are NOT waterproof. DO NOT SUBMERGE UNDER WATER. If moisture gets inside light body, remove the Rear Battery Cap and battery, open USB Protective Cover and air-out until completely dry.
- NEVER ATTEMPT TO REMOVE FRONT LENS OR ELECTRONICS. Doing so will void your warranty.
If replacing battery, only use Lezyne branded LIR 18650 2 Amp PROTECTED (part # 4712805977314) or LIR 123A 2 Amp PROTECTED (part # 4712805977321) depending on your model. Make certain (+) positive terminal is inserted into battery housing first. Never attempt to use two (2) LIR 123A batteries in place of one (1) LIR 18650 battery. See CHARGING for instructions on installing battery.
Lezyne USA Inc. and Lezyne Co., Ltd. do not accept any liability for injuries or other damages resulting from the use of this product in any circumstances.
Warranty
In the U.S. and U.K., Lezyne LED Lights carry a two (2) year warranty from the original purchase date to the original owner (proof of purchase is required). This warranty covers materials and manufacturing defects on the LED light housing, electronics, LED, and the mounting bracket supplied. Lezyne Batteries carry a 6-month warranty against any manufacturing defects. Issues not covered by the warranty include normal wear and tear, improper installation, attempted access to electronics, modification of electronices, damage or failure due to accident, misuse, abuse, and / or neglect.
Contact your local dealer or visit www.lezyne.com for complete warranty information and contact information regardingwarranty issues.
For warranty issues outside of the United States, please contact the distributor/retailer for your country or region directly.
Mounting
- Select correct bar clamp for handlebar diameter (25.4mm or 31.8mm).
- Slide clamp over handlebar with bolt hole facing forward, place top mount on clamp, and insert thumbscrew from bottom.
- Tighten thumbscrew until snug; clamp should not rotate on handlebar. DO NOT OVERTIGHTEN.
- Slide LED light into top plate from front and push until body clicks into place.
- To remove LED light, press release tab and pull light forward. Take caution as light body may be warm.
Operation
*Race Mode: With the light off, press and hold the Power Button for five (5) seconds, until the light flashes, then release the button. The light will now enter Race Mode where only Blast and Economy modes are selectable. The light will remain in Race Mode even when turned off. With the light off, press and hold the Power Button for an additional five (5) seconds to return the light to normal mode. Run Times and Modes:
Run Times and Modes
With a fully charged Lezyne battery your Lezyne LED Light will have approximately the following run times and outputs (Lumens = lm).
Battery Monitor: Lezyne LED Lights are equipped with a battery monitor to indicate remaining run time during use. A green and red LED located in the Power Button show the battery status.
Battery Check: When the light is OFF you can check the charge level. Click the Power Button once to display the charge status for 2 seconds. A red LED means you should charge the light before your ride.
Thermal protection circuit: Lezyne LED Lights are protected by a thermal detection system. If the operating temperature of the light gets too high, the light will automatically change to the lowest setting. After five (5) minutes, you will be able to change the light back to the previous mode setting.
Charging
Before using your Lezyne LED Light for the first time, fully charge the battery.
To charge your light:
- Confirm the light is turned off.
- Locate and open USB Protective Cover on bottom of light.
- Insert small end of USB cable into light. Insert other end of cable into powered USB port.
- When charging, green LED will flash.
- If green LED does not flash when plugged in, selected USB port may not be powered. Try another USB port that is powered.
- Light will be fully charged in 4-6 hours, or when green LED becomes solid.
- Remove light from charger and reinstall the USB Protective Cover. Confirm USB Protective Cover is fully installed to Charging assure water tightness.
- If there is a problem with battery, both red and green LEDs Fully charged will light up. Remove/replace battery.
Spare batteries: If you choose to carry extra batteries it is ok to change the batteries at any point during use.
To remove the battery (Power/Super XL ONLY): Begin by unscrewing the Rear Battery Cap. The battery will now be exposed. Move the rear spring by pushing up (1). The spring will now rest on top of the battery (2). Pull the battery out and replace it (3). Replace the Rear Battery Cap and tighten down.
When storing your Lezyne LED Light for long periods of time it is suggested that you remove the battery from the light. Before your next use fully charge the battery.
Water Protection
To ensure water tightness, please note the below images for correct installation of the Rear Battery Cap, USB Protective Cover, and Power Button.
Maintenance
In order to ensure proper function of your light:
- Keep lezyne LED Light clean – keeping mud and debris off of body will improve heat dissipation.
- If lens is dirty, use soft, damp cloth to wipe dirt away.
- Do not use harsh materials or chemicals to clean; these may scratch lens surface.
- Never use hose or high-pressure washer to clean light.
- Always replace Rear Battery Cap and USB Protective Cover correctly to prevent water damage.
More Information
For more information and instructional videos about Lezyne LED Lights, visit: http://lezyne.com/XLledFor Lezyne LED Light accessories and replacement parts, visit: http://magshop.lezyne.com/ledlights/led-extras.html
Lezyne 1-HT MPS-V1-R14 LED Light User Manual – Lezyne 1-HT MPS-V1-R14 LED Light User Manual –
Questions about your Manual? Post in the comments!
[xyz-ips snippet=”download-snippet”]