1141 WALL BUTTON TRANSMITTERInstallation Guide
Figure 1:1141 Wireless Wall Button
DESCRIPTION
The 1141 Wall Button is a one-button wireless transmitter. The transmitter may be used for a variety of applications such as arming, disarming, toggling an output, activating a Z-Wave favorite, or activating a panic or emergency alarm. 1141 features a water-resistant button (when installed with double-sided tape) with a status LED. Double-sided tape is not included. If activated in programming, the LED provides a visual indication that a message has been transmitted and received by the panel. 1141 receives power from two supplied 3.0 V lithium batteries.Compatibility
- All 1100 Series Wireless Receivers and panels with built-In 1100 Series Wireless ReceiversWhat is Included?
- One 1141 Wall Button Transmitter
- Two batteries (3.0 V lithium CR2430)
- Hardware pack
PROGRAM THE PANEL
Refer to the panel programming guide as needed. After completing each of the following steps, press CMD to advance to the next prompt.
- At a keypad, enter 6653 (PROG) to access the Programmer Menu.
- At ZONE INFORMATION, enter the wireless zone number.
- At *UNUSED*, enter the zone name.
- At ZONE TYPE, press any Select key or area and select the zone type.
- At the NEXT ZN? prompt, select NO.
- When WIRELESS? displays, select YES.
- At SERIAL#, enter the eight-digit device serial number.
- At SUPRVSN TIME, enter a supervision time. Default is 240.
- At LED OPER, select one of the following options:• YES: The LED blinks when the button is pressed, then once every second for five minutes to confirm that a message was sent• NO: The LED blinks once when the button is pressed to confirm that a message was sent
- At the NEXT ZN? prompt, select YES if you are finished programming the zone. Select NO if you would like to access additional programming options.
- To save panel programming, go to STOP and press CMD.
INSTALL THE BATTERY
Refer to Figures 2, 3, and 4 during battery installation.
- Open 1141 by inserting a small flathead screwdriver in the tab.
- Gently pull upward on the screwdriver handle until the housing completely opens.
- Press the top and bottom PCB snaps and carefully lift the bottom of the PCB out of the housing. Do not disassemble the button and gasket from the top housing.
- Observing polarity, insert the included batteries into the holder and press them into place.
- Insert the bottom of the PCB into the bottom PCB snap.
- Lift up the top PCB snap and press the PCB into place. Do not snap the transmitter cover back onto the base until after mounting 1141.
A) PCB SupportsB) PCB SnapsC) Serial Number LabelD) Housing Tab
Figure 3: Top Cover Interior Details
SELECT A LOCATION
1141 provides a Survey LED capability to allow one person to confirm communication with the wireless receiver or panel while the cover is removed.
- With the cover removed, hold the transmitter in the desired location.
- Press the button to send data to the panel and determine if communication is confirmed or faulty.
Confirmed: If communication is confirmed, for each press or release of the button, the LED blinks immediately on and immediately off. Repeat this test to confirm five separate consecutive LED blinks. Any indication otherwise means proper communication has not been established.Faulty: If communication is faulty, the LED remains on for about 8 seconds or flashes multiple times in quick succession. Relocate the transmitter or receiver until the LED confirms clear communication.
MOUNT THE TRANSMITTER
When mounting 1141, refer to Figure 5 for mounting hole locations. For simpler mounting or waterproof installations, use double-sided tape. Refer to Figure 6. To mount 1141 with the included screws, complete the following steps.
- With the cover removed, place the two supplied Phillips head screws into the mounting holes.
- Secure the housing base to the surface.
- Snap the transmitter cover back onto the base.
1141 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS
TEST THE TRANSMITTER
After 1141 has been installed, test to confirm that it is communicating reliably with the panel. Use the Tech APP™ to perform a Wireless Walk Test on the system or follow these steps to perform a Walk Test from a keypad that is connected to the panel:
- At the keypad, enter 8144 (WALK) and select WLS.
- If the transmitter fails to check-in at the keypad, ensure that it is wired properly and check for sources of interference such as metal objects and electronic equipment.
ADDITIONAL INFORMATION
Replace the BatteriesUse 3.0 V lithium batteries, like DMP Model CR2430, or equivalent retail models. Refer to Section 2 for battery installation instructions. Properly dispose of all used batteries.
Sensor Reset to Clear LOBAT
- Once the battery is replaced, a sensor reset is required at the keypad to clear the LOBAT message.
- On an LCD keypad, press and hold 2 for two seconds. On a graphic touchscreen keypad, press RESET. Enter your user code, if required. The keypad displays SENSORS OFF followed by SENSORS ON.
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons. It must not be located or operated in conjunction with any other antenna or transmitter.Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA INFORMATION
This device complies with Industry Canada Licence-exempt RSS standards. Operation is subject to the following two conditions:
- This device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a generalbystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits.1141 WALL BUTTONTRANSMITTER
Specifications
| Battery | |
| Life Expectancy | 4 years (normal operation) |
| Type | 3.0 V lithium CR2430 |
| Frequency Range | 905-924 MHz |
| Button Press | |
| Time to Activate | 1/8 sec. (0.125 sec.) |
| Dimensions | |
| Transmitter Case | 3” H x 2-1/2” W x 1/2” D |
| Color | White |
| Housing Material | Flame retardant ABS |
Designed, engineered, and manufactured in Springfield, MO using the U.S. and global components.LT-1326 20164
Ordering Information1141-W Wireless Wall Button Transmitter
AccessoriesCR2430/10 3 V lithium coin cell battery, 10 pack
CompatibilityAll 1100 Series Wireless Receivers and panels with built-In1100 Series Wireless Receivers
PatentsU. S. Patent No. 7,239,236
report this adCertificationsFCC Part 15 Registration ID CCKPC0155Industry Canada Registration ID 5251A-PC0155
INTRUSION • FIRE • ACCESS • NETWORKS2500 North Partnership BoulevardSpringfield, Missouri 65803-8877800.641.4282 | DMP.com
References
[xyz-ips snippet=”download-snippet”]