REMINGTON AS1220 Amaze Smooth and Volume Air Styler User Manual
Thank you for buying your new Remington® product. Please read these instructions carefully and keep them safe. Remove all packaging before use.
IMPORTANT SAFEGUARDS
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised/instructed and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised. Keep the appliance and cable out of reach of children under 8 years.
Do not use this appliance near bathtubs, showers, basins or other vessels containing water.- When the appliance is used in a bathroom, unplug it after use since the proximity of water presents a hazard even when the appliance is switched off.
- For additional protection, the installation of a residual current device (RCD) having a rated residual operating current not exceeding 30 mA is advisable in the electrical circuit supplying the bathroom*.
- Currently, the fitting in a bathroom of an electrical socket suitable or capable of operating the appliance is not permitted in the UK (see BS7671).
- If the supply cord of this unit becomes damaged, discontinue use immediately and return the appliance to your nearest authorised Remington® service dealer for repair or replacement in order to avoid a hazard.
- Always ensure the voltage to be used corresponds to the voltage stated on the unit before plugging the appliance into the mains socket.
- Keep direct airflow away from eyes or other sensitive areas.
- Do not allow any part of the appliance touch the face, neck or scalp.
- During use, always ensure the inlet and outlet grilles are not blocked in any way as this will cause the unit to automatically stop. If this should occur, switch off and allow the unit to cool.
- Keep the power plug and cord away from heated surfaces.
- Do not leave the appliance unattended while plugged in.
- Do not place the appliance on any soft furnishings.
- Do not use attachments other than those we supply.
- Do not set the appliance down while still on.
- Do not twist or kink the cable, or wrap it round the appliance.
- Do not use the appliance if it is damaged or malfunctions.
- Check the cord regularly for any sign damage.
- Let the attachments cool before removing.
- This appliance is not intended for commercial or salon use.
PARTS
- 1200W power handle
- 21mm thermal bristle brush
- 30mm retractable bristle curling brush
- Root boost attachment
- Paddle brush
- Concentrator
- Speed/heats setting switch
- Attachment release switch
- Storage case (not shown)
- 3m salon length swivel cord
INSTRUCTIONS FOR USE
- Wash and condition your hair as normal.
- Squeeze out excess moisture with a towel and comb through.Hairsprays contain flammable material – do not use while using this product.
- Select your attachment before you turn on the appliance.
- Attachments can be connected by aligning the arrows on the attachment and the handle, gently pushing the attachment onto the handle and turning to ‘click’ into place.
- Plug the product into the mains power supply.
- To turn the product on slide the speed/heat setting switch to position ‘1’.
- Dry roots completely and dry length 90% dry, ready for styling.
- To dry hair use the concentrator attachment.
- Section the hair prior to styling. Style the lower layers first.
- Select the desired temperature and speed setting using the switch on the handle.
- To increase the setting slide the heat/speed setting switch to position ‘2’.
Root Boost AttachmentThis is designed to create voluminous hair at the roots while it dries Push the root boost slowly into your roots towards the centre of your head whilst drying it. Allow the hair to push against the root boost. Lift the root boost up pulling hair at a right angle to your head whilst drying. Repeat until you have dry, voluminous hair.
Paddle Brush AttachmentThis attachment is to create Salon straight hair. Simply brush through your hair slowly with the paddle brush, just like you would with a normal brush.Tip – You can add some volume and bounce if you tip your head upside down and do the underneath of your hair. Then use your fingers to shape the hair and ends.
Bristle Brush Attachments
- For all brush attachments: Take a section of hair and place the ends around the brush. Rotate the styler allowing the hair to wrap around the barrel of the brush drying and styling as you go.
- Use the 21mm thermal bristle brush for waves and smoother ends.
- Use the 30mm retractable bristle brush for firmer curls and waves.
- Let the hair cool before styling.
- Let the attachments cool before removing.
- To remove attachments, press the attachment release button and pull the attachment away from the main housing.
- After use, turn the appliance off and unplug.
- Let the appliance cool before cleaning and storing away.
Cool shot
- To set your style and add shine use the cool shot function. To operate slide the heat/ speed setting switch to position ‘f’. Slide back to turn off.
- Let the attachments cool before removing.
- After use, turn the appliance off and unplug.
- Let the appliance cool before cleaning and storing away.
CLEANING AND MAINTENANCE
- Unplug the appliance and allow to cool.
- To maintain peak product performance and to prolong motor life, it is important to regularly remove any dust and dirt from the air filter grille and clean with a soft brush.
- Wipe all the surfaces with a damp cloth.
- Don’t use harsh or abrasive cleaning agents or solvents.
RECYCLING
report this adTo avoid environmental and health problems due to hazardous substances, appliances and rechargeable and non-rechargeable batteries marked with one of these symbols must not be disposed of with unsorted municipal waste. Always dispose of electrical and electronic products and, where applicable, rechargeable and non-rechargeable batteries, at an appropriate official recycling/ collection point.
References
[xyz-ips snippet=”download-snippet”]