Skullcandy Air Raid Wireless User Manual

USER MANUAL

Air Raid WirelessSkullcandy

Diagram

Main Speaker Controls

Power On / Off

Power OnFlip the power switch up. Wait (for up to 5 seconds) for the LED light to turn magenta and the power on tone to be played. Do not press any other buttons during this time. When Air Raid is on, the green battery LEDs will lash for 2 seconds to show the battery level. The speaker will look to connect to up to 2 devices in the paired device list. It no paired devices are available for connection, the speaker will enter pairing mode.

Power OffFlip the power switch down. As the speaker powers off, it will play the power down tone and the LED will turn magenta. It is recommended to disconnect all Bluetooth streaming devices before powering off.

Enter Pairing Mode

When the speaker is ON, press and hold the center button for 5 seconds. The LED will flash red and blue alternating when pairing mode is entered. When a device is successfully paired, the LED will blink red 3 times.

Pairing New Device

Connect to DeviceWhen the speaker is not connected to a device and not in pairing mode, short press the center button to attempt to connect to a device from the list of paired devices. Ensure the device Bluetooth is ON. When the device is connected, the LED will flash blue once every 5 seconds.

Clearing the Pairing ListTo clear the list of paired devices from the speaker, push and hold the -F and center buttons simultaneously for 3 seconds while the power is ON. This will reset the speaker to default pairing mode the next time it is powered on. Devices will need to be paired again once this has been done, even if previously paired.

Battery Status CheckWhen the device is ON, double press the center button to show the green battery life LED on the left side of the speaker. Three LEDs indicate the battery life is 50%-100%, two LEDs indicates 15%-50%, and one LED indicates 0%-15% battery life left.

Charging

Plug the included micro USB to AC adapter into the speaker and a wall outlet. Charging will begin per the Charging Status below. A micro USB to USB cable (not included) can also be used to charge the speaker from a powered USB port.

Charging StatusAt any time when the speaker is charging, the three green battery indication LEDs will flash on and off to signal the device is charging. When the device is finished charging, all three LEDs will turn off.

Music Controls

Music Play / Pause

Start Music PlaybackWhen the speaker is connected to the device but not streaming music, short press the center button to start streaming. When the device is streaming, the front LED will be off.

Pause Music PlaybackWhen the speaker is streaming music, short press the center button to pause the playback. Volume Up When the speaker is ON and not in pairing mode, press the + button to increase the volume level.

Volume Up

When the speaker is ON and not in pairing mode, press the button to increase the volume level.

Volume Down

When the speaker is ON and not in pairing mode, press the – button to decrease the volume level.

Track Forward

When the speaker is connected to a device, short press the + and center buttons simultaneously to track forward.

Track Backward

When the speaker is connected to a device, short press the – and center buttons simultaneously to track backward.

3.5 mm Wired Audio PlaybackWhen the device is not streaming via Bluetooth, plug in a 3.5mm cable (not included) into the rear AUX jack. To play music through the wired connection, you must control playback from the source device. Track controls on the speaker will be disabled. Volume controls will function normally. Note that Bluetooth streaming takes priority over wired audio playback.

Other Device Features

Auto Power OffIf the device is idle for 5 minutes, it will turn itself off while the switch is in the on state. To turn the speaker back ON, flip the switch to off position then to on again.

Auto LED OffThe LED will be powered off after 4.5 minutes for every state. This feature is to conserve battery life. For example, if the BT speaker is at music streaming state for 4.5 minutes, the LED will auto off. The timer will reset whenever there is a change in state. One exception is that the LED indication for pairing mode will remain active during pairing mode as paring mode itself has a timeout.

Multipoint Support

The speaker supports connecting to up to TWO audio source devices at the same time. At any one time, only one device’s audio will be heard through the speaker. When using the play/pause button on the speaker, the play/pause command will always go to the last streaming device. To switch the playback device, the user has to pause/stop the playback on the currently streaming device and must start the playback from the other device directly. Once the playback is established with the new device the use of play/pause command will function for that device.

Troubleshooting

Device doesn’t charge while playing music at maximum volume…

This may occur due to limitations in the charging capabilities. At maximum volume the amplifier can draw more power than it is possible for the micro USB connecter to provide. There may be times where the device is plugged in, but the battery is still slowly being drained. The solution is to turn down the volume until the green charging indicators begin to flash consistently.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Questions about your Manual? Post in the comments!