Avenue Silence
manual
Overview
- +
- Bluetooth
- –
- Status LED
- Charging Port
- Microphone
- NC
- AIX in
- NC LCD
Specifications
Bluetooth version: 40Impedant: 320Sensitivity: 1053 dBListening frequency: 20 Hz – 20 kHzCancellation frequency: 0 Hz – 500 HzCancellation: 20 dBCharging input: 5V, 220 mACharge time: 3hBattery time: Up to 16 h (12 with NC active)Charging cable: Micro USBCharging cable length: 100 cmAudio cable length: 125 cmWeight: 238gFrequency Range: 2402MHz-2480 MHzEffective Radiated Power: 3.78 dBm
Use
Power on/offTo turn on the headphones, press and hold the Bluetooth button (2) until the Status LED (4) blinks blue. Press and hold the Bluetooth button again until the Status LED blinks red. The headphones are now turned off. To start the noise cancellation, slide the NC button (7) up. The NC LED (9) will light up in green. To turn off the noise cancellation, slide the NC button down. The NC LED will turn off.
ChargingConnect the USB cable to the charging port (5) and a computer or a USB power adapter. The LED will shine red during charging and turn blue when the battery is fully charged. The LED will flash red if the battery level is low. Note: The headphones will reset when connected to a charging source.
PairingMake sure the headphones are turned off. Press and hold the Bluetooth button (2) for 5 seconds to enter pairing mode. The Status LED (4) will blink blue and red. Turn on bluetooth on your device and search for “Avenue Silence”(90300) or “Roxcore ANC”(97900), select it when found. If necessary, enter the passcode, “0000”, to pair and connect the headphones. Some devices also ask to confirm the headset connection after pairing. The Status LED will blink blue and a voice will say “connected” after the pairing is successful. If no bluetooth devices are paired within 15 minutes the headphones will turn off.
General functionsChange the volume with the + & – buttons (1 & 3). You can also skip to the next track or go to the previous by holding in the corresponding button. Play or pause the current track by pressing the Bluetooth button (2). To answer or end a call, press the bluetooth button. Press and hold it for at least 2 seconds to reject an incoming call. Doubleclick it to redial the last call.Note: The functions of the buttons may not always be the same for all devices and brands.
Multifunction buttonThere is a multifunction button on the included 3.5 mm audio cable. You can use this to answer incoming calls or manage music. Make sure the headphones are turned off before connecting the cable. Connect the end with the headphone symbol to the headphones and the other end to your device. During an incoming call press it once to answer or press and hold for 2 seconds to reject the call. Press it once during an ongoing call to hang up. When playing music press once to play or pause a track, dou bleclick to go forward to the next track. Tripleclick to go to the start of a track or jump two tracks forward depending on phone model. There is also a microphone situated near the multifunction button that can be used during phone calls.Note: You must turn the headphones off and on before connecting the cable if the bluetooth mode has been activated. The functions of the button may not always be the same for all devices and brands. If the battery is depleted the noise cancellation must be turned off if you want to use the 3.5 mm audio cable.
Note! This product contains a rechargeable Li-ion battery and the battery can not be replaced. To prevent possible hearing damage, do not listen at high volume levels for long periods. If you encounter any problems with the manual, please go to www.kjell.com/97900, 90300 for an updated version.
Simplified EU Declaration of ConformityKjell & Company hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of the EU declaration of conformity is available at www.kjell.com/97900, 90300
[xyz-ips snippet=”download-snippet”]