Fly KillerInstruction manual
ModelFD499
Safety Tips
- A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.
- Consult Local and National Standards to comply with the following:– Health and Safety at Work Legislation– BS EN Codes of Practice– Fire Precautions– IEE Wiring Regulations– Building Regulations
- Always switch off and disconnect the power supply to the appliance before cleaning.
- Install the appliance out of the reach of children.
- Never insert hands or other objects into the appliance while it is connected to the power supply.
- Install the Fly Killer at least 1 meter away from food preparation areas.
- Never use near flammable objects.
- For INDOOR use only.
- Keep all packaging away from children. Dispose of the packaging in accordance with the regulations of local authorities.
- If the power cord is damaged, it must be replaced by an Nisbets Essentials agent or a recommended qualified technician in order to avoid a hazard.
- Nisbets Essentials recommends that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to Visual Inspection, Polarity Test, Earth Continuity, Insulation Continuity, and Functional Testing.
- Danger – High voltage!
- The appliance emits UV radiation. Do not stare at the light.
- The appliance is not to be used in locations where flammable vapor or explosive dust is likely to exist.
- Do not use in barns, stables, and similar locations.
- Nisbets Essentials recommend that this product be connected to a circuit protected by an appropriate RCD (Residual Current Device).
Introduction
Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your Nisbets Essentials product.
Pack Contents
The following is included:
- Fly Killer
- Instruction manual
- Hanging chain
Nisbets Essentials prides itself on quality and service, ensuring that at the time of packaging the contents are supplied fully functional and free of damage.Should you find any damage as a result of transit, please contact your Nisbets Essentials dealer immediately.
Installation
Note: Ensure the mounting substrate and the fixings used can support the weight of the appliance. If in doubt seek professional advice or assistance.
- Remove all packaging and protective film from the Fly Killer.
Note: Close proximity to other light sources such as skylights and windows will reduce the effectiveness of the Fly Killer. - For best results, locate the Fly Killer in the darkest part of the room, but at least 1 meter away from food preparation areas.
- Connect the appliance to mains power.
Operation
WARNING: Under no circumstances should hands be placed anywhere near the high voltage grid when the appliance is operational. |
The fly killer works by luring insects onto an electrified metal grid using ultra-violet light. It uses no chemicals and is pollution-free. To use the FlyKiller:
- Press the switch to the ON (I) position. Ensure it is set to OFF (O) before plugging into mains.
- The light will come on and the grid will become electrically charged.
Cleaning, Care & Maintenance
Always switch off the power and disconnect the appliance from the power supply before cleaning. |
- Clean the collection tray regularly with warm soapy water.
- DO NOT immerse the appliance in water. Wipe the safety guard and external casing with a damp cloth.
- Change the bulbs every 9 months.
Changing the Bulb
WARNING: Always turn Off the appliance and disconnect from the power supply before changing thebulb. |
- Remove the collection tray.
- Lay the appliance face down.
- Unscrew the two screws holding the safety guard at the rear of the Fly Killer [Fig. 1].
- Lift up the guard rail [Fig. 2].
- Holding the ends of the bulb, twist it ‘forwards’ in its socket until it clicks [Fig. 3].
- Slide the bulb up out of its sockets [Fig. 4].
- Replace with a new bulb.
- Twist the new bulb ‘backward to lock it back in place.
- Replace the guard rail and the two screws.
Troubleshooting
Fault | Probable Cause |
Solution |
The appliance is not working | The unit is not switched on | Check the unit is plugged in correctly and switched on |
Plug and lead are damaged | Call Nisbets Essentials agent or qualified Technician | |
Fuse in the plug has blown | Replace the plug fuse | |
Power supply | Check power supply | |
Internal wiring fault | Call Nisbets Essentials agent or qualified technician | |
Tube has expired | Refer to the ‘Changing the Bulb’ section | |
Tube is faulty or has not been fitted correctly |
Technical Specifications
Model |
Voltage | Power | Dimensionsh x w x d (mm) |
Weight |
FD499 |
220-240V-, 50Hz | 23W | 272 x 350 x 86 |
2.56kg |
Electrical Wiring
This appliance is supplied with a 3 pin BS1363 plug and lead.The plug is to be connected to a suitable mains socket.This appliance is wired as follows:
- Live wire (colored brown) to the terminal marked L
- Neutral wire (colored blue) to the terminal marked N
- Earth wire (colored green/yellow) to terminal marked E
This appliance must be earthed.If in doubt consult a qualified electrician. |
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required, they must be readily accessible.
Compliance
The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/ or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area. |
Nisbets Essentials parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.Nisbets Essentials products have been approved to carry the following symbol: |
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Nisbets Essentials.Every effort is made to ensure all details are correct at the time of going to press, however, Nisbets Essentials reserves the right to change specifications without notice.
DECLARATION OF CONFORMITY
- Conformiteitsverklaring
Equipment Type |
Model |
|
Flykiller |
FD499 (& -E -A) |
|
Application of Territory Legislation & Council Directives(s)Toepassing van EuropeseRichtlijn | Low Voltage Directive (LVD) – 2014/35/EU EN 60335-1:2012 +A11:2014EN 60335-2-59:2003 +A1:2006 +A2:2009 EN62233:2008Electro-Magnetic Compatibility (EMC)Directive 2014/30/EU – recast of 2004/108/EC EN55014-1:2017EN 55014-2:2015 EN 61000-3-3:2013 EN 61000-3-2:2014Restriction of Hazardous Substances Directive (RoHS) 2015/863 amending Annex II to Directive 2011/65/EU | Electrical SafetyEN 60335-1:2012 +A11:2014EN 60335-2-59:2003 +A1:2006 +A2:2009 EN 62233:2008Electromagnetic CompatibilityEN 55014-1:2017 EN 55014-2:2015 EN 61000-3-2: 2014 EN 61000-3-3: 2013 |
Producer Name | Nisbets Essentials |
I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s) and Standard(s).Date Signature • Handtekening • Signature • Unterschrift Firma • Firma • AssinaturaFull NamePositionProducer Address
4th December 2020 | ||
Ashley Hooper | Eoghan Donnellan | Josie Holt |
Technical & QualityManager | CommercialManager/ Importer | Commercial Manager/ ResponsibleSupplier |
Fourth Way, Avonmouth,Bristol,BS11 8TBUnited Kingdom | 42 North PointBusiness Park New Mallow RoadCork Ireland | 15 Bagdally Road, CampbelltownNSW 2560 |
UK | +44 (0)845 146 2887 |
Eire | |
NL | 040 — 2628080 |
FR | 01 60 34 28 80 |
BE-NL | 0800-29129 |
BE-FR | 0800-29229 |
DE | 0800 — 1860806 |
IT | N/A |
ES | 901-100 133 |
PT | vendasOnisbets.pt |
FD499_ML_A5_v1_20201217
References
[xyz-ips snippet=”download-snippet”]