ES-LV9U Rechargeable Shaver
Operating Instructions (Household use) Rechargeable ShaverModel No. ESLV9UEnglish 3 29 59 87
2
English
Operating Instructions (Household use) Rechargeable ShaverModel No. ESLV9U
Contents
Safety precautions………………… 4 Important information 9 Parts identification 11 Preparation 12 How to use 14 Cleaning thoroughly17 Replacing the system outer foil and the inner blades 19
Replacing the cleaning liquid20 When the LOW/STATUS lamp glows21 FAQ 22 Troubleshooting 22 Battery life 27 Removing the built-in rechargeable battery 27 Specifications 28
Thank you for purchasing this Panasonic product. Before operating this unit, please read these instructions completely and save them for future use3
English
Safety precautions
WARNING
Make sure to follow these instructions.
To prevent accidents, injuries or damage to property,please follow the instructions below.The following chart indicates the degree of damage caused by improper operation
DANGER
Indicates a potential hazard that will result in serious injury or death.
Indicates a potential hazard thatWARNING could result in serious injury ordeath.Indicates a potential hazard thatCAUTION could result in minor injury orproperty damage.The symbols are classified and explained as follows
This product This product has a built-in rechargeable battery. Do not throw into fire, apply heat, or charge, use, or leave in a high temperature environment Doing so may cause overheating, ignition, or explosion.Do not modify or repair Doing so may cause fire, electric shock, or injury. Contact an authorized service centre for repair (replacement of battery etc).Never disassemble except when disposing of the product Doing so may cause fire, electric shock, or injury.
This symbol indicates prohibition.
This symbol indicates requirement that must be followed.
4
WARNINGIn case of an abnormality or malfunction Immediately stop using and remove the AC adaptor if there is an abnormality or malfunction Failure to do so may cause fire, electric shock, or injury. <Abnormality or malfunction cases> · The main unit, self-cleaning recharger, AC adaptor or cord is deformed or abnormally hot · The main unit, self-cleaning recharger, adaptor or cord smells of burning · There is an abnormal sound during use or charging of the main unit or self-cleaning recharger Immediately request inspection or repair at an authorized service centre.Power supply Do not connect or disconnect the adaptor to a household outlet with a wet hand Doing so may cause electric shock or injury.
Do not immerse the AC adaptor and the selfcleaning recharger in water or wash with water Do not place the AC adaptor and the selfcleaning recharger over or near water filled sink or bathtub Never use the appliance if the AC adaptor is damaged or if the power plug fits loosely in a household outlet Do not damage the cord or the power plug · Do not deface, modify, forcefully bend orpull the cord or the power plug Also, do not place anything heavy on, twist or pinch the cord Doing so may cause electric shock or fire due to a short circuit.Do not use in a way that would exceed the rating of the household outlet or the wiring Exceeding the rating by connecting too many plugs to one household outlet may cause fire due to overheating.Do not use anything other than the supplied AC adaptor and the self-cleaning recharger for any purpose Also, do not use any other product with the supplied AC adaptor and the self-cleaning recharger (See page 11) Doing so may cause burn or fire due to a short circuit.Fully insert the power plug Failure to do so may cause fire or electric shock.5
English
English
WARNINGDisconnect the AC adaptor when cleaning the main body with water Failure to do so may cause electric shock or injury.Regularly clean the power plug and the appliance plug to prevent dust from accumulating Failure to do so may cause fire due to insulation failure caused by humidity.Preventing accidents Persons using an implanted medical electronic device, such as a pacemaker, should not allow this unit to touch the skin where the medical electronic device is implanted Doing so may cause an accident or illness.Do not place within reach of children or infants Do not let them use it Putting parts or accessories in the mouth may cause an accident or injury.Do not use or store the self-cleaning recharger on top of other electrical devices Doing so may cause electric shock due to liquid spill or fire due to a short circuit.
If detergent or oil is consumed accidentally, do not induce vomiting, drink a large amount of water and contact a physician If detergent or oil comes into contact with eyes, wash immediately and thoroughly with running water and contact a physician Failure to follow these instructions may result in physical problems.If detergent contacts skin, wash immediately and thoroughly with soap If you experience skin irritation anywhere on the body, stop using immediately and contact a physician Failure to follow these instructions may result in physical injury or injury to the skin.Note the following precautions This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Failure to do so may cause an accident or injury.
6
WARNINGThe supply cord cannot be replaced If the cord is damaged, the AC adaptor should be scrapped Failure to do so may cause an accident or injury.CAUTIONProtecting the skin Do not use excessive pressure to apply the system outer foil to your lip or other part of your face Do not apply the system outer foil directly to blemishes or injured skin Do not touch the blade section (metallic section) of the inner blade Doing so may cause injury to skin or hand.Do not forcefully press the system outer foil Also, do not touch the system outer foil with fingers or nails when in use. Do not use this product for hair on head or any other part of the body Doing so may cause injury to skin or reduce the life of the system outer foil.Do not remove the shaver from the selfcleaning recharger while using the “AUTO” mode or “Dry/Charge” mode Doing so may cause burn due to high temperatures around the system outer foil.
Check the system outer foil for cracks or deformations before use Failure to do so may cause injury to the skin.Note the following precautions Do not allow metal objects or trash to adhere to the power plug or the appliance plug Doing so may cause electric shock or fire due to a short circuit. Do not share your shaver with your family or other people Doing so may result in infection or inflammation. Do not use detergent for any purpose other than washing the shaver blades Using it with other products may cause discoloration or cracking. Disconnect the adaptor from the household outlet when not charging Failure to do so may cause electric shock or fire due to electrical leakage resulting from insulation deterioration. Use caution when opening detergent as spout is sharp Failure to do so may cause injury.7
English
English
Handling of the removed battery when disposingDANGER· The rechargeable battery is exclusively for use with this appliance Do not use the battery with other products · Do not charge the battery after it has been removed from the product · Do not throw into fire or apply heat. · Do not hit, disassemble, modify, or puncture with a nail · Do not let the positive and negative terminals of the battery get in contact with each other through metallic objects · Do not carry or store the battery together with metallic jewellery such as necklaces and hairpins · Do not use or leave the battery where it will be exposed to high temperatures, such as under direct sunlight or near other sources of heat · Never peel off the tube Doing so may cause overheating, ignition, or explosion.
WARNINGAfter removing the rechargeable battery, do not keep it within reach of children and infants The battery will harm the body if accidentally swallowed. If this happens, consult a physician immediately.If the battery fluid leaks out and comes in contact with the eyes, do not rub the eyes, and thoroughly rinse with clean water, such as tap water Failure to do so may cause eye injury. Consult a physician immediately.CAUTIONIf the battery fluid leaks out and comes in contact with the skin or clothes, rinse off with clean water, such as tap water Failure to do so may cause inflammation.
8
English
Important information· This WET/DRY shaver can be used for wet shaving using shaving lather or for dry shaving. You can use this watertight shaver in the shower and clean with water. The following symbol means suitable for use in a bath or shower.· Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic WET/DRY shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method.· Keep both the inner blades inserted. If only one of the inner blades is inserted, the shaver may be damaged.· If you clean the shaver with water, do not use salt water or hot water. Do not soak the shaver in water for a long period of time.· The following symbol indicates that a specific detachable power supply unit is required for connecting the electrical appliance to the supply mains. The type reference of power supply unit is marked near the symbol.· Charge the appliance correctly according to these Operating Instructions. (See page 12 “Charging the shaver”.)
· This appliance contains battery that is only replaceable by skilled persons. Please contact an authorized service centre for the details of repair.Note the following precautionsWhen using · Do not bring the system outer foil into contact withhard objects. Doing so may damage the system outer foil as it is very thin and deforms easily. · Do not drop or hit against other objects. Doing so may cause injury.About detergent · Do not leave the detergent in location of hightemperatures. Doing so may cause deterioration. · Immediately wipe up any cleaning liquid that has been spilt. Prolonged contact may cause discoloration of leather products or wooden floors.When storing · Store the shaver in a place with low humidity afteruse. Failure to do so may cause malfunction due to condensation or rust. · Be sure to place the protective cap on the shaver when carrying around or storing. Failure to do so may cause injury to skin or reduce the life of the system outer foil.
9
English
When cleaning · Do not dry the main unit with a dryer or a fan heater.Doing so may cause malfunction or deformation of the parts. · Do not leave the shaver exposed to direct sunlight with the foil frame detached. Doing so may deteriorate the waterproof rubber and degrade waterproof function, which may cause to malfunction.10
English
Parts identification
A
7
6 c
BBack
a b d
C
E
DF
A Main body Protective cap System outer foil Foil frame Smooth rollers · They help to glide over the skin more easily. Foil frame release buttons 6 Power switch 7 Lamp display a. Shaving sensor lamp ( ) b. Battery capacity lamp
c. Switch lock lamp
Cleaning liquid unit
()
removal button
d. Charge status lamp Intake port
()
Selfcleaning
Appliance socket
recharger socket
Outer foil section
Lock release lever
System outer foil
Cleaning liquid filter
release buttons
Cleaning liquid unit
Inner blades
STATUS lamp
Trimmer
LOW lamp
Trimmer handle
CLEAN lamp
Main body rear
DRY lamp
terminals
SELECT button
B Self-cleaning recharger C AC adaptor (RE7-87)
(RC9-25)
Adaptor
Charging terminals
Power plug
Cord
Appliance plug Accessories D Travel case E Oil F Special detergent(Detergent)There may be water droplets inside the self cleaning recharger at the time of purchase, but there is no problem regarding the hygiene. They are remains after the factory inspection.11
Preparation
While charging
After charging is completed
English
Charging the shaver
· Turn the shaver off.
· Wipe off any water droplets on the main body rear
terminals.
1 Insert the appliance plug
into the self-cleaning
2
recharger
2 Remove the protective cap
3
while pressing the side of
the cap and insert the
1
shaver into the self-
cleaning recharger
· Slowly insert the shaver into
the selfcleaning recharger
taking care not to damage the
system outer foil.
3 Plug the adaptor into a household outlet · Check that the charge status lamp ( ) is glowing. · Charging is completed after approx. 1 hour.4 Disconnect the adaptor after charging iscompleted
Quick charge Even though the battery runs out, you can shave once after 3minute charge. (This will differ depending on usage.)
glows. The number of the battery capacity lamp will increase as charging progresses.
All the battery capacity lamp and will glow and then turn off after 5 seconds.
Notes · When charging the shaver for the first time or when ithas not been in use for more than 6 months, the charging time may change or the charge status lamp ( ) may not glow for a few minutes. It will eventually glow if kept connected. · Recommended ambient temperature for charging is 10 °C 35 °C. It may take longer to charge, or the charge status lamp ( ) will blink quickly and the battery may fail to charge properly in extremely high or low temperatures. · The shaver can be used for approximately 2 weeks with a full charge. (Based on one 3minute dryshave usage per day in an ambient temperature range of 20 °C 30 °C.) The number of usable days varies depending on the following conditions. Beard thickness Pressure applied to the skin Usage frequency of the sonic vibration cleaning mode
12
English
· If there is noise from the radio or other sources while using or charging the appliance, move to a different location to use the appliance.
Charging without the self-cleaning recharger
· Turn the shaver off.
· Wipe off any water droplets on the appliance socket.
1 Insert the appliance plug
into the shaver
2 Plug the adaptor into a
2
household outlet
3 Disconnect the adaptor
after charging is completed 1
Note You cannot operate the shaver while charging.Preparing the cleaning liquidCleaning can start right after the usage by preparing in advance. (See page 16.) · Remove the AC adaptor from the selfcleaning recharger.
1 Press the cleaning
liquid unit removal
button () and
remove the cleaning
liquid unit () on a hard, flat surface.
· When the selfcleaning recharger is lifted, or on
the soft surface such as carpets, the lock release
lever will not fit in the recharger properly. In that case, the cleaning liquid unit cannot be removed.
2 Pour tap water ()
and detergent ()
into the cleaning
liquid unit
· Be careful not to let the
water rise above the
maximum water line ().
· Pour the entire packet
of detergent.
3 Slowly insert thecleaning liquid unit into the selfcleaning recharger until it clicks
13
English
Notes · To replace the cleaning liquid, see page 20. · Only use selfcleaning recharger detergent forPanasonic shavers. Not doing so may cause malfunction or failure. · Do not tilt the selfcleaning recharger. Doing so may cause spill or the number of days that cleaning liquid can be used reduce. · You can use the cleaning liquid for approximately 30 days if used once per day. (This will differ depending on beard thickness and the ambient temperature.)How to use
Tips for better shavingApply the whole system outer foil perpendicularly against the skin and shave by slowly gliding the shaver over the face against the grain of the beard. · The beard under the chin andaround the throat can be shaved better by stretching the skin so the beard will stand. · To prevent damaging the system outer foil, do not shave with only a part of the system outer foil.
Shaving beard1 Press and shave · The “shaving sensor”, which automatically adjusts the power depending on the beard thickness, will operate. It will shave with high power on areas where the beard is heavy, and reduce the power on areas where the beard is thin, to reduce burden on the skin.
2 Press when finished.
14
English
While using
After use
The remaining battery capacity are shown and then turn off after 5 seconds. · Approximate amount ofbattery capacity is displayed as 20 100. · The shaving sensor lamp ( ) blinks.
The remaining battery capacity blink and then turn off after 5 seconds.
When the battery capacity is low “20” blinks when operating the shaver. · You can shave 2 to 3 times after “20” blinks.(This will differ depending on usage.)
Notes · The appliance may not operate in an ambienttemperature lower than approximately 5 °C. · The shaving sensor may not respond depending onthe type and quantity of the shaving gel. This is not abnormal.
· Depending on the beard thickness or the amount of beard trimmings in the shaver head, the shaving sensor may not react and the driving sound may not change. This is not abnormal.· To prevent erroneous operation, place your fingers on the finger rest while using the shaver.· The sonic vibration cleaning mode is activated when the power switch is pressed for more than 2 seconds while the shaver is not operating. (See page 18.) You cannot shave in this mode.Operation and display of the switch lock
Locking the power switch
1. Press once 2. Press for more 3. Release .
and then release. than 2 seconds
· The switch
· The shaver
until the switch
lock lamp
starts
lock lamp ( )
( ) will
operating.
turns on.
light up for
· The shaver will 5 seconds
stop operating. and turn off.
15
English
Unlocking the power switch
1. Press for more than 2 seconds until the switch lock lamp ( ) turns off.
2. Once the shaver starts operating, release . · The switch lock lamp ( ) will turn off.
Trimming sideburns
Preshave of long beards
· The power switch is locked when the switch lock lamp ( ) blinks for 5 seconds and the shaver does not operate even though the power switch is pressed.Using the trimmer1. Slide the trimmer handle up to the ” ” position so that the trimmer stands upright.2. Press and use.
Press and hold the top knob ()
and slide the trimmer handle
down to lower the trimmer.
Tips for better usage Apply the trimmer edge perpendicular to skin gently and move downward slowly.
16
Switching the shaver head You can change the pivot action.“” The shaver head is moved to prevent missed spots.“” You can lock the shaver head.
Cleaning, drying, charging
We recommend cleaning the shaver after each use.
1 Insert the shaver into theself-cleaning recharger 1
and plug the adaptor into
a household outlet (See
1
page 12)
2
· Check that the charge status
lamp ( ) is glowing.
· When the LOW lamp or the
STATUS lamp lights up, see
page 21.
2 Press
English
The CLEAN lamp and the DRY lamp glow, and the “AUTO” mode will start after approximately 6 seconds. · It is not possible to change the mode after the“AUTO” mode has started.
Clean 10 min
Dry 80 min*
Charge 0 to 60 min
Charge mode (Charge)
AUTO mode (Clean/Dry/Charge)
Dry/Charge mode(Dry/Charge)
*When the ambient temperature of the selfcleaning recharger is low (approx. 15 °C or lower), the drying process will take up to 170 min.3 Remove the adaptor after the selectedmode is completed
Clean the shaver with water once per month. (See pages 17 to 19.) The main unit neck section (), inner blade attachment part (), trimmer, system outer foil gaps, etc. cannot be cleaned with the selfcleaning recharger.
Changing the mode of self-cleaning rechargerThe “Charge” mode starts when attaching the shaver, and the mode can be changed by pressing the SELECT button.
Notes · Do not press the cleaning liquid unit removal buttonduring cleaning as the cleaning liquid may spill causing a malfunction. · The drying time may increase in an ambient temperature approximately 15 °C or lower. The Clean or Dry function may not operate under extreme low temperatures (approximately 0 °C or lower). · A lubricant constituent is included in the detergent, so smooth shave is maintained without applying oil.Cleaning thoroughlyCleaning with water· Turn the shaver off and disconnect the AC adaptor.1 Apply some hand soap andsome water to the system outer foil
17
English
2 Press for more than
2 seconds to activate the
sonic vibration cleaning
mode
· Splashing of foam is suppressed.
· The battery capacity lamps blink
in order.
· After about 20 seconds, it will be automatically
turned off, or you can turn it off by pressing the
power switch.
3 Remove the outer foil
section and clean with
running water
· See page 19 for removing the
outer foil section.
· Splashing is reduced by rinsing the shaver in sonic
vibration cleaning mode.
· After rinsing with water, shake the shaver up and
down for a few times to remove excess moisture and
then wipe off any drops of water with a dry cloth.
4 Attach the outer foilsection and dry with the 1
self-cleaning recharger
1. Insert the shaver into the
1
selfcleaning recharger and
2
plug the adaptor into a
household outlet.
· Check that the charge status
lamp ( ) is glowing.
2. Press twice.
18
The DRY lamp glows, and the “Dry/Charge” mode will start after approximately 6 seconds. · It is possible to change to the “AUTO” modeeven after the “Dry/Charge” mode has started.
Dry 180 min
Charge 0 to 60 min
3. Remove the adaptor after the selected mode is completed.5 Lubricate the shaver It will keep the movement of the blades smooth and maintain a comfort shave. 1. Apply one drop of oil to each of the system outer foils. 2. Raise the trimmer and apply a drop of oil. 3. Switch the shaver on, and run it for approximately five seconds. 4. Switch off the shaver, and wipe off any excess oil from the system outer foil with a soft cloth.Drying the shaver without the self-cleaning rechargerDry in a shade and apply oil.
English
Notes · Do not use any kitchen or bathroom detergents otherthan hand soap. Doing so may cause malfunction. · Be careful not to hit the main body on the sink or any other object while draining the water. Failure to do so may cause malfunction. · Do not wipe with thinners, benzine, alcohol etc. Doing so may cause malfunction, cracking or discoloration of the parts. Wipe with diluted soapy water. · Do not use the selfcleaning recharger while droplets or soap remain on the shaver. Doing so may change the concentration level or composition of the cleaning liquid in the cleaning liquid unit, which may degrade cleaning, sterilization, lubrication and drying performance. This may also cause cleaning liquid to spill from the selfcleaning recharger.Cleaning the system outer foilRemove the outer foil section. (See this page.) Wash the system outer foil in the areas indicated by the circles every time you use the shaver. Otherwise, abnormal sound may be generated.
Replacing the system outer foil and the inner blades
system outer foil inner blades
once every year once every two years
Removing the outer foil section Press the foil frame release buttons andlift the outer foil section upwards.
Attaching the outer foil section After turning the foil frame mark ( ) to the front, securely attach the outer foil section to the shaver until it clicks.Replacing the system outer foil 1. Press the system outer foil releasebuttons and pull down the system outer foil. · Do not press the system outer foilrelease buttons with excessive force. Doing so may bend the system outer foil, preventing complete attachment to the foil frame. 2. Align the foil frame mark ( ) and the system outer foil mark ( ) and securely attach together until it clicks.
19
English
Replacing the inner blades 1. Remove the inner blades one at a time. 2. Insert the inner blades one at a time.
Note Do not throw away the foil frame.
Replacing the cleaning liquid
If the STATUS lamp glows for 5 seconds when the
SELECT button is pressed, the cleaning liquid needs to
be replaced.
· Even if the STATUS lamp does not light up, replace
the cleaning liquid after 6 months have passed.
1 Remove the AC adaptor and
remove the cleaning liquid unit
(See page 13)
2 Wash away the old cleaning
1
liquid
· It can be drained as sewage.
3 Rinse the cleaning liquid unit · Pour water as illustrated while tilting the cleaning liquid unit and shaking it gently. · You can clean with the cleaning liquid filter removed. After washing, be sure to attach the cleaning liquid filter.20
4 Gently wipe off any beard
trimmings attached to the
inside of the cleaning tray () with a cloth or tissue
paper dampened with water
· Clean the corners and uneven
parts of the cleaning tray with a
cotton swab dampened with water.
5 Prepare the new cleaning liquid(See page 13)
The symbol on the left means “Do not wash the selfcleaning recharger with water”.
Notes · The cleaning liquid will decrease every time it is used,but do not add detergent and water except when replacing the cleaning liquid. Doing so may deteriorate the cleaning function. · Do not wash the selfcleaning recharger unit with water. · Do not wipe with thinners, benzine, alcohol etc. Doing so may cause malfunction, or cracking or discoloration of the parts. Wipe with diluted soapy water.When the water does not drain from the cleaning tray · Do not tilt the selfcleaning recharger to pour outwater. Doing so may cause the cleaning liquid in the cleaning liquid unit to spill or cause the selfcleaning recharger to malfunction.
English
· Beard trimmings may clog the drain at
the bottom of the cleaning tray.
In this case, you cannot clean or dry the
shaver.
1. Be sure to remove the AC adaptor
from the selfcleaning recharger.
2. Place the selfcleaning recharger on a
flat surface, and push the beard
trimmings down through the drain ()
with a toothpick etc.
Replacement parts Replacement parts are available at your dealer orService Centre.
System outer foil
Replacement parts and inner blades
for ESLV9U
System outer foil
WES9040 WES9181
Inner blades
WES9170
Special Detergent for Shaver Cleaning & Charging System
WES4L03
When the LOW/STATUS lamp glows
It indicates that the cleaning liquid is due for replacement when the LOW lamp or STATUS lamp glows for approximately 5 seconds when the SELECT button is pressed.
Lamp on the selfcleaning recharger The LOW lamp glows.The STATUS lamp glows.
Content of notificationReplacement of the cleaning liquid is required in approximately 7 days. Prepare the detergent.Replace the cleaning liquid. (Modes other than the “AUTO” mode can be used even if it is not replaced.)If you think the replacement should not be due yet. · Is the cleaning liquid unitcorrectly attached? · Is the selfcleaningrecharger placed in a level surface? · Is the selfcleaning recharger used outside the range of the recommended usage temperature? (Only “Charge” mode can be used.)
21
English
FAQ
QuestionWhy does “Dry/ Charge” mode take longer than “AUTO” mode?Can I refill the selfcleaning recharger with water when the cleaning liquid has decreased? Can the selfcleaning recharger be used to wash other models?Will the battery deteriorate if not used for an extended period of time?Can I charge the shaver after every use?22
AnswerThis is due to the difference in the drying time. The drying time for the “Dry/ Charge” mode is set longer as there may still be excess moisture on the areas other than the system outer foil after the shaver has been rinsed and cleaned with water.Do not refill with water as doing so may deteriorate the cleaning function. Replace the cleaning liquid.Doing so may cause malfunction, so do not use with other models.The battery will deteriorate if not used for over 6 months, so make sure to perform a full charge at least once every 6 months.The battery used is a lithiumion, so charging after every use will have no effect on battery life.
QuestionWhy should the adaptor be disconnected after charge?What is the constituent of the dedicated oil and the detergent?Why does the appliance beep twice after switched off?
AnswerCharging the battery for more than 1 hour will not affect battery performance, but disconnect the adaptor for safety and to save energy.Oil: Liquid paraffin Detergent: Nonionic surfactant agent, antimicrobial agent, lubricant and fragrance.The sound indicates that the battery capacity is running low. Please charge the appliance.
TroubleshootingPerform the following actions. If the problems still cannot be solved or all self cleaning recharger’s lamps blink, contact the store where you purchased the unit or a service centre authorized by Panasonic for repair.
English
Self-cleaning recharger
ProblemThe blade has not been thoroughly washed.The blades are not dry or are sticky.
ActionDo not add detergent and water except when replacing the cleaning liquid. Doing so may deteriorate the cleaning function. (See page 20.)After cleaning, oillike droplets may remain on the outside of the foil frame. This is the lubricating component of the cleaning liquid and does not indicate a problem. You may wipe it off with a soft cloth.The blades may not dry quickly due to temperature conditions. Run the “Dry/Charge” mode again or wipe with a soft cloth before shaving.
ProblemThe system outer foil cracks or deforms during cleaning.The cleaning liquid has foamed.
ActionDo not insert any foreign objects into the recharger. Remove foreign objects in the cleaning tray. (See page 20.)Replace the system outer foil and/or inner blades. (See page 19.)If you mix soapy water or hand soap with the detergent or use another detergent, the cleaning liquid will foam. Use the selfcleaning recharger after thoroughly washing and drying the shaver.Replace the cleaning liquid. (See page 20.)
23
English
ProblemCleaning liquid has accumulated in the cleaning tray.Cleaning liquid leaked from the cleaning liquid unit.The cleaning liquid unit cannot be removed.
ActionRemove any waste, etc. that has accumulated in the drain at the bottom of the cleaning tray. (See page 20.)If you use the selfcleaning recharger when the shaver is wet or when soap or shaving gel is on the shaver, cleaning liquid may accumulate in the cleaning tray.Do not press the cleaning liquid unit removal button during any mode.Place the selfcleaning recharger horizontally.If you use the selfcleaning recharger when the shaver is wet or when soap or shaving gel is on the shaver, cleaning liquid may leak.Place the selfcleaning recharger on a hard, flat surface. (See page 13.)
ProblemThe mode does not start.The shaver cannot be charged.
ActionCheck that the AC adaptor is connected to the self cleaning recharger, and that the adaptor is plugged in to a household outlet. (See page 16.)Confirm that the shaver is properly attached to the selfcleaning recharger. (See page 16.)The Clean or Dry function may not operate under extreme low temperatures (approximately 0 °C or lower).Check if the STATUS lamp is glowing. (See page 21.)Gently wipe the main body rear terminals and the charging terminals of the selfcleaning recharger with a cloth or tissue dampened with water.
24
English
ProblemMakes a loud sound.Shaver ProblemThe power switch does not turn ON.
ActionDuring cleaning: The selfcleaning recharger makes a loud sound due to the cleaning of the blades.After cleaning: The selfcleaning recharger makes a loud sound due to the removal of water droplets in order to speed drying.The sound after cleaning is different from the sound during cleaning. The water level has dropped and it is removing water droplets from the blades after cleaning. This does not indicate a problem.ActionUnlock the switch lock. (See page 16.)
ProblemThe shaving sensor does not respond.
ActionDepending on the beard thickness or the amount of beard trimmings in the shaver head, the shaving sensor may not react and the driving sound may not change. This is not abnormal.The shaving sensor may not respond depending on the type and quantity of the shaving gel. This is not abnormal.The shaving sensor may not respond when the remaining battery capacity is low. If this happens, recharge the shaver.Apply oil. (See page 18.) The shaving sensor may not respond when there is not enough oil on the blades.
25
English
ProblemThe shaving sensor responds even though the shaver is not in contact with the skin.Operating time is short even after a full charge.
ActionWhen the shaver is extremely dirty, remove the foil frame and wash with water. (See page 17.)Replace the system outer foil and/or inner blades. Expected life of system outer foil and inner blades: System outer foil:Approximately 1 year Inner blades:Approximately 2 yearsAlthough the shaver can be used for about 2 weeks after a full charge (assuming dryshave usages for 3 minutes per day), the usable number of days might be lower depending on how the shaver is used (for example, when used for wet shaving).Apply oil.Clean the shaver.When the number of operations per charge starts to decrease, the battery is nearing the end of its life.
26
ProblemShaver does not operate even after charging.The driving sound changes while shaving.Makes a loud sound.
ActionUse the appliance in an ambient temperature approximately 5 °C or higher.The battery has reached the end of its life.The shaver will not operate with the AC adaptor connected. Please use the shaver after it has been sufficiently charged and the AC adaptor disconnected.The shaving sensor is operating. The sound changes depending on the beard thickness.Apply oil. The blades will not move smoothly when there is no oil on the blades, requiring more power.The shaver makes a high pitched sound due to the linear motor drive. This does not indicate a problem.Confirm that the blades are properly attached.Wash the system outer foil with water. (See page 17.)
English
Problem The odor is getting stronger. Shavings fly out in all directions.System outer foil gets hot.You do not get as close a shave as before.
ActionClean the shaver.Clean the inner blades with water when shavings are adhering to the inner blades.Apply oil.Replace the system outer foil if it is damaged or deformed. (See page 19.)Clean the shaver.Apply oil.Replace the system outer foil and/or inner blades. Expected life of system outer foil and inner blades: System outer foil:Approximately 1 year Inner blades:Approximately 2 years
Removing the built-in rechargeable batteryRemove the built-in rechargeable battery before disposing of the shaver The battery is to be disposed of safely. Please make sure that the battery is disposed of at an officially designated location if there is one. This figure must only be used when disposing of the shaver, and must not be used to repair it. If you dismantle the shaver yourself, it will no longer be waterproof, which may cause it to malfunction. · Remove the shaver from the AC adaptor. · Press the power switch to turn on the power and thenkeep the power on until the battery is completely discharged.
Battery lifeThe life of the battery is 3 years. The battery in this shaver is not intended to be replaced by consumers. Have the battery replaced by an authorized service centre.27
English
· Perform steps to and lift the battery, and then remove it.· Take care not to short circuit the positive and negative terminals of the removed battery, and insulate the terminals by applying tape to them.
For environmental protection and recycling of materials This shaver contains a Lithiumion battery. Please make sure that the battery is disposed of at an officially assigned location, if there is one in your country.
Specifications
Power source
See the name plate on the AC adaptor. (Automatic voltage conversion)
Motor voltage 3.6 V
Charging time Approx. 1 hour
This product is intended for household use only.
Notes 1. Install on a hard, flat surface, except for handheldparts or fixed parts. 2. Store in a dry place indoors. 3. Transport without dropping, excessive vibration orhitting against other objects. 4. Dispose of according to national and/or locallegislation.Terms and conditions of sale are not set up by the manufacturer and must comply with national and/or local legislation of the country of sale of goods.
28
( )ESLV9U
30 35 37 38 40 44 46
47 / 48 49 50 54 55 56
Panasonic. , .29
.
, , . ,.
,.
,.
,
.
.
. , , , . , .. , . ( ..)., , . , .
.
, .
30
/. , . < > · , , . · , , . · , . .. .
. . , . . · , ,. , . .. – .
31
– , . – . (. . 37.) .. ., . .. – – .
, , , , . ., . . , .. – ., . , . .
32
, . , . .( ) , . , , . , . .. . .
, . . ( ) . .. , . – . .«» «/». – .. .
33
, . .. ., . ., . – ., . , .
· . . · , . · . · , , . · . · , , . · , , , . · . , .
34
, . . , ., , . . .
. .
· , . , . , .· , . , Panasonic / , , .· , . , .· . .· , . .
· . (. 38 « ».)35
· , . , .
·. , . · . .·. . · . .·. – . · . .
·. . · . , .
36
A
7
6 c
B
a b d
C
E
DF
A
d.
( )
·
.
6 B
7
(RC9-25)
a.
( )
b.
c.
( )
D
E
F
(
)
,
.
C
.
(RE7-87)
37
· .
·
.
1
2
.
2 ,
3
,
1
. ·
,
.
3 . · , ( ) . · 1 .4 .
, 3 , . ( ).
. .
, 5 .
· ,6 , ( ) . , . · , 10 °C 35 °C. , ( ) .
38
· 2 . ( 3- 20 °C 30 °C.) :· , .
· . · .
1
.
2
2
.
3
.
1
,
.
(. . 43.)
·
.
1
,
()
()
·
,
,
.
.
.
39
2
() ()
.
·
().
·
.
3.
· . . 47. ·Panasonic. , . · . .
· , 30 . ( ).
1 . · « », . , , , , .
40
, . ·, . · .2
5 . ·20 100. · ( ) .
5 .
«20». · 2-3 ,«20» . ( ).
·5 °C . ·. .
41
· , . .· .· 2 . (. . 44.) .
1.
2. 3.
,
.
. 2 ,
·
·
.
( )
( ). 5
·
.
.
1.
2.
2 ,
, .
·
( )
( ).
.
· , ( ) 5 .
1. « » , .2. .(), , .
.42
. «» . «» .
, ,
.
1
1
1
.
2
(. . 38.) · ,
( ) .
·
, . . 48.
2 , 6 «». · «».
10
80 *
0 60
* (. 15 °C ), 170 .43
3
·
.
.
(. . 44 46.)
15 °C . ( 0 °C ). · ,
(),
.
(), , . .
«», .
«» ()
«» (//)
«/ »(/)
·, .
· .1.22 , . · . · . · 20 . , .
44
3. · . . 46. · , . · , , .
4
1
. 1.
1 2
.
· ,
( ) .
2. .
,
6 «/
».
· «»
«/».
180
0 60
3. .5 . . 1. . 2. . 3. 5 . 4. .
.· –, . . · , – . .
45
· , , . . , . .· , . , , , . , .
. (. .) , , . .
.( ) , .1.. ·. , . 2. ( ) ( ) , , .1. . 2. .
.
46
5
,
.
· ,
6 .
1
. (. . 39.)
2
1
.
· .
3. · , , . · , . , .
4
() .
·
.
5 .(. . 39.)« ».·, , . . · . · , , . . , . . · , . .47
· ,
.
.
1.
.
2.
()
.
.
ES-LV9U
WES9040 WES9181
WES9170
WES4L03
/5 , .48
..
7 . .. ( , , «».), . ·? · ? · ? ( «».)
«/ » , «»?? ?
. «/» , , , ., . ., .. .
, ?????
, 6 , , 6 .– , .1 , .: : , , .. .49
. , , , Panasonic .
.
, . . (. . 47.). , , . .
50
…
– . «/» .. . (. . 47.)/ . (. . 46.), . .. (. . 47.)
..
. ., . (. . 47.), …, .
…
. (. . 39.), . (. . 43.), . (. . 43.)( 0 °C )., . (. . 48.), , .51
.
.
: .: , ., , , . , . .
. (. . 42.)
.
, . .. .. .. (. . 45.) , .
52
, .
, . (. . 44.)/ . : :1 :2
, .
, 2 ( 3 ), (, )…, .
53
…54
5 °C… , , .. .. , .– . ., .. (. . 44.)
. .., .
., .., . (. . 46.)../ . : :1 :2
3 . . .
. . , , . . , , . · . · ,, .
· , .· , .
– . , , .
55
.
. (
)
3,6
. 1
.
1., . 2. , . 3. , . 4. / ./ .
. 2 . 5 ” ” 7 , .1006, , 571-8501,
:(, ) . : X X XXXXX 1-, 2- …,J-, -, L- ( ) 0-2020, 1-2021 …, 9-2029
56
: (, , ) . : X XX XX -01, -02 …,-12 ( ) 0-2020, 1-2021…, 9-202957
58
( )ESLV9U
60 65 67 68 70 74 75
76 / 77 78 79 83 84 85
Panasonic. , .59
‘ .
, , . , , ,.,
.
,
.
, .
.
.
. , , , . , .. , . ( )., . , .
, .
60
‘ . , . < > · , , . · , , . · . .. .
. . , . . ·. . ., . .
61
, . , , . (. 67.) .. ., ‘ . ., . ., , , , , . .62
, . . , ., . ., . . .. , . .
( ) , , , , . , . . . , . .
. . ( ) . .
. . – . .“” “/”. .. .. .. .
63
, . .‘ . ., . .
· . . · , . · . · , , . · , ‘ . · , . · , , . · . , .
64
, . . , ., , , , . . .
, , , . .
· , . , . , , , .· , . , Panasonic / , , – .· . , .· . .· , . .
65
· . (. 68 « ».)· , . , ‘ .
·. , . · . .·. . · . ‘ .·. .
· ‘ . .·. . · . , .
66
A
7
6 c
B
a b d
C
E
DF
A
d.
( )
‘
‘
D
E
·
F
( )
.
6
7
,
a. B
( )
(RC9-25)
.
b.
C
.
c.
(RE7-87)
( )
67
· .
·
.
1
2 .
2 ,
3
,
1
. ·
,
.
3 . · , ( ) . · 1 .4 ‘.
68
, 3- . ( ).
. , , .
5 .
· ,6 , , ( ) . , . · 10 °C 35 °C. , , ( ) , .
· 2 . ( 3- 20 °C 30 °C.) .· , .
· . · ‘ .
1
.
2 .
2
3‘ .
1
,
.
(. 73.)
· ‘
.
1
,
()
() ·
‘ , ,
,
.
.
.
69
2
()
()
.
·
().
·
.
3.
· . . 76. ·Panasonic. . · . . · , 30 . ( .)70
1 . · ” “, . , , , , ., , . ·, . · , .2
5 . ·20 100. · ( ) .
5 .
“20”. · 2-3 , “20”( ).
·5 °C . ·. .
· , . .· , .· , 2 , . (. 74.) .
1.
2.
.
2 ,
·
.
3. .· ( )
( ).
5
·
.
.
71
1. 2. 2 , ,. ( ). ·( ) .
· , , ( ).
1. ” “, .2. .
.“” , .“” .
(), , ..72
, ,
.
1
1
1
. (. 68.)
2
· ,
( ) .
·
,
. . 77.
2 , 6 “”. · “”.
10
80 *
0 60
* , (. 15 °C ), 170 .3 ‘.
. (. 74 – 75.) (), (), , .
“”, .
“” ()
“” (/ /)
“/ ” (/ )
·, , . · 15 °C . ( 0 °C ). · , .73
· ‘ .1.22 , . · . · . · 20 , .3. · . . 75.
· , .· , , , , .
41
. 1.
1 2
.
· ,
( ) .
2. .
, 6
“/”.
· “”
“/”.
180
0 60
3. ‘ .
74
5 . . 1. . 2. . 3. 5 . 4. , ‘ .
.
· , . , , , . .
. (. ) , , . .
· –
, .
. · ,. . · , , .
.
,
.
. 75
( ) , .1.. ·. , . 2. ( ) ( ) ‘ , , .1. . 2. ..
5 , , . 76
· , 6 .
1 ‘. (. 69.)
2 .
1
· .
3. · , , . · . , .
4 ,
(),
, .
·
,
.
5 .(. 69.)
« ».· ‘, , . . · . · , , . , . .· ,. .
·
.
.
1. ‘ ‘
.
2.
()
.
.
ESLV9U
WES9040
WES9181
WES9170
WES4L03
/, 5 .
77
..78
7 . .. ( , , “”.), . ·? · ? · ? ( “”.)
“/ ” , “”???, ?
‘ . “/ ” , , , ., . ., ., 6 , 6 .
?‘ ???
– , .1 , , ‘ .: : – , , .. .
. , , , Panasonic .
.
. . (. 77.). , , . ‘ .
79
…
. “/ ” , ‘ .. . (. 76.)/ . (. 75.), . .. (. 76.)
..
, . (. 77.), , .– .., , .
80
…
. (. 69.), . (. 73.), . (. 73.)( 0 °C )., . (. 77.), .
.
.
:, . : . , , , . , . .. (. 72.)81
.
, . .. .. .. (. 75.) , .
82
, ., .
, . (. 74.)/ . : :1 :22 ( 3- ), , , (, )…, , .
…
5 °C .., ‘ . , ‘ .. .. , .. ., .. (. 74.)
. .., .
., .., . (. 75.)../ . : :1 :2
3 . . .
83
. . , , . , . , . · . ·, .
· , , .· , .
– . , , .
84
.
.
( )
3,6
. 1
.
1. , . 2. . 3. ,‘. 4./ ./ .
() 7 , , , .Panasonic Corporation 1006, Kadoma, Osaka 5718501, Japan 1006, , 571-8501,Panasonic : +38-0-(44)-490-38-98 :0800309880:(, ) , . : X X XXXXX
— 1 — , 2 — … , J — , K — , L —( ) -0 — 2020 , 1 — 2021 … , 9 — 202985
:(, , ) , . : X XX XX
-01, -02 …, -12( ) 0-2020, 1-2021…, 9-2029
‘ , .
, , https://service. panasonic.ua « »: ” ” . , 30, . 03022,. , . / .
86
( )ESLV9U
88 93 95 96 98 102 103
104 / 106 107 108 113 113 114
Panasonic . .87
.
, ..
.
.
. .
.
. , , . , , .. , , . ( , ..) .. , , .
.
88
, , . , , . < > · , – , . · , – , . · , – . , .. , .
– . – . . . · , ,. -, , . , .. , .
89
– . – – . (95 .) , . . . . , . . , .. .90
. . .– . , ., , . , . ., . , . .
, – , ( ) . . . , . . , .
, . . ( ) . .
. , . , . , .“” “/” – . .. .. , .. .
91
. . . . . .92
· . . · . · . · , , . · . · . · . · . , , .
. , . , .
, , . . , . .
, , . , .
· . . .· , . Panasonic / , .
· . .· , . .· . .· . (96- ” ” .)· . .
· ., . · . , .·. .93
· . .·. , . · . . · . . · . , , .94
A
7
a
6
b
c
d
B
C
E
DF
A
d.
( )
·
.
6
7
a. B –
( )
b.
(RC9-25)
c.
( )
C
(RE7-87)
–
D
E
F
( )
– , . .
95
· .
·
.
1 –
2
.
2
3
,
1
–
.
·
,
–
.
3 e . · ( ) . · 1 .4.
, 3 . ( .)
. .
, 5 .
·6 , ( ) . , . · 10 °C 35 °C . ( ) .
96
· 2 . (20 °C 30 °C 3 .) .· , .
–
· .
· .
1
.
2 e
2
.
3
.
1
,
.
(101 .)
· –
.
1 ,
,
(),
()
· –
,
.
.
.
97
2
()
()
.
·
()
.
·
.
3– .
· 104- . · Panasonic– . . · – . . · , 30 . ( .)98
1 ,. · ” ” . ., , , . ·. · .2 .
, 5 . ·20-100 . · ( ) .
, 5 .
“20” . · “20” 2 3. ( .)
· 5 °C. ·. .
· . .· .· 2 . (102 .) .
1. 2. 3.
, ( )
.
.
·
· 2
.
.
()
·
5
.
,
.
99
1.
2.
( )
.
2
·
. ( ) .
· , , ( ) 5 , .
1. ” ” .2. , .
.“” .“” .
() ., .
100
, ,
.
1 –
1
,
.
1
(96 .)
2
·
( )
.
·
,
106- .
2 . , 6 “” . · “” , .
10
80 *
0-60
* – (. 15 ° ), 170 . .3.
. (102 – 103 .) (), (), , , .. – .
–
«» , .
()
“” (//)
/(/ )
·, , . · 15 °C , . ( 0 °C ) “” “” .101
· , .
· .1.22 . · . · . · 20 , .3 ,. · 103- .102
· .· , .
4
1
–
.
1 2
1. –
,
.
· ( )
.
2. .
“/”
6 .
· «/»
“” .
180
0-60
3. .
5 . . 1. . 2. , . 3. , . 4. , .–, .
· , – . , , , . -, – .
. ( .) . , .
·. . · . . · , , , .. . , . .
.
103
( ) , , , .1.. ·. , . 2. ( ) ( ) , , .1. – . 2. .
5 , . · , , 6.
1
.
1
(97 .)
2 . · .
3. · , . · . .
.
104
4
()
.
·
.
5 .(97 .)
«- » .
· ,, . . · – . · , , , .. . , . .
· –
.
–
.
·
.
. 1. –
.
2. –
,
()
, .. .
.
ES-LV9U
WES9040
WES9181
WES9170
WES4L03
105
/
5 .
–
.
7 . .
–.
. (“” , .). ·? · –? · – ? ( “” .)
106
“/ ” “” ?– ? – ?, ?
. “/” , , ., . ., – .6 , , 6 .
????
– , , .1 , .: : – , , .. .
107
. – , Panasonic .
–
.
, . . (105 .). — . .
108
…
. “/ ” .. . (105 .)/ . (103 .), . – .. (104 .)
.
, .. . (105 .)– , .
..
.– .– , .– , . (97 .)
109
.. 110
– . (101 .)– . (101 .)( 0 °C ) “” “” .. (106 .)– .
.
.
: – .: – .. . .
. (100 .)
.
. .. ., . , .. (103 .) , .
.
, . (102 .)/ . : :1 :2
111
.
2 ( 3 ), (, ) …, .
112
…
5 °C … .. .. , , .. … (102 .)
. …
., .., . (103 .)../ . : :1 :2
. . ( ) . . , , . · . · ,, .
— 3 . . .113
· , , .· .
– . .
. ( )
3,6
1
.
1. , ,. 2. . 3. ,. 4..C .
114
, 7 ( )1006, , 571-8501,
:(, ) . : X X XXXXX— 1 — , 2 — … ,J — , K — , L — () -0 — 2020 , 1 — 2021 … , 9 — 2029
:(, , ) . : X XX XX
– 01, 02 … -12( ) -0 — 2020 , 1 — 2021 … , 9 — 2029
115
F EN, RU, UA, KZ
Panasonic Corporation http://www.panasonic.com© Panasonic Corporation 2022
report this adPrinted in Japan ES9700LV9U1G Y02220
References
[xyz-ips snippet=”download-snippet”]