Asus XG25BQ Republic of Gamers ROG Strix Gaming Monitor User Manual
Notices
Federal Communications Commission StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Canadian Department of Communications StatementThis digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.This class B digital apparatus complies with Canadian ICES-003.This Class B digital apparatus meets all requirements of the Canadian Interference– Causing Equipment Regulations.
Safety information
- Before setting up the monitor, carefully read all the documentation that camewith the package.
- To prevent fire or shock hazard, never expose the monitor to rain or moisture.
- Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury.
- If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
- Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
- Slots and openings on the back or top of the cabinet are provided for ventilation. Do not block these slots. Never place this product near or over a radiator or heat source unless proper ventilation is provided.
- The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.
- Use the appropriate power plug which complies with your local power standard.
- Do not overload power strips and extention cords. Overloading can result in fire or electric shock.
- Avoid dust, humidity, and temperature extremes. Do not place the monitor in any area where it may become wet. Place the monitor on a stable surface.
- Unplug the unit during a lightning storm or if it will not be used for a long period of time. This will protect the monitor from damage due to power surges.
- Never push objects or spill liquid of any kind into the slots on the monitor cabinet.
- To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC.
- If you encounter technical problems with the monitor, contact a qualified service technician or your retailer.
- Adjustment of the volume control as well as the equalizer to other settings than the center position may increase the ear-/headphones output voltage and therefore the sound pressure level.
- The adapter is only used for this monitor, do not use it for other purpose. Your device uses one of the following power supplies:
- Manufacturer: Delta Electronics Inc., Model: ADP-65GD B
This symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment, and mercury-containing button cell battery) should not be placed in municipal waste. Please check local regulations for disposal of electronic products.
Care & Cleaning
- Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques when positioning the monitor. When lifting or carrying the monitor, grasp the edges of the monitor. Do not lift the display by the stand or the cord.
- Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed with a cloth dampened with mild cleaner.
- Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended for use with the monitor. Never spray cleaner directly on the screen, as it may drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
- The screen may flicker during the initial use due to the nature of the fluorescent light. Turn off the Power Switch and turn it on again to make sure that the flicker disappears.
- You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
- When the same image is displayed for hours, an afterimage of the previous screen may remain after switching the image. The screen will recover slowly or you can turn off the Power Switch for hours.
- When the screen becomes black or flashes, or cannot work anymore, contact your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions used in this guide WARNING: Information to prevent injury to yourself when trying to complete a task.
CAUTION: Information to prevent damage to the components when trying to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
Where to find more informationRefer to the following sources for additional information and for product and software updates.
- ASUS websitesThe ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to http://www.asus.com
- Optional documentationYour product package may include optional documentation that may have been added by your dealer. These documents are not part of the standard package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials.Please go to http://csr.asus.com/english/Takeback.htm for detail recycling information in different region.
Welcome!
Thank you for purchasing the ROG gaming monitor!The latest widescreen LCD monitor from ASUS provides a broader, brighter and crystal-clear display, plus a host of features that enhance your viewing experience. With these features, you can enjoy the convenience and delightful visual experience that the monitor brings to you!
Package contents
Check your package for the following items:
- LCD monitor
- Monitor base
- Driver and Manual disc
- Quick start guide
- Warranty card
- Power adapter
- Power cord
- DP cable
- HDMI cable
- LED projection cover and changeable films
- Input/Output port cover
If any of the above items is damaged or missing, contact your retailer immediately.
Select “ON” when you see the message “AURA & LIGHT IN MOTION” appears if you want to turn on the light on the base and the back. If you disable this function but later wish to reactivate it, please use the OSD menu to turn it on.
Monitor introduction
Front/side view
1. 
( 
5-way) button:
- Turns on the OSD menu. Enacts the selected OSD menu item.
- Increases/Decreases values or moves your selection up/down/left/right.
- Turns on the OSD menu when the monitor enters standby mode or displays the “NO SIGNAL“ message.
2.
button
- Exits the OSD menu item.
- Turns on the OSD menu when the monitor enters standby mode or displays the “NO SIGNAL“ message.
3. 
button:
- GamePlus hotkey. Move the
( ) button up/down to select and press ( ) to confirm the function needed. - Turns on the OSD menu when the monitor enters standby mode or displays the “NO SIGNAL“ message.
4. 
button
- GameVisual hotkey. This function contains 8 sub-functions you can select for your preference.
- Turns on the OSD menu when the monitor enters standby mode or displays the “NO SIGNAL“ message.
5. 
Power button/power indicator
- Turns the monitor on/off.
- The color definition of the power indicator is as the below table
| Status | Description |
| White | ON |
| Amber | Standby mode/No signal |
| OFF | OFF |
Back view
- Kensington lock slot.
- HDMI-1 port. This port is for connection with an HDMI 1.4 compatible device.
- HDMI-2 port. This port is for connection with an HDMI 2.0 compatible device.
- DisplayPort. This port is for connection with a DisplayPort compatible device.
- DC-IN port. This port connects the power cord.
- Earphone jack. This port is only available when an HDMI/DisplayPort cable is connected.
- Control buttons.
GamePlus Function
The GamePlus function provides a toolkit and creates a better gaming environment for users when playing different types of games. The crosshair overlay with four different crosshair options lets you choose the one that best suits the game you’re playing. There’s also an onscreen timer you can position on the left of the display so you can keep track of the elapsed gaming time; while the FPS (frames per second) counter lets you know how smooth the game is running. Display Alignmentdisplays alignment lines on 4 sides of the screen, serving as an easy and handy tool for you to line up multiple monitors perfectly.To activate GamePlus:
- Press the GamePlus hotkey.
- Move the () button up/down to select among different functions.
- Press the () button or move the () button right to confirm the function you choose, and move the () button up/down to navigate through the settings. Move the () button left to go back, off, and exit.
- Highlight the desired setting and press the () button to activate it. Press the button to inactivate it.
|
GamePlus Main Menu |
GamePlus Crosshair |
GamePlus Timer |
GamePlus FPS counter |
 |
 |
 |
 |
GameVisual Function
The GameVisual function helps you select among different picture modes in a convenient way.To activate GameVisual:
- Press the GameVisual hotkey
- Move the () button up/down to highlight a desired setting.
- Press the () button or move the button right to activate it.
- To exit the menu, move the () button left .
- Scenery Mode: This is the best choice for scenery photo displaying with GameVisualTM Video intelligence Technology.
- Racing Mode: This is the best choice for racing game playing with GameVisualTM Video intelligence Technology.
- Cinema Mode: This is the best choice for movie watching with GameVisualTM Video intelligence Technology.
- RTS/RPG Mode: This is the best choice for Real-Time Strategy (RTS)/Role-Playing Game (RPG) playing with GameVisualTM Video intelligence Technology.
- FPS Mode: This is the best choice for First Person Shooter game playing with GameVisualTM Video intelligence Technology.
- sRGB Mode: This is the best choice for viewing photos and graphics from PCs.
- MOBA Mode: This is the best choice for multiplayer online battle arena game playing with GameVisual™ Video intelligence Technology.
- User Mode: More items are adjustable in the Color menu.
In the Racing/MOBA mode, the following function(s) are not userconfigurable: ASCR, Saturation. In the sRGB mode, the following function(s) are not user-configurable:Color Temp., Brightness, Contrast, ASCR, Saturation.
Assembling the monitor arm/base
- Insert the base into the arm.
- Fix the base to the arm by fastening the bundled screw.
- Attach the LED projection cover to the stand.
We recommend that you cover the table surface with soft cloth to prevent damage to the monitor.
To change the film on the LED projection cover, follow the illustration below.
Cable management
You can organize the cables with the help of the input/output port cover.
- Arranging the cables
- Using the input/output port cover:The cover can be attached or detached.
Adjusting the monitor
- For optimal viewing, we recommend that you look at the full face of the monitor, then adjust the monitor to the angle that is most comfortable for you.
- Hold the stand to prevent the monitor from falling when you change its angle.
- The recommended adjusting angle is +20˚ to -5˚ (for tilt)/+50˚ to -50˚ (for swiveling/+120 mm (for height adjustment)/90˚ (for portrait view).
It is normal that the monitor slightly shakes while you adjust the viewing angle.
Pivoting the monitor
- Lift the monitor to the highest position.
- Tilt the monitor to its maximum angle.
- Pivot the monitor clockwise to the angle you need.
It is normal that the monitor slightly shakes while you adjust the viewing angle.
Detaching the arm (for VESA wall mount)
The detachable arm of this monitor is specially designed for VESA wall mount.To detach the arm:
- Have the front of the monitor face down on a table.
- Remove the covers on where the monitor and the arm meet.
- Loosen the four screws on the back of the monitor and remove the arm/base.
We recommend that you cover the table surface with soft cloth to prevent damage to the monitor.
- The VESA wall mount kit (100 x 100 mm) is purchased separately.
- Use only the UL Listed Wall Mount Bracket with minimum weight/load 22.7kg (Screw size: M4 x 10 mm)
Connecting the cables
Connect the cables as the following instructions:
- To connect the power cord:a. Connect the power adapter securely to the monitor’s DC input.b. Connect one end of the power cord to the power adapter and the other end to a power outlet.
- To connect the DisplayPort/HDMI cable:a. Plug one end of the DisplayPort/HDMI cable to the monitor’s DisplayPort/HDMI port.b. Connect the other end of the DisplayPort/HDMI cable to your computer’s DisplayPort/HDMI port.
- To use the earphone: connect the end with plug type to the monitor’s earphone jack when an HDMI or DisplayPort signal is fed.
Turning on the monitor
Press the power button . See page 1-2 for the location of the power button. The power indicator lights up in white to show that the monitor is ON.
How to reconfigure
- Press the () button to activate the OSD menu.
- Move the () button up/down to navigate through the functions. Highlight the desired function and press the () button to activate it. If the function selected has a sub-menu, move the () button up/down again to navigate through the sub-menu functions. Highlight the desired submenu function and press the () button or move the () button right to activate it.
- Move the () button up/down to change the settings of the selected function.
- To exit and save the OSD menu, press the button or move the () left repeatedly until the OSD menu disappears. To adjust other functions, repeat steps 1-3.
OSD function introduction
GameVisualSee 1.3.4 GameVisual Function for details
Blue Light FilterIn this function, you can adjust the blue light filter level.
- Level 0: No change.
- Level 1~4: The higher the level, the less blue light is scattered. When Blue Light Filter is activated, the default settings of Racing Mode will be automatically imported. Between Level 1 to Level 3, the Brightness function is user-configurable. Level 4 is an optimized setting. It is in compliance with TUV Low Blue Light Certification. The Brightness function is not user-configurable.
- Please refer to the following to alleviate eye strains:
- Users should take some time away from the display if working for long hours. It is advised to take short breaks (at least 5 mins) after around 1 hour of continuous working at the computer. Taking short and frequent breaks is more effective than a single longer break.
- To minimize eye strain and dryness in your eyes, you should rest the eye periodically by focusing on objects that are far away.
- Eye exercises can help to reduces eye strain. Repeat these exercises often. If eye strain continues please consult a physician. Eye exercises: (1) Repeating look up and down (2) Slowly roll your eyes (3) Move your eyes diagonal.
- High energy blue light may lead to eye strain and AMD (Age-Related Macular Degeneration). Blue light Filter reduces 70% (max.) harmful blue light to avoid CVS (Computer Vision Syndrome).
Color
You can adjust Brightness, Contrast, Saturation, Color Temperature, and Gamma from this menu.
- Brightness: The adjusting range is from 0 to 100.
- Contrast: The adjusting range is from 0 to 100.
- Saturation: The adjusting range is from 0 to 100.
- Color Temp.: Contains 4 modes including Cool, Normal, Warm, and User Mode.
- Gamma: Allows you to set the color mode to 2.5, 2.2, or 1.8.
ImageYou can adjust OD, Aspect Control, ASCR, ELMB, and Adaptive-Sync/FreeSync from this menu.
- OD: Improves the gray level response time of the LCD panel.
- Aspect Control: Adjusts the aspect ratio to Full or 4:3.
- ASCR: Turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
- ELMB: Turns on/off the ELMB (Extreme Low Motion Blur) function. This function is available when the refresh rate is 100Hz, 120Hz, or 144Hz.
- Adaptive-Sync/FreeSync: Allows an Adaptive-Sync/Freesync supported* graphics source to dynamically adjust display refresh rate based on typical content frame rates for power efficient, virtually stutter free and low-latency display update.
To activate Adaptive-Sync/FreeSync, turn off ELMB function first.
- Adaptive-Sync/FreeSync can only be activated within 48Hz~120Hz forHDMI1.4, and 48Hz~240Hz for HDMI2.0 and DisplayPort.
- For supported GPUs, minimum PC system and driver requirements, please contact the GPU manufactures.
SoundSet the sound related setting from this menu.
- Volume: The adjusting range is from 0 to 100.
- Mute: Toggles the monitor sound between on and off.
Input SelectIn this function, you can select your desired input source.
System SetupAllows you to adjust the system.
- LIGHT IN MOTION: Selects the brightness level of the light on the stand. The adjusting range is from Level 0 to 3, Level 0 = Off.
- Aura RGB: There are 6 living colors can be chosen: Rainbow, Color Cycle, Static, Breathing, Strobing, OFF. You can manually change the R/G/B/C/M/Y color for Static, Breathing, and Strobing modes.
- OSD Setup:
- Adjusts the OSD timeout from 10 to 120 seconds.
- Enables or disables the DDC/CI function.
- Adjusts the OSD background from opaque to transparent.
- Language: There are 21 languages for your selection, including English, French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech, Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chinese, Traditional Chinese, Japanese, Korean, Thai, Indonesia, Persian.
- Information: Shows the monitor information.
- Key Lock: To disable all function keys. Press over 5 seconds to cancel the key lock function.
- Power Indicator: Turns the power LED indicator on/off.
- Power Key Lock: Enables or disables the power key.
- All Reset: Selecting “Yes” allows you to restore the default settings.
MyFavoriteLoads/Saves all settings on the monitor.
Specifications summary
| Panel type | TFT LCD |
| Panel size | 24.5”W (16:9, 62.2 cm) wide screen |
| Max. resolution | 1920 x 1080 |
| Pixel pitch | 0.2832 mm x 0.2802 mm |
| Brightness (Typ.) | 400 cd/m2 |
| Contrast ratio (Typ.) | 1000:1 |
| Viewing angle(H/V) CR>10 | 170˚/160˚ |
| Display colors | 16.7 M |
| Response time | 1 ms (Gray to Gray) |
| Color temperature selection | 4 color temperatures |
| Analog input | No |
| Digital input | DisplayPort v1.2 x 1,
HDMI v1.4 x 1/v2.0 x 1 |
| Earphone jack | Yes |
| Audio input | No |
| Speaker (Built-in) | No |
| Colors | Black |
| Power LED | White (On)/Amber (Standby) |
| Tilt | +20˚~ -5˚ |
| Pivot | 90˚ (clockwise) |
| Swivel | +50˚~ -50˚ |
| Height adjustment | 120 mm |
| VESA wall mount | 100 x 100 mm |
| Kensington lock | Yes |
| Voltage rating | AC: 100~240V
DC: 19V, 3.42A (AC adapter) |
| Power consumption | Power On: < 65 W,
Standby: < 0.5 W, Power Off: < 0.5 W |
| Temperature (Operating) | 0˚C~40˚C |
| Temperature (Non-operating) | -20˚C~+60˚C |
| Dimensions (W x H x D) | 564.2 x 383.7 x 253.7 mm (lowest)
564.2 x 503.7 x 253.7 mm (highest) 661 x 443 x 239 mm (package) |
| Weight (Esti.) | 5.5 kg (Net); 8.2 kg (Gross) |
| Multi-languages | 21 languages (English, French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech, Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chinese, Traditional Chinese, Japanese, Korean, Thai, Indonesia, Persian) |
| Accessories | DP cable, HDMI cable, Power adapter, Power cord, Driver and Manual disc, Quick start guide, Warranty card, LED projection cover and changeable films, Input/Output port cover |
| Compliance and standards | CB, CE, CU, CCC, UL/cUL, FCC, RCM, BSMI, VCCI, RoHS, WEEE, J-MOSS, ErP, PSE, CEL, Windows 7 WHQL, Windows 8.1 WHQL, Windows 10 WHQL, KCC, E-Standby, TUVFlicker Free, TUV-Low Blue Light, UkrSEPRO, MEPS |
*Specifications are subject to change without notice.
Troubleshooting (FAQ)
| Problem | Possible Solution |
| Power LED is not ON |
|
| The power LED lights white and there is no screen image |
|
| Screen image is too light or dark |
|
| Screen image bounces or a wave pattern is present in the image |
|
| Screen image has color defects (white does not look white) |
|
Supported operating mode
| Resolution frequency | Refresh rate | Horizontal |
| 640×350 | 70Hz | 31.469KHz |
| 640×350 | 85Hz | 37.861KHz |
| 640×480 | 60Hz | 31.469KHz |
| 640×480 | 67Hz | 35KHz |
| 640×480 | 75Hz | 37.5KHz |
| 640×480 | 85Hz | 43.269KHz |
| 720×400 | 70Hz | 31.469KHz |
| 720×400 | 85Hz | 37.927KHz |
| 800×600 | 56Hz | 35.156KHz |
| 800×600 | 60Hz | 37.897KHz |
| 800×600 | 72Hz | 48.077KHz |
| 800×600 | 75Hz | 46.875KHz |
| 800×600 | 85Hz | 53.674KHz |
| 832×624 | 75Hz | 49.725KHz |
| 848×480 | 60Hz | 31.02KHz |
| 1024×768 | 60Hz | 48.363KHz |
| 1024×768 | 70Hz | 56.476KHz |
| 1024×768 | 75Hz | 60.023KHz |
| 1024×768 | 85Hz | 68.677KHz |
| 1152×864 | 75Hz | 67.5KHz |
| 1280×720 | 60Hz | 44.444KHz |
| 1280×720 | 60Hz | 44.772KHz |
| 1280×720 | 75Hz | 56.456KHz |
| 1280×768 | 60Hz | 47.396KHz |
| 1280×800 | 60Hz | 49.306KHz |
| 1280×800 | 60Hz | 49.702KHz |
| 1280×800 | 75Hz | 62.795KHz |
| 1280×960 | 60Hz | 60KHz |
| 1280×1024 | 60Hz | 63.981KHz |
| 1280×1024 | 75Hz | 79.976KHz |
| 1366×768 | 60Hz | 47.712KHz |
| 1440×900 | 60Hz | 55.469KHz |
| 1440×900 | 60Hz | 55.935KHz |
| 1440×900 | 75Hz | 70.635KHz |
| 1680×1050 | 60Hz | 64.674KHz |
| 1680×1050 | 60Hz | 65.29KHz |
| 1920×1080 | 60Hz | 66.587KHz |
| 1920×1080 | 60Hz | 67.5KHz |
| 1920×1080 | 85Hz | 95.43KHz |
| 1920×1080* | 100Hz | 113.3KHz |
| 1920×1080* | 120Hz | 137.2KHz |
| 1920×1080* (DP) | 144Hz | 158.11KHz |
| 1920×1080 (DP/HDMI-2) | 240Hz | 291.309KHz |
| 640x480P (HDMI) | 59.94/60Hz | 31.469KHz/31.5KHz |
| 720x480P (HDMI) | 59.94/60Hz | 31.469KHz/31.5KHz |
| 720x576P (HDMI) | 50Hz | 31.25KHz |
| 1280x720P (HDMI) | 50Hz | 37.5KHz |
| 1280x720P (HDMI) | 59.94/60Hz | 44.955KHz/45KHz |
| 1440x480P (HDMI) | 59.94/60Hz | 1.469KHz/31.5KHz |
| 1440x576P (HDMI) | 50Hz | 31.25KHz |
| 1920x1080P (HDMI) | 50Hz | 56.25KHz |
| 1920x1080P (HDMI) | 59.94/60Hz | 7.433KHz/67.5KHz |
Note:
- Only DP supports Extreme Low Motion Blur.
Asus XG25BQ Republic of Gamers ROG Strix Gaming Monitor User Manual – Asus XG25BQ Republic of Gamers ROG Strix Gaming Monitor User Manual –
[xyz-ips snippet=”download-snippet”]