IKEA TVATTAD User Manual
Safety information
Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
Children and vulnerable people safety
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
- Children between 3 and 8 years of age and persons with very extensive and complex disabilities shall be kept away from the appliance unless continuously supervised.
- Children of less than 3 years of age should be kept away from the appliance unless continuously supervised.
- Do not let children play with the appliance.
- Keep all packaging away from children and dispose of it appropriately.
- Keep detergents away from children.
- Keep children and pets away from the appliance when the door is open.
- If the appliance has a child safety device, it should be activated.
- Children shall not carry out cleaning and user maintenance of the appliance without supervision.
General Safety
- Do not change the specification of this appliance.
- This appliance is intended to be used in household and similar applications such as:– staff kitchen areas in shops, offices, and another working environment;– by clients in hotels, motels, bed & breakfast, and other residential type environments;– areas for communal use in blocks of flats or in launderettes.
- Do not exceed the maximum load of 8 kg (refer to the “Programme chart” chapter).
- The operating water pressure at the water entry point from the outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa).
- The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering.
- The appliance must be connected to the water mains using the new supplied hose-sets, or other new hose-sets supplied by the Authorised Service Centre.
- Old hose sets must not be reused.
- If the mains power supply cable is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard.
- Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket.
- Do not use high-pressure water sprays and/or steam to clean the appliance.
- Clean the appliance with a moist cloth. Use only neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects.
Safety instructions
Installation
The installation must comply with relevant national regulations.
- Remove all the packaging and the transit bolts including rubber bush with plastic spacer.
- Keep the transit bolts in a safe place. If the appliance is to be moved in the future it must be reattached to lock the drum to prevent internal damage.
- Always take care when moving the appliance as it is heavy. Always use safety gloves and enclosed footwear.
- Follow the installation instructions supplied with the appliance.
- Do not use the appliance before installing it in the built-in structure due to safe manner.
- Do not install or use a damaged appliance.
- Do not install or use the appliance where the temperature can be less than 0°C or where it is exposed to the weather.
- The floor area on which the appliance is to be installed must be flat, stable, heat resistant, and clean.
- Make sure that there is air circulation between the appliance and the floor.
- When the appliance is in its permanent position, check if it is leveled correctly with the aid of a spirit level. If it is not, adjust the feet accordingly.
- Do not install the appliance directly above a floor drain.
- Do not spray water on the appliance and do not expose it to excessive humidity.
- Do not install the appliance where the appliance door cannot be fully opened.
- Do not put a closed container to collect possible water leakage under the appliance. Contact the Authorised Service Centre to ensure which accessories can be used.
Electrical connection
Warning! Risk of fire and electric shock.
- The appliance must be earthed.
- Always use a correctly installed shockproof socket.
- Make sure that the parameters on the rating plate are compatible with the electrical ratings of the mains power supply.
- Do not use multi-plug adapters and extension cables.
- Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre.
- Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
- Do not touch the mains cable or the mains plug with wet hands.
- Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
Water connection
- Do not cause damage to the water hoses.
- Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear.
- Ensure that there are no visible water leaks during and after the first use of the appliance.
- Do not use an extension hose if the inlet hose is too short. Contact the Authorised Service Centre for the replacement of the inlet hose.
- When unpacking the appliance, It is possible to see water flowing from the drain hose. This is due to the testing of the appliance with the use of water in the factory.
- You can extend the drain hose to a maximum of 400 cm. Contact the Authorised Service Centre for the other drain hose and the extension.
- Make sure that there is access to the tap after the installation.
Use
Warning! Risk of injury, electric shock, fire, burns, or damage to the appliance.
- Follow the safety instructions on the detergent packaging.
- Do not put flammable products or items that are wet with flammable products in, near, or on the appliance.
- Do not wash fabrics that are heavily soiled with oil, grease, or other greasy substances. It can damage the rubber parts of the washing machine. Prewash such fabrics by hand before loading them into the washing machine.
- Do not touch the glass door while a program operates. The glass can get hot.
- Make sure that all metal objects are removed from the laundry.
Internal lighting
Warning! Risk of injury.
- Concerning the lamp(s) inside this product and spare part lamps sold separately: These lamps are intended to withstand extreme physical conditions in household appliances, such as temperature, vibration, humidity, or are intended to signal information about the operational status of the appliance. They are not intended to be used in other applications and are not suitable for household room illumination.
- To replace the internal lighting, contact the Authorised Service Centre.
Service
- To repair the appliance contact the Authorised Service Centre. Use original spare parts only.
- Please note that self-repair or nonprofessional repair can have safety consequences and might void the guarantee.
- The following spare parts will be available for 10 years after the model has been discontinued: motor and motor brushes, transmission between motor and drum, pumps, shock absorbers, and springs, washing drum, drum spider and related ball bearings, heaters and heating elements, including heat pumps, piping and related equipment including hoses, valves, filters and aqua stops, printed circuit boards, electronic displays, pressure switches, thermostats and sensors, software and firmware including reset software, door, door hinge and seals, other seals, door locking assembly, plastic peripherals such as detergent dispensers. Please note that some of these spare parts are only available to professional repairers and that not all spare parts are relevant for all models.
Disposal
Warning! Risk of injury or suffocation.
- Disconnect the appliance from the mains electricity and water supplies.
- Cut off the mains electrical cable close to the appliance and dispose of it.
- Remove the door catch to prevent children or pets from becoming trapped in the drum.
- Dispose of the appliance in accordance with local requirements for the disposal of Waste Electrical and Electronic Equipment (WEEE).
Product description
Appliance overview
- Detergent dispenser drawer
- Control panel
- Door handle
- Rating plate
- Drain pump filter
- Front feet for leveling the appliance
- Drain hose
- Inlet hose connection
- Mains cable
- Back feet for leveling the appliance
- Transit bolts
Rating plate position 4 The data in the following drawing are indicative only. Please check the rating plate of your appliance.
Warning! Before using the appliance, make sure that transit 11 bolts are removed.
Technical data
|
Product type |
Built-in – Washing Machine |
|
|
Dimensions |
Width (cm) |
59.6 |
|
Height (cm) |
81.9 |
|
|
Total depth (cm) |
55.3 |
|
|
Water supply pressure1) |
Minimum |
0,5 bar (0,05 MPa) |
|
Maximum |
8 bar (0,8 MPa) |
If the pressure in your area is lower or higher, please contact your Authorised Service Centre.
Information on the electrical connection, voltage, and overall power is given on the rating plate, on the inner edge of the appliance door.
Electrical connection
At the end of the installation, you can connect the mains plug to the mains socket. The rating plate and the ‘Technical Data’ chapter indicate the necessary electrical ratings. Make sure that they are compatible with the mains power supply.
Check that your domestic electrical installation can take the maximum load required, also taking into account any other appliances in use.
Connect the appliance to an earthed socket.
Inspection checklist
Warning! Refer to Safety chapters.Please follow the inspection checklist before using your appliance.
|
Topics |
If the answer is YES |
If the answer is NO, please |
|
The appliance is built in the furniture following the assembly instructions. It is NOT positioned free-standings. |
|
Install it in the furniture as required. Refer to assembly instruction. |
|
Open and close the detergent dispenser drawer: no collision with furniture. |
|
Refer to ‘Filling the detergent and additives’ section. |
|
Drain hose correctly connected to the drainage. |
|
Refer to hoses connection description in the assembly instruction. |
|
No water leakage around the hose connections. |
|
Refer to water connection warning in the assembly instruction. |
|
The appliance is connected to an earthed socket. |
|
Refer to ‘Electrical connection’ section. |
|
The appliance is stable and levelled properly. |
|
Refer to ‘Installation’ section. |
|
Hoses and mains cable are not kinked. |
|
Refer to ‘Electrical connection’ and ‘Water connection’ section. |
|
There is no carpet under the appliance. |
|
Remove the carpet. |
|
|
||
|
Model (Mod.): …………………Article number (Art.No.): ………………………Serial number (Ser.No.): …………………………. |
Art. No. Mod. Ser. No. |
First use
During installation or before first use you may observe some water in the appliance. This is a residual water left in the appliance after a full functional test in the factory to ensure the appliance is delivered to customers in perfect working order and is no cause for concern.
- Make sure that the electrical power is available and the water tap is open.
- Pour 2 liters of water into the detergent compartment marked by . This action activates the drain system.
- Pour a small quantity of detergent into the compartment marked by.
- Set and start a program for cotton at the highest temperature without any laundry in the drum.This removes all possible dirt from the drum and the tub.
. This action activates the drain system.Control panel
Control panel description
The options/functions are not available with all washing programs. Check the compatibility between options/functions and washing programs in the “Program Chart”. An option/function can exclude another one, in this case, the ap‐ pliance doesn’t allow you to set incompatible options/functions.
|
1 |
|
Press this button for a few seconds to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off. As the Stand-by function automatically deactivates the appliance after several minutes to reduce the energy consumption, press this button to activate the appliance again. For more details, refer to the ‘Stand-by function’ paragraph in the ‘Daily Use’ chapter. |
|
2 |
Program knob |
Turn the selector knob to select the desired program. |
| 3 | Display |  – Indicator on: the door cannot be opened. The appliance is working or has stopped with water left in the tub.– Indicator off: the door can be opened. The program is finished or the water has been emptied out.• Delay start indicator.• 0.00 The digital indicator can show: reset position  ; programme duration (e. g. 2.40); delay time (e. g. 24 ); cycle end (0.00 ); warning code (e.g. E20); error indicator .• —— FlexTime indicator.• Anti-stain indicator.• Extra Rinse indicator.•  Steam phase indicator.•  Add garments indicator. It lights at the beginning of the washing phase when it is still possible to pause the appliance and add more laundry.• Child safety lock indicator.•  Machine clean indicator. This is a recommendation to perform the drum cleaning.•  Anti-crease phase indicator. |
| 4 |
|
With this option, you can delay the start of a program to a more convenient time. Touch the button repeatedly to set the required delay. The time increases in steps of 1 hour up to 20 hours. |
|
5 |
|
With This option reduces the program duration depending on the load size and the degree of soiling.When you set a washing program, the display shows the default duration and the dashes——. Tap on this button to reduce the program duration according to your needs. The display shows the new program duration and the number of dashes will decrease accordingly: —— suitable for a full load of normally soiled garments.—–a quick cycle for a full load of lightly soiled garments.—- very quick cycle for a smaller lightly soiled load (max. half-load recommended).— the shortest cycle to freshen up a small amount of laundry. |
|
6 |
|
This button allows you to start or to pause the selected washing program. |
|
7 |
Anti-stains touch button and permanent Child Lock option |
This option prevents children from playing with the control panel: all controls are disabled. To deactivate this option, hold this button pressed for 3 seconds. |
|
8 |
|
This appliance is designed for saving energy. If it is necessary to rinse the laundry using an extra quantity of water (extra rinse), select this option. Some additional rinses will be performed. This option is recommended for people who are allergic to detergents.
|
|
9 |
|
This option adds a pre-wash phase at 30 °C before the washing phase.This option is recommended for heavily soiled laundry, especially if containing sand, dust, mud and other solid particles. |
This option is designed to remove stubborn stains. Pour the stain remover into the PREWASH compartment.
.
The corresponding indicator above the touch button illuminates and also stays permanently on during the next cycles until this option is deactivated.
|
10 |
|
When you set a program, the appliance automatically sets the maximum spin speed allowed, except in the Denim program. By means of this button, you can change the default spin speed or set one of the additional spin options:
|
|
11 |
|
When you select a washing programme, the appliance automatically proposes a default temperature. With this option you can change the temperature.The indicator of the set temperature comes on. The indicator |
. The related indicator comes on. 
. 
The appliance empties the water out automatically after approximately 18 hours.
Multilingual badges
Adhesive badges in different languages are supplied with the appliance. The desired badge can be glued around the programme knob.
Programmes
Programme Chart
|
Programme Default temperature Temperature range |
Reference spin speed Spin speed range (rpm) |
Max. load |
Programme description (Type of load and level of soiling) |
|
Eco 40-6040 °C 1)60 °C – 30 °C2) |
1400 rpm (1400- 800 rpm) |
8 kg |
White cotton and fast-coloured cotton. Normally soiled items. The energy consumption decreases and the time of the washing programme is extended, ensuring good washing results. |
|
|
1400 rpm (1400 – 800) |
8 kg |
White cotton and coloured cotton. Normal and heavy soil. |
|
|
1200 rpm (1200 – 800) |
3 kg |
Synthetic items or mixed fabric items. Normally soiled items. |
|
|
1200 rpm (1200 – 800) |
2 kg |
Delicate fabrics such as acrylics, viscose and mixed fabrics requiring gentler washing. Normally and lightly soiled items. |
|
|
– |
1 kg |
Steam programme for cotton and synthetic items. This cycle removes odours from the laundry3). |
|
Programme Default temperature Temperature range |
Reference spin speed Spin speed range (rpm) |
Max. load |
Programme description (Type of load and level of soiling) |
|
|
1200 rpm (1200 – 800) |
3 kg |
Synthetic and mixed fabrics. Normally soiled items. |
|
|
1400 rpm (1400 – 800) |
8 kg |
All fabrics, except woollens and delicate fabrics. To spin the laundry and to drain the water in the drum. |
|
|
1400 rpm (1400 – 800) |
8 kg |
All fabrics, except woollens and very delicate fabrics. Programme for rinsing and spinning the laundry. The default spin speed is the one used for cotton programmes. Reduce the spin speed according to the type of laundry. If necessary, set the Extra Rinse option to add rinses. With a low spin speed, the appliance performs delicate rinses and a short spin. |
|
|
1200 rpm (1200 – 800) |
– |
Maintenance cycle with hot water to clean and freshen the drum and to remove residue that may cause odour. For the best result use this cycle once a month. Before running this cycle, remove all items from the drum. In the WASH compartment of the detergent dispenser drawer, turn the flap in upward position. Pour a cup of chlorine bleach or a washing machine cleaner in the washing phase compartment. DO NOT use both together. After the drum cleaning, run a further rinse cycle with empty drum and no detergent to remove any residue of bleach. |
|
|
1200 rpm (1200 – 800) |
3 kg |
Synthetic sport items. This programme is designed to gently wash modern outdoor sportswear and is also suitable for gym, cycling or jogging clothes or similar. |
|
|
800 rpm (1200 – 800) |
3 kg |
Special programme for Denim clothing with delicate washing phase to minimize colour fading and marks. For better care a reduced load size is recommended. |
|
Programme Default temperature Temperature range |
Reference spin speed Spin speed range (rpm) |
Max. load |
Programme description (Type of load and level of soiling) |
|
|
1200 rpm (1200 – 800) |
3 kg |
Cottons and mixed fabrics. Lightly soiled items. Optimal washing results and perfect fabric care in a short time for your everyday laundry. |
|
|
1200 rpm (1200 – 800) |
1.5 kg |
Machine washable wool, hand washable wool and other fabrics with «hand washing» care symbol4). |
|
|
1200 rpm (1200 – 800) |
3 kg |
A very short cycle for lightly soiled cotton and synthetic items or worn only once. |
1) According to Commission Regulation EU 2019/2023, this programme at 40 °C is able to clean normally soiled cotton laundry declared to be washable at 40 °C or 60 °C, together in the same cycle.For the reached temperature in the laundry, the programme duration and other data, please refer to ‘Consumption Values’ chapter.The most efficient programmes in terms of energy consumption are generally those that perform at lower temperatures and longer duration.2) Standard programmes for the Energy Label consumption values. According to EU regulation 1061/2010, this programme at 60 °C is the «Standard 60°C cotton programme» and at 30 °C is the «Standard 40°C cotton programme». They are the most efficient programmes in terms of combined energy and water consumption for washing normally soiled cotton laundry.The water temperature of the washing phase may differ from the temperature declared for the selec‐ ted programme.3) Steam does not remove animal odours.4) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn’t rotate or doesn’t rotate properly, but this is normal for this programme.Programme options compatibility
|
Pro‐ gramme |
|
|
|
|
|
|
|
|
|
|
Eco 40-60 |
■ |
■ |
■ |
|
■ |
■ |
■ |
■ |
■ |
|
|
■ |
■ |
■ |
■ |
■ |
■ |
■ |
■ |
■ |
|
|
■ |
■ |
■ |
■ |
■ |
■ |
■ |
■ |
■ |
|
|
■ |
■ |
■ |
■ |
|
■ |
|
■ |
|
|
|
|
|
|
|
|
|
|
■ |
■ |
|
Pro‐ gramme |
|
|
|
|
|
|
|
|
|
|
|
■ |
■ |
■ |
■ |
■ |
■ |
|
■ |
■ |
|
|
■ |
|
■ |
|
|
|
|
■ |
|
|
|
■ |
■ |
■ |
|
|
■ |
|
■ |
|
|
|
■ |
|
■ |
|
|
|
|
■ |
|
|
|
■ |
■ |
■ |
|
■ |
■ |
|
■ |
|
|
|
■ |
■ |
■ |
■ |
|
■ |
■ |
■ |
|
|
|
■ |
■ |
■ |
■ |
■ |
■ |
■ |
■ |
|
|
|
■ |
■ |
■ |
|
|
|
|
■ |
|
|
|
■ |
|
■ |
|
|
|
|
■ |
|
- Prewash and Stains option cannot be selected together.
- This option is not available with a temperature lower than 40 °C.
Suitable detergents for each programme
|
Programme |
Universal powder1) |
Liquid Universal |
Liquid for coloureds |
Delicates woollens |
Special |
|
Eco 40-60 |
▲ |
▲ |
▲ |
— |
— |
|
|
▲ |
▲ |
▲ |
— |
— |
|
|
▲ |
▲ |
▲ |
— |
— |
|
|
— |
— |
— |
▲ |
▲ |
|
|
— |
▲ |
▲ |
— |
— |
|
|
— |
▲ |
▲ |
— |
▲ |
|
|
— |
— |
▲ |
▲ |
▲ |
|
|
— |
▲ |
▲ |
— |
— |
|
|
— |
— |
— |
▲ |
▲ |
|
|
— |
▲ |
▲ |
— |
— |
1) At temperature higher than 60 °C the use of powder detergent is recommended.
1) At temperature higher than 60 °C the use of powder detergent is recommended.▲ = Recommended — = Not recommended
Settings
Acoustic signals
This appliance has different acoustic signals, that operate when:• You activate the appliance (special short tune).• You deactivate the appliance (special short tune).• You touch the buttons (click sound).• You make an invalid selection (3 short sounds).• The programme is completed (sequence of sounds for about 2 minutes).• The appliance has a malfunction (sequence of short sounds for about 5 minutes).To activate/deactivate the acoustic signals when the programme is completed, touch the
and the
buttons simultaneously for about 2 seconds. The display shows On or Off. If you deactivate the acoustic signals, they continue to operate when the appliance has a malfunction.
Child Lock
With this option you can prevent children from playing with the control panel.To activate/deactivate this option, hold the Anti-stains button pressed until the indicator comes on/goes off on the display.When it is activated, the appliance will default to this option after you switch it off or change/reset the programme. If you press any button, the indicator blinks to indicate that the buttons are disabled.The Child Lock function may not be available for a few seconds after switching the appliance on.
Daily use
Warning! Refer to Safety chapters.
Activating the appliance
- Connect the mains plug to the mains socket.
- Open the water tap.
- Press the On/Off button for a few seconds to activate the appliance.
A short tune sounds.Setting a programme
- Turn the programme knob to select the desired washing programme.The indicator of the Start/Pause button flashes.The display shows an indicative programme duration.
- To change the temperature and/or the spin speed, touch the related buttons.
- If desired, set one or more options by touching the related buttons. The related indicators illuminate.
If a selection is not possible an acoustic signal sounds and the display shows .
Loading the laundry
- Open the appliance door.
- Empty the pockets and unfold the items before you put them in the appliance.
- Put the laundry in the drum, one item at a time.Do not exceed the maximum recommended load for each programme.
- Close the door firmly.Make sure that no laundry gets caught between the seal and the door to avoid risk of water leakage and damage to the laundry.
Warning! Washing heavily oiled, greasy stains could cause damage to rubber parts of the washing machine.
Filling the detergent and additives
PREWASH – Compartment for prewash phase, soak programme or stain remover. The prewash and soak detergent is added at the beginning of the wash programmeWASH – Compartment for washing phase.SOFTENER – Compartment for fabric softener and other liquid treatments (fabric conditioner, starch).MAX – Maximum level for quantity of liquid additives.– Flap for powder or liquid detergent.
Follow the product manufacturer’s recommendations on quantities to use and do not ever exceed the mark in the detergent dispenser drawer. To measure out the right quantity of the detergent, see more details in “Degrees of water hardness”. Any fabric softener or starching additives must be poured into the compartment before starting the wash programme.
After a washing cycle, if necessary, remove any detergent residue from the detergent dispenser drawer.Pull out the detergent dispenser drawer until it stops.
Pour the detergent into the WASH compartment or in the appropriate compartment if it is required by the selected programme/option.For powder detergent: flap turned upwards.
For liquid detergent:
flap turned downwards.With the flap is in the position for liquid detergent:
- Do not use gelatinous or thick liquid detergents.
- Do not exceed to liquid detergent dose indicated on the flap.
- Do not set the pre-wash phase.
- Do not set the delay start function. Pour fabric softener into the compartment marked (do not exceed the mark).Carefully close the detergent dispenser drawer. Make sure that the flap does not block the drawer when closing.
(do not exceed the mark).Carefully close the detergent dispenser drawer. Make sure that the flap does not block the drawer when closing.Setting a programme
- Turn the programme knob to select the desired washing programme.The indicator of the Start/Pause button flashes.The display shows an indicative programme duration.
- To change the temperature and/or the spin speed, touch the related buttons.
- If desired, set one or more options by touching the related buttons. The related indicators illuminate.
If a selection is not possible an acoustic signal sounds and the display shows—–Starting a programmeTouch the Start/Pause
button to start the programme. The related indicator stops flashing and stays on. It is not ossible to start the programme when the indicator of the button is off and doesn’t flash (e.g. programme knob on a wrong position). The programme starts, the door is locked. The display shows the indicator
The drain pump can operate shortly before the appliance fills water.
Starting a programme with the delay start1. 1. Touch the Delay Start button repeatedly until the display shows the desired delay time. On the display the indicator shows2. Touch the Start/Pause button. The appliance door locks and starts the countdown of the delay start. The display shows the indicator.When the countdown is completed, the programme starts automatically. Cancelling the delay start after the countdown has started To cancel the delay start:1. Touch the Start/Pause button to pause the appliance. The related indicator flashes.2. Touch the Delay Start button repeatedly until the display shows and the indicator goes off.3. Touch the Start/Pause button again to start the programme immediately.
Changing the delay start after the countdown has startedTo change the delay start: 1. Touch the Start/Pause button to pause the appliance. The related indicator flashes.2. Touch the Delay Start button repeatedly until the display shows the desired delay time.3. Touch the Start/Pause button again to start the new countdown.
The AutoAdjust System load detectionAfter touching the Start/Pause button:1. The AutoAdjust System starts estimating the weight of the load to calculate the real programme duration. During this phase the indicator placed below the time digits plays a simple animation.2. After about 15-20 minutes the indicator disappears and new cycle duration is displayed. The appliance automatically adjusts the programme duration to the load to achieve perfect washing results in the minimum possible time.
Pausing a programme and changing optionsWhen the programme is running, you can change only some options:1. Touch the Start/Pause button. The related indicator flashes.2. Change the options. The given information in the display changes accordingly.3. Touch the Start/Pause button again. The washing programme continues.
Cancelling a running programme1. Press the button On/Off 
to cancel the programme and to deactivate the appliance.2. Press the button On/Off again to activate the appliance.If the AutoAdjust System has completed and the water filling has already started, the new programme starts without repeating the AutoAdjust System. The water and the detergent are not drained out in order to avoid waste.There is also an alternative way of cancelling: 1. Rotate the programme knob to the “Reset” position.2. Wait for 1 second. The display shows. Now, you can set a new washing programme.
Opening the doorWarning! If the temperature and level of the water in the drum are too high and/or the drum is still rotating you should not open the door.Adding garments. It is recommended to add garments until the is on.While a programme or the delay start operates, the appliance door is locked. The display shows the indicator .1. Touch the Start/Pause button. In the display the related door lock indicator goes off.2. Open the appliance door. If necessary, add or remove the garments. Close the door and touch the Start/Pause button.The programme or the delay start to continue. The door can be opened when the programme is completed, or set the programme to drain the water and then touch the Start/Pause button.programme
to drain the water and then touch the Start/Pause button.End of the programmeWhen the programme has finished, the appliance stops automatically. The acoustic signals operate (if they are active). The display shows 
The indicator of the Start/Pause button goes off.The door unlocks and the indicator goes off.1. Press button On/Off to deactivate the appliance.After five minutes from the end of the programme, the energy-saving function automatically deactivates the appliance.When you activate the appliance again, the display shows the end of the previous programme. Turn the programme knob to set a new cycle.2. Remove the laundry from the appliance.3. Make sure that the drum is empty.4. Keep the door and the detergent dispenser drawer slightly ajar to prevent mildew and odours.
Draining water out after end of cycleIf you have chosen a programme or an option that does not empty out the water of the last rinse, the programme is completed, but:
- The time area shows and the display shows the door locked.
- The indicator of the Start/Pause button starts flashing.
- The drum still turns at regular intervals to prevent creases in the laundry.
- The door stays locked.
- You must drain the water to open the door:
1. If necessary, touch the Spin button to decrease the spin speed proposed by the appliance.2. Press the Start/Pause button: the appliance drains the water and spins. The option indicator
or 
goes off.If you have set and the spin speed has not been changed, when you press the Start/Pause button, the appliance only drains the water.3. When the programme is completed and the door locked indicator goes off, you can open the door.4. Press the On/Off button for a few seconds to deactivate the appliance.
Stand-by functionThe Stand-by function automatically deactivates the appliance to reduce the energy consumption when:• You do not use the appliance for 5 minutes when no programme is running. Press the On/Off button to activate the appliance again.• 5 minutes after the end of the washing programme. Press the On/Off button to activate the appliance again.The display shows the end of the last programme. Turn the programme knob to set a new cycle.If the pris programme knob rotated to the “Reset” position , the appliance automatically turns off in 30 seconds.If you set a programme or an option that ends with water in the drum, the Stand-by function doesn’t deactivate the appliance to remind you to drain the water.
Hints and tips
Warning! Refer to Safety chapters.
The laundry load
- Sort the laundry as follows: white, coloured, synthetics, delicates and wool.
- Follow the washing instructions on the laundry care labels.
- Do not wash white and coloured items together.
- Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first couple of times.
- Button up pillowcases, close zippers, hooks and poppers. Tie up belts.
- Turn multilayered fabrics, wool and items with printed illustrations inside out.
- Pre-treat tough stains.
- Wash heavy soil stains with a special detergent.
- Be careful with curtains. Remove the hooks and put the curtains in a washing bag or pillowcase.
- Do not wash laundry without hems or with cuts.
- Use a washing bag to wash small and/or delicate items (e.g. underwired bras, belts, tights, etc. ).
- Avoid washing garments full of long animal hair or poor quality garments releasing lots of fluff that could block the drain circuit and therefore requiring the Service assistance.
Stubborn stainsFor some stains, water and detergent is not sufficient.We recommend that you pre-treat these stains before you put the items in the appliance.Special stain removers are available. Use the special stain remover that is applicable to the type of stain and fabric.
Do not spray stain remover on garments near the appliance as it is corrosive to the plastic parts.
Detergent type and quantityThe choice of detergent and use of correct quantities not only affects your wash performance, but also helps to avoid waste and protect the environment:
- Use only detergents and other treatments specially made for washing machines. First, follow these generic rules:– powder detergents for all types of fabric, excluding delicate. Prefer powder detergents containing bleach for whites and laundry sanitization,– liquid detergents, preferably for low-temperature wash programmes (60 °C max) for all types of fabric, or special ones for woollens only.
- The choice and quantity of detergent will depend on: type of fabric (delicates, woollens, cottons, etc), the colour of clothes, size of the load, degree of soiling, wash temperature and hardness of the water used.
- Follow the instructions that you find on the packaging of the detergents or other treatments without exceeding the indicated maximum level (MAX ).
- Do not mix different types of detergents.
- Use less detergent if:– you are washing a small load,– the laundry is lightly soiled,– there is large amounts of foam during washing.• When using detergent tabs or pods, always put them inside the drum, not in the detergent dispenser.
Insufficient detergent may cause:
- unsatisfactory washing results,
- the wash load to turn grey,
- greasy clothes,
- mould in the appliance.
Excessive detergent may cause:
- sudsing,
- reduced washing effect,
- inadequate rinsing,
- a greater impact for the environment.
Ecological hintsTo save water, energy and to help protect the environment, we recommend that you follow these tips:
- Normally soiled laundry may be washed without prewash in order to save detergent, water and time (the environment is protected too!).
- Loading the appliance to the maximum capacity indicated for each programmes helps to reduce energy and water consumption.
- With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature.
- To use the correct quantity of detergent, refer to the quantity suggested by the detergent producer and check the water hardness of you domestic system. Refer to ‘Water hardness’.
- Set the maximum possible spin speed for the selected washing programme before drying your laundry in a tumble dryer. This will save energy during drying!
Degrees of water hardnessWater hardness is classified in so-called “degrees” of hardness. Information on hardness of the water in your area can be obtained from the relevant water supply company, or from your local authority.
|
Characteristic |
Degrees of water hardness |
|
|
German °dH |
French °T.H. |
|
|
Soft |
0-7 |
0-15 |
|
Medium |
8-14 |
16-25 |
|
Hard |
15-21 |
26-37 |
|
Very hard |
> 21 |
> 37 |
A water softener must be added when water has a medium-high degree of hardness. Follow the manufacturer’s instructions. The quantity of detergent can then always be adjusted (reduced) to degree of hardness soft.
Care and cleaning
Warning! Refer to Safety chapters.
Periodic cleaning schedulePeriodic cleaning helps to extend the life of your appliance.After each cycle, keep the door and the detergent dispenser slightly ajar to get air circulation and dry the humidity inside the appliance: this will prevent mildew and odours.
If the appliance is not used for a long time: Close the water tap and unplug the appliance.Indicative periodic cleaning schedule:
|
Descaling |
Twice a year |
|
Maintenance wash |
Once a month |
|
Clean door seal |
Every two months |
|
Clean drum |
Every two months |
|
Clean drain pump filter |
Twice a year |
|
Clean the inlet hose and the valve filter |
Twice a year |
The following paragraphs explain how you should clean each part.Removing foreign objectsMake sure that pockets are empty and all loose elements are tied up before running your cycle. Refer to ‘The laundry load’ in ‘Hints and tips.Remove any foreign objects (such as metal clip, buttons, coins, etc) that you may find in the door seal, the filters and the drum. Refer to ‘Door seal with double lip trap’, ‘Cleaning the drum’, ‘Cleaning the drain pump’ and ‘Cleaning the inlet hose and the valve filter’ paragraphs. If necessary, please contact the Authorised Service Centre.External cleaning
Clean the appliance with mild soap and warm water only. Fully dry all the surfaces. Do not use a scouring pads or any scratching material.Caution! Do not use alcohol, solvents or chemical products.Caution! Do not clean the metal surfaces with chlorine-based detergent.DescalingIf the water hardness in your area is high or moderate, we recommend that you use a water descaling product for washing machines.Regularly examine the drum to check for limescale.Regular detergents already contain water softening agents, but we recommend to run a cycle with an empty drum and a descaling product occasionally.Always follow the instructions that you find on the packaging of the product.
Maintenance washThe repeated and prolonged use of low-temperature programmes can cause detergent deposits, fluff residues, bacterial growth inside the drum and the tub. This could generate bad odours and mildew. To eliminate these deposits and clean the inner part of the appliance, run a maintenance wash regularly (at least once a month).Refer to the “Cleaning the drum” paragraph.
Door sealRegularly examine the seal of the door and remove all objects from the inner part.
Cleaning the drumRegularly examine the drum to prevent unwanted deposits.Rust deposits in the drum may occur due to rusting foreign body in the washing or tap water containing ironClean the drum with special products for stainless steel.Always follow the instructions that you find on the packaging of the product. Do not clean the drum with acidic descaling products, scouring products containing chlorine or iron or steel wool.
For a thorough clean:1. Remove all laundry from the drum.2. Run the Machine clean 
programme.For more details, refer to washing programme table.3. Add a small quantity of powder detergent into the empty drum, in order to rinse out any left residues.Occasionally, at the end of a cycle the display may show the icon: this is a recommendation to perform the “drum cleaning”. Once the drum cleaning has been performed, the icon disappears.
Cleaning the detergent dispenser drawer and the drawer recessThe detergent dispenser drawer should be cleaned regularly to remove possible deposits of dried detergent or clotted fabric softener and/or formation of mould. Proceed as follows:
To remove the drawer, press the lever downwards and pull it out.
To aid cleaning, remove also the top part of the additive compartment.
Use a stiff brush to clean and remove all washing powder residue.
Flush out all the removed parts of the dispenser drawer under a tap to remove any traces of accumulated powder.
Use the previous brush to clean the recess, ensuring that upper and lower part of it is well cleaned.
After having cleaned the dispenser and the drawer recess, replace it and run a rinse programme without any laundry in the drum to flush away any residue.Cleaning the drain pumpWarning! Disconnect the mains plug from the mains socket. Regularly check the drain pump filter and make sure that it is clean.
Clean the drain pump if:• The appliance does not drain the water.• The drum does not turn.• The appliance makes an unusual noise because of the blockage of the drain pump.• The display shows the alarm code E20.Warning!• Do not remove the filter while the appliance operates.• Do not clean the pump if the water in the appliance is hot. Wait until the water cools down
Proceed as follows to clean the pump:
- Open the pump cover.
- Place a suitable bowl below the drain pump access to collect the water that flows out.Always keep a rag nearby to dry up any water spillages when removing the filter.
- Turn the filter 180 degrees in an anticlockwise direction to open it, without removing it. Let the water flow out.
- When the bowl is full of water, turn the filter back and empty the container.
- Repeat steps 3 and 4 until the water stops to flow out.
- Turn the filter anticlockwise to remove it.
- If it is necessary, remove fluff and objects from the filter recess.Make sure that the impeller of the pump can rotate. If it does not rotate, contact the Authorised Service Centre.
- Clean the filter under the water tap.
9. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages.10. Close the pump cover.
When you drain the water with the emergency drain procedure, you must activate the drain system again:1. Put 2 litres of water in the main wash compartment of the detergent dispenser drawer.2. Start the programme to drain the water.Cleaning the inlet filter and the filter valveIf the appliance takes long to fill with water or doesn’t fill, the starting button indicator flashes in red. Check if the water inlet filter and the valve filter are blocked (see chapter “Troubleshooting” for more details).Proceed as follows:
- Turn off the water tap.
- Unscrew the hose from the tap.
- Clean the filter in the hose with a stiff brush.
- Screw firmly the inlet hose back onto the tap.
- Unscrew the hose from the appliance. Keep a rag nearby because some water may flow.
- Clean the filter in the valve with a stiff brush or with the piece of cloth.
- Screw the hose back to the appliance turning it to the left or the right to suit the installation. Tight the locknut correctly to prevent water leaks.
- Turn on the water tap.
Emergency drainIf the appliance cannot drain the water, carry out the same procedure, described in ‘Cleaning the drain pump’ paragraph. If necessary, clean the pump.When you drain the water with the emergency drain procedure, you must activate the drain system again:1. Put 2 litres of water in the main wash compartment of the detergent dispenser drawer.2. Start the programme to drain the water.Frost precautionsIf the appliance is installed in an area where the temperature can reach values around 0° C or drop below, remove the remaining water from the inlet hose and the drain pump.
- Disconnect the mains plug from the mains socket.
- Close the water tap.
- Put the two ends of the inlet hose in a container and let the water flow out of the hose.
- Empty the drain pump. Refer to the emergency drain procedure.
- When the drain pump is empty, install the inlet hose again.
Warning! Make sure that the temperature is higher than 0 °C before you use the appliance again.The manufacturer is not responsible for damages caused by low temperatures.
Troubleshooting
Warning! Refer to Safety chapters.
IntroductionThe appliance does not start or it stops during operation.First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre.Warning! Deactivate the appliance before carrying out any check.
In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pause button may flash continuously:
- EH0- The mains supply is unstable. Wait until the mains supply is stable.
- E91- No communication between electronic elements of the appliance. Switch it off and switch on again. The programme was not finished properly or the appliance stopped too early. If the alarm code appears again, contact the Authorised Service Centre.
- E10- The appliance does not fill with water properly. After the proper check, start the appliance again by pressing Start/Pause button the appliance tries to resume the cycle . If the error persists the alarm code will appear again.
- E20- The appliance does not drain the water.
- E40- The appliance door is open or not closed correctly. Please check the door!If the appliance is overloaded, remove some items from the drum and/or hold the door shut while touching the Start/Pause button until the indicator stops flashing (see the picture below).
Possible failures
Possible failures
|
Problem |
Possible solution |
| The programme does not start. |
|
| The appliance does not fill with water properly. |
|
| The appliance fills with water and drains immediately. |
|
| The appliance does not drain the water. |
|
| The spin phase does not operate or the washing cycle lasts longer than usual. |
|
| There is water on the floor. |
|
| You cannot open the appliance door. |
|
| The appliance makes an unusual noise and vibrates. |
|
| The programme duration increases or decreases during programme execution. |
|
| The washing results are not satisfactory. |
|
| Too much foam in the drum during the washing cycle. |
|
| After the washing cycle, there are some detergent residues in the detergent dispenser drawer. |
|
Emergency door openingIn case of power failure or functioning failure the appliance door remains locked. The washing programme continues when the power is restored. If the door remains locked in case of failure, it is possible to open it using the emergency unlock function. Before opening the door:Caution! Risk of burns! Make sure that the water temperature is not too high and the laundry is not hot. If necessary, wait until they cool down.Caution! Risk of injury! Make sure that the drum is not rotating. If necessary, wait until the drum stops rotating.Make sure that the water level inside the drum is not too high. If necessary, proceed with an emergency drain (refer to «Emergency drain» in the «Care and cleaning» chapter).To open the door, proceed as follows:1. Press the On/Off button to switch the appliance off.2. Disconnect the mains plug from the mains socket.3. Pull the emergency unlock trigger downward once. Pull it once again, keep it tensed and, in the meanwhile, open the appliance door. The emergency unlock trigger is located were indicated by the following picture.
4. Take out the laundry and then close the appliance door.
ServiceWe recommend the use of original spare parts. After the check, switch on the appliance and press the button to restart the programme.If the problem remains, contact your Authorised Service Centre. The necessary data for the service centre is on the rating plate. Refer to the ‘Inspection check list’ chapter.
Consumption values
Introduction This user manual reports two different tables in order to favour a gradual passage from regulation to the other:• Regulation EU 1061/2010, valid up to 28th of February 2021, is related to the Energy Efficiency classes from A++ + to D,• Regulation EU 2019/2023, valid from 1st March 2021, is related to the Energy Efficiency classes from A to G set by Regulation EU 2019/2014. See the weblink www.theenergylabel.eu for detailed information about Energy Label.
The QR code on the energy label supplied with the appliance provides a web link to the information related to the performance of the appliance in the EU EPREL database. Keep the energy label for reference together with the user manual and all other documents provided with this appliance. It is also possible to find the same information in EPREL using the link https://eprel.ec.europa.eu and the model name and product number that you find on the rating plate of the appliance. Refer to ‘Product description’ chapter for the position of the rating plate.
Legend
|
kg |
Laundry load. |
h:mm |
Programme duration. |
|
kWh |
Energy consumption. |
°C |
Temperature in the laundry. |
|
Litres |
Water consumption. |
rpm |
Spin speed. |
|
% |
Remaining moisture at the end of spinning phase. The higher is the spin speed, the higher is the noise and the lower is the remaining moisture. |
Values and programme duration may differ depending on different conditions (e.g. room temperature, water temperature and pressure, load size and type of laundry, supply voltage) and also if you change the default setting of a programme.
According to Commission Regulation Eu 2019/2023
|
Eco 40-60 programme |
kg |
kWh |
Litres |
h:mm |
% |
°C |
rpm1) |
|
Full load |
8 |
1.300 |
58 |
3:30 |
52 |
43 |
1351 |
|
Half load |
4 |
0.950 |
46 |
2:40 |
52 |
43 |
1351 |
|
Quarter load |
2 |
0.500 |
35 |
2:40 |
54 |
33 |
1351 |
1) Maximum spin speed.
Power consumption in different modes
|
Off (W) |
Stand-by (W) |
Delay start (W) |
|
0.48 |
0.48 |
4.00 |
|
Time to Off/Standby mode is 15 minutes maximum. |
According to Regulation 1061/2010
|
Standard cotton programmes. |
Load (kg) |
Energy consumption (kWh) |
Water consumption (litres) |
Approximate programme duration (minutes) |
Remaining moisture (%)1) |
|
For Standard 60°C cotton: Set Eco 40-60 at 60°C |
8 |
1.07 |
52 |
260 |
52 |
|
For Standard 60°C cotton: Set Eco 40-60 at 60°C |
4 |
0.79 |
43 |
220 |
52 |
|
For Standard 40°C cotton: Set Eco 40-60 at 30°C |
4 |
0.64 |
43 |
205 |
52 |
1) At the end of spin phase.
|
Off Mode (W) |
Left On Mode (W) |
|
0.48 |
0.48 |
|
The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC . |
Common programmes These values are indicative only.
|
Programme |
kg |
kWh |
Litres |
h:mm |
% |
°C |
rpm1) |
|
Cottons2) 90°C |
8 |
2.20 |
85 |
3:55 |
52 |
85 |
1400 |
|
Cottons 60°C |
8 |
1.50 |
80 |
3:20 |
52 |
55 |
1400 |
|
Cottons3) 20°C |
8 |
0.35 |
80 |
2:35 |
52 |
20 |
1400 |
|
Synthetics 40°C |
3 |
0.75 |
75 |
2:10 |
35 |
40 |
1200 |
|
Delicate4) 30°C |
2 |
0.30 |
50 |
0:50 |
35 |
30 |
1200 |
|
Programme |
kg |
kWh |
Litres |
h:mm |
% |
°C |
rpm1) |
|
Wool 30°C |
1.5 |
0.25 |
65 |
1:05 |
30 |
30 |
1200 |
1) Reference indicator of the spin speed.2) Suitable for washing heavily soiled textiles.3) Suitable for washing lightly soiled cottons.4) It also performs as quick washing cycle for lightly soiled laundry.
Product Information sheet in reference to E.U. regulation 1369/2017
|
Product Information Sheet |
|
|
Trade Mark |
IKEA |
|
Model |
TVÄTTAD, PNC914580232 |
|
Rated capacity in kg |
8 |
|
Energy efficiency class |
A+++ |
|
Energy consumption in kWh per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used. |
196.0 |
|
Energy consumption of the standard 60°C cotton programme at full load in kWh |
1.07 |
|
Energy consumption of the standard 60°C cotton programme at partial load in kWh |
0.79 |
|
Energy consumption of the standard 40°C cotton programme at partial load kWh |
0.64 |
|
Power consumption of the off-mode in W |
0.48 |
|
Power consumption in left-on mode in W |
0.48 |
|
Water consumption in litres per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load. Actual water consumption will depend on how the appliance is used. |
10999 |
|
Spin-drying efficiency class on a scale from G (least efficient) to A (most efficient) |
B |
|
Maximum spin speed in rpm |
1351 |
|
Remaining moisture content in % |
52 |
|
The ‘standard 60 °C cotton programme’ and the ‘standard 40 °C cotton programme’ are the standard washing programmes to which the information in the label and the fiche relates, these programmes are suitable to clean normally soiled cotton laundry and they are the most efficient in terms of combined energy and water consumption. |
– |
|
Programme time of the standard 60°C cotton programme at full load in minutes |
260 |
|
Programme time of the standard 60°C cotton programme at partial load in minutes |
220 |
|
Programme time of the “standard 40°C cotton programme at partial load in minutes |
205 |
|
Duration of the left on mode in minutes |
5 |
|
Airborne acoustical noise emission in db(A) washing |
54 |
|
Airborne acoustical noise emission in db(A) spinning |
72 |
|
Built in appliance Y/N |
Yes |
The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC
Environmental concerns
Recycle materials with the symbol
. Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose ofappliances marked with the symbol
with the household waste. Return the product to your local recycling facility or contact your municipal office.
|
Country |
Phone number |
Call Fee |
Opening time |
|
België |
070 246016 |
Binnenlandse gesprekskosten |
8 tot 20 Weekdagen |
|
Belgique |
Tarif des appels nationaux |
8 à 20. En semaine |
|
|
България |
00359888164080 0035924274080 |
Такса за повикване от страната |
От 9 до 18 ч в работни дни |
|
Česká Republika |
246 019721 |
Cena za místní hovor |
8 až 20 v pracovních dnech |
|
Danmark |
70 15 09 09 |
Landstakst |
man. – fre. 09.00 – 20.00 lør. – søn. 09.00 – 18.00 |
|
Deutschland |
+49 1806 33 45 32* |
* 0,20 €/Verbindung aus d em Festnetz max. 0,60 €/Verbindung aus dem Mobilfunknetz |
Werktags von 8.00 bis 20.00 |
|
Ελλάδα |
211 176 8276 |
Υπεραστική κλήση |
8 έως 20 κατά τις εργάσιμες ημέρες |
|
España |
91 1875537 |
Tarifa de llamadas nacionales |
De 8 a 20 en días laborables |
|
France |
0170 36 02 05 |
Tarif des appels nationaux |
9 à 21. En semaine |
|
Hrvatska |
00385 1 6323 339 |
Trošak poziva 27 lipa po minuti |
radnim danom od ponedjeljka do petka od 08:00 do 16:00 |
|
Ireland |
0 14845915 |
National call rate |
8 till 20 Weekdays |
|
Ísland |
+354 5852409 |
Innanlandsgjald fyrir síma |
9 til 18. Virka daga |
|
Italia |
02 00620818 |
a applicata alle chiamate nazionali |
dalle 8 alle 20 nei giorni feriali |
|
Κυπρος |
22 030 529 |
Υπεραστική κλήση |
8.30 έως 16.30 κατά τις εργάσιμες ημέρες |
|
Lietuva |
5 230 06 99 |
Nacionalinių pokalbių tarifai |
Pr. – Ketv.: 8:00 – 12:00, 12:45 – 17:00 Pnkt.: 8:00 – 12:00, 12:45 – 15:45 |
|
Magyarország |
06-1-252-1773 |
Belföldi díjszabás |
Hétköznap 8.00 és 17.00 óra között |
|
Nederland Luxembourg |
0900 – 235 45 32 (0900-BEL IKEA) 0031 – 50 316 8772 (internationaal) |
Geen extra kosten. Alleen lokaal tarief. |
ma-vr: 8.00 – 21.00 zat: 9.00 – 21.00 zon / pub. vakantie: 10.00 – 18.00 |
|
Norge |
22 72 35 00 |
Takst innland |
8 til 20 ukedager |
|
Österreich |
+43-1-2056356 |
max. 10 Cent/min. |
Mo – Fr 8.00 – 20.00 Uhr |
|
Polska |
801 400 711 |
Stawka wg taryfy krajowej |
Od 8 do 20 w dni robocze |
|
Portugal |
211557985 |
Chamada Nacional |
9 às 21. Dias de Semana *excepto feriados |
|
România |
021 211 08 88 |
Tarif apel naţional |
8 – 20 în zilele lucrătoare |
|
Россия |
8 495 6662929 |
Действующие телефонные тарифы |
с 8 до 20 по рабочим дням Время московское |
|
Schweiz |
031 5500 324 |
Tarif für Anrufe im Bundesgebiet |
8 bis 20 Werktage |
|
Suisse |
Tarif des appels nationaux |
8 à 20. En semaine |
|
|
Svizzera |
a applicata alle chiamate nazionali |
dalle 8 alle 20 nei giorni feriali |
|
|
Slovenija |
38618108621 |
lokalni strošek je običajna tržna vred- nost, odvisna od ponudnika telefonije |
8.00 – 16.00 ob delavnikih |
|
Slovensko |
(02) 3300 2554 |
Cena vnútroštátneho hovoru |
8 až 20 v pracovných dňoch |
|
Suomi |
030 6005203 |
Lankapuhelinverkosta 0,0835 €/puhelu + 0,032 €/min Matkapuhelinverkosta 0,192 €/min |
arkipäivisin 8.00 – 20.00 |
|
Sverige |
0775 700 500 |
lokalsamtal (lokal taxa) |
mån-fre 8.30 – 20.00 lör-sön 9.30 – 18.00 |
|
United Kingdom |
020 3347 0044 |
National call rate |
9 till 21. Weekdays |
|
Србија |
+381 11 7 555 444 (ако позивате изван Србије) 011 7 555 444 (ако позивате из Србије) |
Цена позива у националном саобраћају |
Понедељак – субота: 09 – 20 Недеља: 09 – 18 |
|
Eesti, Latvija, Україна |
IKEA TVATTAD User Manual – IKEA TVATTAD User Manual –
[xyz-ips snippet=”download-snippet”]