NEDDRAGEN
Your safety and the safety of others are very important.We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.All safety messages will follow the safety alert symbol and either the word “WARNING” or “CAUTION.”
IMPORTANT INSTALLATION INFORMATION
- All electric cooktops run off a single phase, three-wire or four-wire cable, 240/208 volt, 60 hertz, AC only electrical supply with ground.
- Minimum distance between cooktop and overhead cabinetry is 30″ (76.2 cm).
|
MODEL |
A. LENGTH |
B. WIDTH |
C. DEPTH |
CUTOUT DIMENSIONS |
F. DEPTH BELOW COOKTOP* |
|||
|
D. LENGTH |
E. WIDTH |
|||||||
|
MIN. |
MAX. |
MIN. |
MAX. |
|||||
|
30″ |
30″ (76.2 cm) |
213/8” (54.4 cm) |
25/8” (6.7 cm) |
28½” (72.4 cm) |
297/8” (75.9 cm) |
195/8” (49.9 cm) |
20½” (52.1 cm) |
5″ (12.7 cm) |
All dimensions are in inches (cm). Only some models are available in Canada.
*Allow 2″ (5 cm) space below cooktop to clear the electric cable and allow for installation of the junction box on the wall at the back of the cooktop.
Caution:
To eliminate the risk of burns or fire by reaching over heated surfaces, cabinet storage space located above the cooktop should be avoided. If cabinet storage is provided, risk can be reduced by installing a range hood that projects horizontally a minimum of 5″ (12.7 cm) beyond the bottom of the cabinets.
COUNTERTOP CUTOUT OPENING
Important Notes to the Installer
- Read all instructions contained in these installation instructions before installing the cooktop.
- Remove all packing material before connecting the electrical supply to the cooktop.
- Observe all governing codes and ordinances.
- Be sure to leave these instructions with the consumer.
- All materials used in construction of cabinets, enclosures, and supports surrounding the product must have a temperature rating above 194°F (90°C).
Important Note to the Consumer
Keep these instructions with your User manual for future reference.
IMPORTANT SAFETY INSTRUCTIONS
- Be sure your cooktop is installed and grounded properly by a qualified installer or service technician.
- These cooktops must be electrically grounded in accordance with local codes or, in their absence, with the National Electrical Code ANSI/NFPA No. 70—latest edition in the United States, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, in Canada.
Observe all governing codes and local ordinances
- A 3-wire or 4-wire single phase 120/240 or 120/208 Volt, 60 Hz AC only electrical supply is required on a separate circuit fused on both sides of the line (red and black wires). A time- delay fuse or circuit breaker is recommended. DO NOT fuse neutral (white wire). Only certain cooktop models may be installed over certain built-in electric oven models. Approved cooktops and built-in ovens are listed by the MFG ID number (see the insert sheet included in the literature package).
- The flexible armored cable extending from the appliance should be connected directly to the junction box. The junction box should be located as shown in Figure 1 or Figure 2 and with as much slack as possible remaining in the cable between the box and the appliance, so it can be moved if servicing is ever necessary.
- A suitable strain relief must be provided to attach the flexible armored cable to the junction box.
NOTE: Wire sizes and connections must conform with the fuse size and rating of the appliance in accordance with the American National Electrical Code ANSI/NFPA No. 70-latest edition, or with Canadian CSA Standard C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.
Install the junction box under the cabinet and run 120/240 or 120/208 Volt, AC wire from the main circuit panel. DO NOT connect the wire to the circuit panel at this time.
Electrical Requirements
This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse. A circuit breaker or fuse is required by your appliance. The circuit breaker or fuse amperage recommended for your appliance is 40A or 50A.
Unpacking Instructions
- Leave corner supports on cooktop until completion of Electrical Connection.
- It is important that the ceramic-glass smooth top be pretreated before use.
Electrical Connection
It is the responsibility and obligation of the consumer to contact a qualified installer to assure that the electrical installation is adequate and is in conformance with the National Electrical Code ANSI/ NFPA No. 70-latest edition, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.
NOTE TO ELECTRICIAN: The armored cable leads supplied with the appliance are UL-recognized for connection to larger gauge household wiring. The insulation of the leads is rated at temperatures much higher than temperature rating of household wiring. The current carrying capacity of the conductor is governed by the temperature rating of the insulation around the wire, rather than the wire gauge alone.
RISK OF ELECTRIC SHOCK: Grounding through the neutral conductor is prohibited for new branch- circuit installations (1996 NEC); mobile homes; recreational vehicles; or in Canada, or in an area where local codes prohibit grounding through the neutral connector.
If your appliance is not equipped with a white neutral conductor: Connect only to a 3-wire, 120/240V power supply; the neutral conductor is not required for the operation of the appliance. The potential at the power supply electrical connections shall be 150V to ground or less.
Your appliance has a 3-wire cable to be connected to a 3-wire grounded junction box (see figure 4):
- Disconnect the power supply.
- In the circuit breaker, fuse box or junction box: Connect appliance and power supply cable wires as shown in figure 4.
Your appliance has a 4-wire cable to be connected to a 3-wire grounded junction box (see figure 5):
- Disconnect the power supply.
- In the junction box:Connect appliance and power supply cable wires as shown in Figure 5.
Your appliance has a 3-wire cable to be connected to a 4-wire grounded junction box (see figure 6):
- Disconnect the power supply.
- Separate the green (or bare copper) and white appliance cable wires.
- Cap the white wire from the power supply cable if a 3-wire appliance cable is supplied.
- In the circuit breaker, fuse box or junction box:
- Connect appliance and power supply cable wires
Cooktop Installation
- Visually inspect the cooktop for damage. Also make sure all cooktop screws are tight (see Figure 8).
- Set the cooktop into the countertop cutout.
During the installation with wide cutout, make sure the cooktop is centered. A and B gap should have the same dimensions. The elongated holes on the bottoms of the installation brackets are made to fit every cutout.
Warning
Do not remove the built in springs on the edges of the cooktop. These springs center the cooktop in the space provided. The cooktop must be centered to prevent excess heat buildup that may result in heat damage or fire
Hard countertop installation
If installing this cooktop into a granite, marble, or other hard countertop, make sure to perform the following operations:
- Use a heatproof adhesive specified for the material of your countertop.
- Tape the brackets (by the top of the bracket) exactly where they are supposed to be according to the installation instructions (use duct tape, or similar adhesive tape).
- Lift the brackets and apply a generous amount of adhesive on the lip portion of the countertop.
- Apply enough adhesive for there to be excess adhesive that will flow/push through all of the holes in the brackets.
- Apply the brackets to the adhesive on the countertop, as shown in the diagram.
- Visually verify that the excess adhesive has pushed through all of the holes in the bracket.
- Do not remove the excess adhesive that has flowed/pushed through the bracket holes. Once cured, this excess adhesive will provide additional support for the brackets.
- Allow to the adhesive to cure for the minimum time prescribed by the adhesive manufacturer. You will find this information on the external surface of the adhesive container.
- Remove all the duct tape from the installation.
- Install the cooktop in place, as specified in the diagram, and secure with mounting screws.
Checking Operation
Refer to the User manual for operation.
Model and Serial Number Location
The rating plate is located under the cooktop or in the burner box and can be seen by lifting up the main top of unit. When ordering parts for or making inquires about your cooktop, always be sure to include the model and serial numbers and a lot number or letter from the rating plate on your cooktop.
Before You Call for Service
Read the Avoid Service Checklist and operating instructions in your User manual. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. Refer to the warranty in your User manual for our service phone number and address. Please call or write if you have inquiries about your product and/ or need to order parts.
For typical under counter installation of an electric built-in oven
Only certain cooktop models may be installed over certain built-in electric oven models. Approved cooktops and built-in ovens are listed by the MFG ID number and product code (see the insert sheet included in the literaturepackage and cooktop installation instructions for dimensions).
IKEA NEDDRAGEN Installation Instruction – IKEA NEDDRAGEN Installation Instruction –
[xyz-ips snippet=”download-snippet”]