DESIGNED TO WORK FOR YOU
Weather Thermometermode/#00609Instruction Manual
Overview
Introduction
Thank You for purchasing this Acurite® product. Please read through this manual in it’s entirety to fully enjoy the benefits and features of this product. Please keep this manual for future reference.NOTE: A clear film is applied to the LCD at the factory that must be removed prior to using this product. Locate the clear tab and simply peel to remove.
SETUP
Battery Choice & Temperature RangeExtended periods of cold temperatures ( below -4°F / -20°C ) can cause alkaline batteries to function improperly. This will cause the outdoor wireless sensor to stop transmitting temperature readings. Use lithium batteries in these low-temperature conditions to ensure continued operation for wireless sensors placed outdoors. NOTE: Rechargeable batteries are not recommended due to higher operating voltages.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Removebattteriesfrom equipment which is not to be used for an extended period of lime. Follow the polarity(+/-) diagram in the battery compartment. promptly removedead batteries from the device. Dispose of used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries.DONOTdisposeof batteries in a fire. as batteries may explode or leak. DO not mix old and new batteries or types of batteries (alkaline/standard). NOT DO use rechargeable DO recharge batteries. NOT non-rechargeable DO short-circuit the supply terminals.A/B/C Wireless SelectionTo allow for more than one display and wireless sensor network to be used in close proximity, the display unit, and the wireless sensor has a small switch labeled “A B C” within the battery compartments. This switch selects one of 3 wireless modes to use, and both switches MUST be set in matching positions (either A, B, or C) for wireless communication to take place successfully.
Installing Batteries – Wireless Sensor
Remove the battery compartment cover. Install 2 fresh “AA” batteries as shown here. BATTERIES MUST BE INSTALLED FORTHE SENSOR TO OPERATE
Installing Batteries – Display Unit
Remove the battery compartment cover.Install 3 fresh “AA” batteries into the battery compartment.Replace the battery compartment cover.
PLACEMENT
Now that setup is complete, you must choose a location to place the wireless sensor and the display unit. The wireless sensor MUST be placed less than 330 feet ( 100 meters} away from the display unit.This wireless thermometer uses radiofrequency for communication, which is susceptible to interference from other electronic devices and large metallic items or thick walls. Always place both units at least 3 feet (.91 m} away from appliances ( TV, microwave, radios, etc. } or objects that may interfere with the wireless communication ( large metal surfaces, thick stone walls, etc. ).
Placement of Display UnitPlace the display unit in a dry area free of dirt and dust. To help ensure an accurate indoor temperature and humidity measurement, be sure to place the display unit out of direct sunlight, and away from any heat sources or vents in your home. There are 2 placement options for the display unit. You may hang the main unit on a wall using the integrated hang hole. Alternatively, you may place the main unit on a tabletop or other flat surface using the included detachable tabletop display stand.
Placement of SensorThe wireless sensor MUST BE PLACED OUTDOORS to observe outdoor temperatures and humidity. The wireless sensor must be placed less than 330 feet ( 100 m) from the display unit. The wireless sensor is water-resistant and is designed for general outdoor use.However, to extend the life of the product, place the wireless sensor ‘life in an area protected from direct weather elements.To ensure an accurate outdoor temperature measurement, be sure the wireless sensor is placed out of direct sunlight and away from any heat sources.There are 2 placement options for the wireless sensor. You may hang it using one of the two integrated hang holes, or use string (not included) to hang it from a suitable location like a well-covered tree branch.
USE
Main Unit Detachable Stand
Included with the main unit is a detachable stand for tabletop placement.
Features
TROUBLESHOOTING
| Problem | Possible Solution |
Bad Wireless Sensor Reception no bars |
Relocate the main unit and/or the wireless sensor. Both units must be within 330 feet (100m) from each other. Make sure both units are placed at least 3 feet (.91 m) from other electronic appliances and devices that may interfere with the wirelesscommunication (such as TVs, microwaves, computers, etc). NOTE: It may take up to 20 minutes for the main unit to re-synchronize with the sensor when batteries are replaced. Use lithium batteries in the sensor when the temperature is below -4°F (-20°C). |
No Wireless Sensor Data(no communication) no bars and flashing e ” – ” data |
If wireless reception is bad (no bars), see the “Bad Reception” section above. The wireless ID setting on each unit must match for all units to communicate properly. See “Set Wireless ID” on the next page. |
| Display ConsoleScreen Not Working | Make certain that the batteries are installed correctly.Batteries may need replacing |
Please DO NOT return the product to the retail store.For technical assistance and product return information, please call Customer Care: 877-221-1252 Mon. – Fri. 8:00 A.M. to 4:30 P.M. ICST] www.chaneyinstrument.com
Set Wireless ID
This wireless thermometer uses a long-range 433mhz radio frequency for communication.In the event that you have reception problems due to interference, both the display unit and the wireless sensor have a selectable wireless ID.The ID switches are located within the battery compartments of the display unit and the wireless sensor.You may choose A, B or C; but both the display unit and the wireless sensor IDs must match for successful synchronization.
SPECIFICATIONS
Product FactsBatteries: 5 x “AP:’ (not included) Lithium Batteries Recommended in Outdoor Sensor if temperatures are below-4°F
Measurement Ranges
| color Temperature: -40°F to 158°F -40°C to 70°C |
| Outdoor Humidity: 1% to 99% RH |
| Indoor Temperature: 32°F to 122°F 0°C to 50°C |
| Indoor Humidity: 16% to 98% RH |
| Wireless Range: 330 ft / 100 m MAXDepending on home construction materials |
MADE IN CHINAHECHO EN CHINALimited OneYear WarrantyInstructions&Warranty EnclosedCustomer Care:877-221-1252www.chaneyinstrument.com
LIMITED ONE YEAR WARRANTYChaney Instrument Company warrants that all products it manufactures be of good material and workmanship and to be free of defects if properly installed and operated for a period of one year from the date of purchase. REMEDY FOR BREACH OF THIS WARRANTY IS EXPRESSLY LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE ITEMS. Any product which, under normal use and service, is proven to breach the warranty contained herein within ONE YEAR from the date of sale will, upon examination byChaney, and at its sole option, be repaired or replaced by Chaney. In all cases, transportation costs and charges for returned goods shall be paid for by the purchaser. Chaney hereby disclaims all responsibility for such transportation costs and charges.This warranty will not be breached, and Chaney will give no credit for products it manufactures which shall have received normal wear and tear, been damaged, tampered with, abused, improperly installed, damaged in shipping, or repaired or altered by others than authorized representatives of Chaney.THE ABOVE-DESCRIBED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND ALL OTHER WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. CHANEY EXPRESSLY DISCLAIMS ALL LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES, WHETHER ARISING IN TORT OR BY CONTRACT FROM ANY BREACH OF THIS WARRANTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. CHANEY FURTHER DISCLAIMS ALL LIABILITY FROM PERSONAL INJURY RELATING TO ITS PRODUCTS TO THE EXTENT PERMITTED BY LAW. BY ACCEPTANCE OF ANY OF CHANEY”S EQUIPMENT OR PRODUCTS, THE PURCHASER ASSUMES ALL LIABILITY FOR THE CONSEQUENCES ARISING FROM THEIR USE OR MISUSE. NO PERSON, FIRM OR CORPORATION IS AUTHORIZED TO ASSUME FOR CHANEY ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF ITS PRODUCTS. FURTHERMORE, NO PERSON, FIRM OR CORPORATION IS AUTHORIZED TO MODIFY OR WAIVE THE TERMS OF THIS PARAGRAPH, AND THE PRECEDING PARAGRAPH, UNLESS DONE IN WRITING AND SIGNED BY A DULY AUTHORIZED AGENT OF CHANEY. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
For in-warranty repair, please contact:Customer Care DepartmentChaney Instrument Company965 Wells StreetLake Geneva, WI 53147
Chaney Customer Care877-221-1252Mon-Fri 8:00 a.m. to 4:30 p.m. CSTwww.chaneyinstrument.com
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:1- This device may NOT cause harmful interference, and2- This device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Current the equipment into an outlet on a circuit different from that to which the receiver 1s connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
06095B 060111
Patent numbers: 5,978,738; 6,076,044; 6,597,990; US 7,637,141 B2 ACURITE® is a registered trademark of the Chaney Instrument Co.Lake Geneva, WI
References
[xyz-ips snippet=”download-snippet”]