Instruction Manual
Professional Weather Centermodel 01502
Questions? Contact Customer Support at(877) 221-1252 or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference.
Unpacking Instructions
Remove the protective film that is applied to the LCD screen prior to using this product. Locate the tab and peel off to remove.
Package Contents
- Display unit with tabletop stand
- 5-in-1 sensor
- Sensor mounting bracket
- Mounting hardware
- Snap-in debris filter for rain collector
- Instruction Manual
Features & Benefits
5-IN-1 SENSOR
- Rainfall Collector Funnel
- Solar Cell PanelConverts sunlight into power to run internal aspirating fan. Internal Aspirating Fan (not shown)Draws ambient air into sensor to reduce solar radiation heating, resulting in more accurate temperature measurement.
- A-B-C SwitchID code that must match displayʼs A-B-C switch to ensure units synchronize.
- Battery Compartment
- Temperature & Humidity Sensors (internal)
- Mounting Point
- Wind Speed Anemometer
- Wind Direction Vane
- Mounting Bracket
- Mounting HardwareIncludes anchors and screws.
Qty Diameter Length 4 #4 1” 2 #6 ½” - Debris filterSnaps into rain collector to filter out twigs, leaves, etc.
Features & Benefits
Display Unit
DISPLAY UNIT
- Peak Wind SpeedHighest speed from past 60 minutes.
- Average Wind Speed of all speeds from past 2 minutes.
- Pressure History GraphCurrent pressure on right with trend (Rising, Steady or Falling).
- Historical Barometric PressurePressure reading 12 hours ago.
- Weather SelectHeat index, dew point, wind chill, indoor temperature / humidity, and rainfall rate (inches of rain per hour)
- Wireless Sensor Signal Strength
- Alarm On/Off Indicator for Selectable Category (23)
- Programmable Alarm Settings
- Current Outdoor Temperature Arrow icon indicates direction the temperature is trending.
- Outdoor Temperature Alarm On Indicator
- Current Outdoor HumidityArrow icon indicates the direction the humidity is trending.
- Outdoor Humidity Alarm On Indicator
- 12 to 24 Hour Weather ForecastSelf-Calibrating Forecasting pulls data from your 5-in-1 sensor to generate your personal forecast.
- Learning Mode IconDisappears after weather forecast self-calibration is complete.
- Storm Alert Alarm On Indicator
- Current RainfallAccumulates data during rainfall.
- Rainfall Alarm On Indicator
- All-Time Rainfall
- Current Month Total Rainfall
- Date
- Record HighsShown for current category selected on the display (23).
- Record LowsShown for current category selected on the display (23).
- Selectable Category
- Previous 2 Wind Directions
- Current Wind Direction
- Current Wind Speed
- Wind Speed Alarm On Indicator
- Clock
- Weather Select ButtonPress to change the Weather Select category data being display.
- Alarm On/Off ButtonActivate alarm; press and hold to adjust alarm values.
- Select Category (shown in 23) & Change Settings
- Settings Button
- All-Time Records ButtonPress for all-time low and date recorded for current category selected on display (23). Press twice for all-time high and date recorded.
- Clear Button Deletes record high (21) shown.
- Clear Button Deletes record low (22) shown. BACK OF DISPLAY UNIT (in battery compartment)
- A-B-C Switch (not shown) ID code that must match 5-in-1 sensorʼs A-B-C switch to ensure units synchronize.
- Clear Today (not shown) Clears data recorded since 12:00am.
- Clear All (not shown) Clears all data recorded.
- Reset (not shown) Full reset to factory defaults.
SETUP
•5-in-1 Sensor Setup
1. Install or Replace Batteries Batteries MUST be installed for this product to operate. AcuRite recommends high quality alkaline or lithium batteries for the best product performance. Heavy duty or rechargeable batteries are not recommended.
The 5-in-1 sensor requires lithium batteries in low temperature conditions. Cold temperatures can cause alkaline batteries to function improperly. Use lithium batteries in the 5-in-1 sensor for temperatures below -4ºF / -20ºC.1. Slide off the battery compartment cover.2. Insert 4 x AA batteries into the battery compartment, as shown.Follow the polarity (+/-) diagram in the battery compartment.3. Replace the battery cover.
2.2 Remove Rain Gauge StabilizerLocate and remove the rain gauge stabilizer (plastic tab) taped into the bottom of the sensor. The rain gauge will not function until this is removed.
3.3 Set the A-B-C SwitchLocate the A-B-C switch inside the battery compartment. Set the A-B-C switch to A, B or C. You must select the same letter choices for both the sensor and the display unit in order for the units to synchronize.
Display Unit Setup
- Install or Replace Batteries1. Slide off the battery compartment cover.2. Insert 3 x AA alkaline batteries into the battery compartment, as shown. Follow the polarity (+/-) diagram in the battery compartment.3. Replace the battery cover.
- Set the A-B-C SwitchLocate the A-B-C switch inside the battery compartment. Set the A-B-C switch to A, B or C. You must select the same letter choices for both the display unit and the sensor in order for the units to synchronize.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.
Set the Time & Date
The clock and calendar are utilized to time stamp history records and other data, so it is important to set the time and date soon after you power on thedisplay unit.
Set the Time
1. Press the up or down arrow buttons until “SET CLOCK?” is displayed on the Selectable Category part of the display unit.2. Press the 
button to set the clock.3. Press the up or down arrows to adjust the hour. Note the “AM” and “PM” indicators.4. Press the button to confirm hour selection.5. Press the up or down arrows to adjust minutes.6. Press the button to confirm minute selection.The clock is now set.
Set the Date1. Press the up or down arrow buttons until “SET DATE?” is displayed on the Selectable Category part of the display unit.2. Press the button to set the date.3. Press the up or down arrows to adjust the month.4. Press the button to confirm month selection.5. Press the up or down arrows to adjust the day.6. Press the button to confirm day selection.7. Press the up or down arrows to adjust the year.8. Press the button to confirm year selection.The date is now set.
Select Measurement UnitsTo select between standard units (mph, ºF, etc.) or metric units (kph, ºC, etc.):
- Press the up or down arrow buttons until “SET UNITS?” is displayed on the Selectable Category part of the display unit.
- Press the
button to set the unit preference. - Press the up or down arrows to select “STAND” for standard or “METRIC” for metric units.
- Press the button to confirm your selection.
- Next, you will see “WIND MPH”. Press the up or down arrows to select MPH, KPH, or KNOTS for wind speed units.
- Press the button to confirm your selection.Units are now set.
Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper placement of both the display unit and the sensor are critical to the accuracy and performance of this product.
Display Unit PlacementPlace the display unit in a dry area free of dirt and dust. To ensure accurate temperature measurement, place out of direct sunlight and away from heat sources or vents. Display unit stands upright for tabletop use or is wall-mountable.
5-in-1 Sensor PlacementThe 5-in-1 sensor is designed to remain outdoors all year long.Choose an open location with no obstructions above or around the sensor for the most accurate measurements.
Important Placement GuidelinesDisplay unit and sensor must be within 330ft (100m) of each other.MAXIMIZE WIRELESS RANGEPlace units away from large metallic items, thick walls, metal surfaces, or other objects that may limit wireless communication.PREVENT WIRELESS INTERFERENCEPlace both units at least 3ft (.9m) away from electronic devices (TV, computer, microwave, radio, etc.).LOCATE AWAY FROM HEAT SOURCESPosition sensor away from heaters, air conditioners, chimneys, exhaust vents, asphalt and concrete (surfaces that radiate heat).LOCATE AWAY FROM HUMIDITY SOURCESAvoid installing the sensor near pools, spas, or other bodies of water. Water sources may impact humidity accuracy.LOCATE AWAY FROM SPRINKLER HEADSDO NOT install the sensor where it will be sprayed by a sprinkler system. This impacts rainfall measurement accuracy and may force water inside the sensor.LOCATE AWAY FROM WIND & RAIN OBSTRUCTIONSDO NOT mount the sensor with obstructions above it, as this will impact rainfall measurement. Consider a location that is a wide open area, with few structures around to ensure accurate wind speed and direction measurements.
Visit us online to view installation photos and video, or learn more about AcuRite technology: www.AcuRite.com/5in1
View Video : http://www.acurite.com/5in1?utm_source=01502BPDI&utm_medium=qr&utm_campaign=Instructions
5-in-1 Installation GuidelinesINSTALLATION HEIGHT Mount the sensor at least 5 feet (1.5 meters) off the ground (higher is better for wind measurement) in an open area. Secure to fence post, 2”x4“ wood, 3/4” pipe, etc. (not included)LEVEL INSTALLATION Use the bubble level on the top of the sensor to ensure level installation for accurate wind and rain measurement.SOLAR CELL ORIENTATION Install the sensor with the solar cell facing SOUTH. This ensures the cell receives as much sun as possible, and orients wind direction.
5-in-1 Sensor Installation1. Fasten mounting base (included) to a post or pole (not included) using the 4 longer screws included in the hardware bag.2. Insert the mounting base into the hole on the bottom of the sensor.3. Make sure the arrows on the top of the sensor are pointed in the proper direction and the bubble level is centered. The solar cell should be facing south to properly orient the wind direction vane.3. Fasten the sensor into the mounting base using the 2 shorter screws included in the hardware bag.The 5-in-1 sensor is now ready to use.
Clear Data Collected During InstallationWhen installation is complete, clear erroneous data from the display unit by pressing the “CLEAR TODAY” button, on the back of the display unit inside the battery compartment. This button will clear data recorded since 12:00am.Basic Setup is CompleteThe 5-in-1 sensor will now synchronize with the display unit. It may take a few minutes for synchronization to complete. If both or one of the units appear to be functioning improperly, please refer to the troubleshooting section.
OPERATION
Using the Professional Weather Center
Learning ModeSelf-Calibrating Forecasting use a unique algorithm to analyze changes in pressure and temperature over a time period (called Learning Mode) to determine your altitude. After 14 days, the Learning Mode icon disappears from the display screen. At this point, the self-calibrated pressure is tuned in to your location and the unit is ready for superior weather prediction.
View the complete list of icons at www.AcuRite.com/acurite-icons
Weather ForecastAcuRiteʼs patented Self-Calibrating Forecasting provides your personal forecast of weather conditions for the next 12 to 24 hours by collecting data from the sensor in your backyard. It generates a forecast with pinpoint accuracy – personalized for your exact location.
Barometric PressureSubtle variations in barometric pressure greatly affect the weather. This weather forecaster displays the current pressure, direction it’s trending (FALLING, STEADY, or RISING) and a pressure chart. The chart tracks and displays the change in pressure so you can monitor the rate of change over time.Rainfall EventThe rainfall feature tracks rain accumulation over all-time, the current month, and current rainfall event. Current event clears when no rain registers for 8 hours OR no rain registers for 1 hour and pressure rises by .03inhg or more.Programmable Weather AlarmsEach Selectable Weather Category features an alarm option. When an alarm sounds, the display unit emits an audible beeping and flashes the affected category, its alarm settings, and any other relevant data.
Some alarms can be customized to alert you when your programmed value is reached. Alarms include: outdoor temperature, outdoor humidity, wind speed, heat index, dew point, wind chill, indoor temperature and indoor humidity.The rain alarm does not require a preset numerical value, but instead sounds as soon as rain is recorded. Similarly, the storm alarm sounds when a large atmospheric pressure drop occurs, which usually indicates an oncoming storm.Note: The storm alarm is NOT intended to be a safety device or warning system.
Set a Weather Alarm
- Choose the weather category for which you wish to set an alarm by pressing the up or down arrow buttons until the category is displayed on the Selectable Category part of the display unit.
- To program a value (only applies to alarms that require a value), press AND HOLD the button until the “SET” indicator appears in the area of the display labeled “ALARM” (left of the selected weather category) and the alarm setting flashes.
- Adjust the alarm value by pressing the up or down arrow buttons.
- Press the button to confirm a value.
- Next, press the button to activate the alarm. The alarm ON indicator will highlight on the display.Alarm is now programmed and turned on.
button until the “SET” indicator appears in the area of the display labeled “ALARM” (left of the selected weather category) and the alarm setting flashes.
Silence a Sounding AlarmThe alarm sounds initially for a few minutes, then silences itself. The alarm then sounds every few minutes afterwards until one of the following happens:1. “SNOOZE” – Press any button. Alarm silences, but sounds again if the alarm condition reoccurs.2. Turn the alarm “OFF” – Deactivates the alarm.
Troubleshooting
| Problem | Possible Solution |
No outdoor sensor reception |
|
| Outdoor temperature is flashing orshowing dashes | Flashing of the outdoor temperature may be an indication of wireless interference.• Make sure the A-B-C switch in the battery compartments of both the display unit and sensor are switched to the same letter. You may choose A, B or C; but both units must match for successful synchronization. |
| Display screen not working | • Check that the batteries are installed correctly. Batteries may need to be replaced.• Reset the display by pressing the reset button, located on the back of the display unit. Date and time will need to be entered after a reset. |
| Inaccurate forecast (Continued on p.15) | • The Weather Forecast icon is a prediction of conditions for the next 12 to 24 hours. It is not showing current conditions. |
| Inaccurate forecast (Continued from p.14) |
|
| Inaccurate temperature or humidity |
|
| No rainfall |
|
| Inaccurate wind readings |
|
If your AcuRite product does not operate properly after trying the troubleshooting steps, visit www.AcuRite.com or call (877) 221-1252 for assistance.
Care & Maintenance
Display Unit CareClean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep away from dust, dirt and moisture. Clean ventilation ports regularly with a gentle puff of air.5-in-1 Sensor CareClean The SensorClean with a soft damp cloth. Do not use caustic cleaners or abrasives that will mar the polished surfaces of the rain collection funnel or the solar cell. Scratches will result in decreased performance and reliability.Insect PreventionInsects may cause obstructions and interrupt data by nesting in or on the 5-in-1 sensor. To limit this problem, spray sensor with a household insect repellent. Consult the insect repellent instructions prior to use.Snow & Freezing WeatherThe 5-in-1 sensor will not be damaged by freezing conditions. NOTE: If the rain collector cup fills with snow and then melts, it will register as rain on the display unit.Clean The Rain Collector CupRemove and empty rain collector debris filter. The debris filter is located in the rain collector funnel. Remove from the top by gently squeezing and pulling out.Clean the Wind Vane & AnemometerRemove foreign matter from the outside of the sensor for free movement of the wind vane and anemometer. If needed, use a small amount of spray lubricant, clear silicone or graphite powder on the anemometer for improved movement.
Calibration
Calibrate Temperature & HumidityThe indoor / outdoor temperature and humidity readings can be calibrated on the display unit to improve accuracy. Calibration improves accuracy when 5-in-1 sensor placement or environmental factors impact your data accuracy.
- Choose the weather category you wish to calibrate by pressing the ∧ or ∨ buttons until the category is displayed on the Selectable Category part of the display unit.
- Press AND HOLD the up and down arrow buttons and the button all at the same time for 15-20 seconds.• The display unit beeps, and all display data is hidden except for the value being calibrated.• “CAL” (calibrate) and arrows appear next to the value being calibrated.
- Press the up or down arrow buttons to calibrate the data value higher or lower from the actual reading.
- Press the button to confirm the calibration adjustment. Note: The “CAL” icon remains illuminated next to calibrated values.
Calibrate the Rain GaugeThe rain gauge on the 5-in-1 sensor can be calibrated to improve accuracy.Items Needed: 5-in-1 sensor, display unit, plastic cup, pin, screw driver
- First, ensure 5-in-1 sensor is perfectly level using built-in bubble level.
- Place display unit close so you can monitor it during calibration.
- Make a pin hole in the bottom of a plastic cup. Hold the cup over the rain gauge and fill it with exactly 1 cup (8oz.) of water, allowing the water to drip into the rain gauge. You should hear the internal buckets tip and see water drain through the rain gauge.
- A few seconds after each bucket tip, the display unit displays rainfall in approximately 0.01″ or more increments.
- The cup of water should take more than 10 minutes to empty; a quicker period will result in inaccurate calibration. Try to simulate a normal steady rainfall. When cup is empty of water, display unit should register 1.06″
Tips
- There should be nearly an equal number of water drops (about 25 water drops) between bucket tips. If not, adjust the calibration screws on the bottom of the 5-in-1 sensor until an equal number of water drops are tipping the buckets. Then, restart the calibration procedure.
- If you don’t hear the buckets tipping and see water dripping alternately out of each drain, there may be an issue with the rain gauge or it’s adjustment. See Troubleshooting on page 15.
AdjustmentIf the rain gauge doesn’t register close to 1.06″, make an EQUAL adjustment to the two calibration screws on the bottom of the 5-in-1 sensor. Turning screws clockwise increases rainfall; counter clockwise decreases rainfall.• To adjust the rainfall reading by 2% turn both screws 1/8 of a turn.• To adjust the rainfall reading by 4% turn both screws 1/4 of a turn.• To adjust the rainfall reading by 8% turn both screws 1/2 of a turn.
Watch the video at www.acurite.com/5in1
Specifications
| TEMPERATURE RANGE | Outdoor: -40ºF to 158ºF; -40ºC to 70ºC |
| Indoor: 32ºF to 122ºF; 0ºC to 50ºC | |
| HUMIDITY RANGE | Outdoor: 1% to 99% |
| Indoor: 16% to 98% | |
| WIND SPEED | 0 to 99 mph; 0 to 159 kph |
| WIND DIRECTION INDICATORS | 16 points |
| RAINFALL | 0 to 99.99 in; 0 to 99.99 cm |
| WIRELESS RANGE | 330ft / 100m depending on home construction materials |
| OPERATING FREQUENCY | 433mhz |
| POWER | Display: 3 x AA alkaline batteries |
| Sensor: 4 x AA alkaline or lithium batteries | |
| DATA REPORTING | Wind Speed: 18 seconds; Direction: 30 seconds |
| Outdoor temperature & humidity: 36 sec. updates | |
| Indoor temperature & humidity: 60 sec. updates |
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:1- This device may NOT cause harmful interference, and2- This device must accept any interference received, including interference that may cause undesired operation.WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions:(1) This device may not cause interference, and(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
Customer Support
AcuRite customer support is committed to providing you with best-in-class service. For assistance, please have the model number of this product available and contact us in any of the following ways:
(877) 221-1252[email protected]24/7 support at www.AcuRite.com
- Installation Videos
- Instruction Manuals
- Replacement Parts
- Register your Product
- Support User Forum
- Submit Feedback & Ideas
Limited One Year Warranty
At AcuRite, we proudly uphold our commitment to quality technology. Chaney Instrument Co. warrants that all products it manufactures to be of good material and workmanship, and to be free of defects when properly installed and operated for a period of one year from the date of purchase.
We recommend that you visit us at www.AcuRite.com for the fastest way to register your product. However, product registration does not eliminate the need to retain your original proof of purchase in order to obtain warranty benefits.
Chaney Instrument Co. warrants that all products it manufactures to be of good material and workmanship, and to be free of defects when properly installed and operated for a period of one year from the date of purchase. Remedy for breach of this warranty is limited to repair or replacement of the defective item(s). Any product which, under normal use and service, is proven to breach the warranty contained herein within ONE YEAR from date of sale will, upon examination by Chaney, and at its sole option, be repaired or replaced by Chaney. Transportation costs and charges for returned goods shall be paid for by the purchaser. Chaney hereby disclaims all responsibility for such transportation costs and charges. This warranty will not be breached, and Chaney will give no credit for products it manufactures which have received normal wear and tear, been damaged (including by acts of nature), tampered, abused, improperly installed, damaged in shipping, or repaired or altered by others than authorized representatives of Chaney.
The above-described warranty is expressly in lieu of all other warranties, express or implied, and all other warranties are hereby expressly disclaimed, including without limitation the implied warranty of merchantability and the implied warranty of fitness for a particular purpose. Chaney expressly disclaims all liability for special, consequential or incidental damages, whether arising in tort or by contract from any breach of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Chaney further disclaims all liability from personal injury relating to its products to the extent permitted by law. By acceptance of any of Chaney’s products, the purchaser assumes all liability for the consequences arising from their use or misuse. No person, firm or corporation is authorized to assume for Chaney any other liability in connection with the sale of its products. Furthermore, no person, firm or corporation is authorized to modify or waive the terms of this paragraph, and the preceding paragraph, unless done in writing and signed by a duly authorized agent of Chaney. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.For in-warranty claims:Chaney Instrument Co. | 965 Wells St. | Lake Geneva, WI 53147
It’s More than Accurate, it’s ACU ► RITE.AcuRite offers an extensive assortment of precision instruments, designed to provide you with information you can depend on to Plan your day with confidence™.www.AcuRite.com
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks andcopyrights are the property of their respective owners. AcuRite uses patented technology. Visit www.AcuRite.com/patents for details.
Printed in China0150A1 INST 012114
References
[xyz-ips snippet=”download-snippet”]