ACURITE Wireless Indoor/Outdoor Thermometer Instructions

ACURITE Wireless Indoor/Outdoor Thermometer Instructions

Battery InstallationBatteries not incudedInsert 2 fresh alkaline “AAA” batteries into the main unit first, then the remote unit next. Do not mix old and new batteries. Do not mix alkaline, standard (carbonzinc), or rechargeable (nickelcadmium) batteries.Slide off the battery compartment cover on the back of each unit. Be sure to insert the batteries in the correct manner according to the polarity symbols indicated in the battery compartment. After the batteries are installed in the main unit, “IN” will display the main unit temperature. The “OUT” temperature will display “” due to the remote unit not being powered on at this point.Once batteries are installed, the remote unit will transmit the wireless signal to the main unit about once every minute. If the temperature does not display under the “OUT” on the main unit after a few minutes, refer to the troubleshooting section of this manual.

Placement:The main unit may be wall mounted using the builtin hanger, or it can be placed on a desk or table using the foldout stand. The remote sensor can be wallmounted.The remote unit is weather resistant. Keep out of direct sunlight and direct weather elements to extend the life of the unit. Also, when selecting a location for the base unit, make sure it is within 100 feet of the wireless remote sensor. The range may be affected by electronic interference from devices such as televisions and computers. For the best results, keep both units at least 10 feet away from any electrical equipment or devices that may cause electronic interference.

Troubleshooting:If the main unit displays “” in the “OUT” display area for more than a few minutes:

  • The batteries may be low in the wireless remote sensor unit.
  • The wireless remote sensor unit may be out of range.
  • Electronic devices or equipment may be causing interference relocate both units.
  • Both units may need to be reset to reestablish wireless communications.

If this problem persists, remove and replace the batteries on both units and place both units in close proximity to each other for awhile. This may help reestablish communications and avoid any electronic interference in the area.

Specifications:

  • Temperature measurement range:
    • MAIN UNIT: 32ºF 122ºF
    • WIRELESS REMOTE: 0ºF 130ºF

Battery Compartment Access (back)

BATTERY SAFETY:Follow the polarity(+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard).DO NOT use rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    • Consult the dealer or an experienced radio/TV technician for help.

Do not return product to retail store. For Technical Assistance and product return information,please call Chaney Instrument Co. direct at:877-221-1252

LIMITED WARRANTY – INTERNATIONAL

Conswner may have more remedies at law than follows. Chaney Instrument Company warrants to the owner, this product to be free from defect in material and workmanship

for one year from date of purchase. CHANEY INSTRUM:ENT SHALL NOT BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES,

WHETHER ARISING IN CONTRACT OR TORT. Chaney Instrument’s obligation (at its option) is limited to repair or replace this product. For in-warranty repair, send

clock, accompanied by Guarantee, bearing Dealer’s name and date of purchase, with $5.00 to cover handling and postage, to:

www.chaneyinstrument.comTel: 877-221-1252 Made in ChinaChaney Instrument Company965 Wells Street Lake Geneva, Wisconsin 53147

References

[xyz-ips snippet=”download-snippet”]


Posted

in

by