Adtemp™ 415FLDigital Fever ThermometerInstructions for Use
ADC® Adtemp™ 415FL Digital Fever ThermometerThank you for choosing an ADC® Adtemp™ digital stick thermometer. Your new thermometer is designed to provide accurate measurements. Attempt thermometers to meet or exceed all relevant international performance standards.
Device Description and Intended UseThis device is intended to measure human body temperature in children and adults.It has a compact size and digital display and can be used in a professional or household environment.
Parts and Assembly:
Symbol DefinitionsThe following symbols are associated with your thermometer.
| Symbol | Definition |
| Important warning/caution | |
 |
Not made with natural rubber latex |
|
Phthalate-free |
|
Operating instructions |
|
Manufacturer’s information |
|
Authorized European representative’s information |
| 0197 |
Meets essential requirements of EuropeanMedical Device Directive 93/42/EEC |
|
Lot number |
 |
Multifunction button |
|
Auto-detection error |
| M | Memory indication |
|
Low battery indication |
General Warnings A warning statement in this manual identifies a condition or practice which, if not corrected or discontinued immediately, could lead to patient injury, illness, or death.
WARNING: This instrument is designed for oral, rectal, or axillary use only.
WARNING: High prolonged fever requires medical attention, especially for young children. Please contact your physician.
WARNING: Keep out of reach of unsupervised children. Components may be harmful if swallowed.
WARNING: Stop using the thermometer if it operates erratically or if the display malfunctions.
WARNING: Oral temperature readings are often 1.0°F to 2.0°F lower than actual body temperatures; rectal measurements are generally 1.0°F to 2.0°F higher.
WARNING: Avoid taking temperature for 30 minutes after physical exercise, bathing, dining, or drinking hot or cold beverages.
WARNING: Allow the thermometer to warm naturally to room temperature before using. Performance may be affected if operated or stored outside stated temperature and humidity ranges or if the patient’s temperature is below the ambient (room) temperature.
WARNING: After using, clean the thermometer and place it into the case.Clean the unit by wiping it with a dry cloth and disinfecting the probe with isopropyl (rubbing) alcohol. See cleaning instructions for additional details.
CAUTION: Keep thermometer away from direct sunlight, extreme temperatures, or dust.
CAUTION: Do not boil, bite, bend, drop, or disassemble the thermometer.
CAUTION: Do not open the unit except to replace the battery.
CAUTION: Do not use this device close to strong electromagnetic fields, such as mobile telephones.
CAUTION: Do not autoclave. Please note the cleaning procedures described in this manual.
CAUTION: Dispose of batteries in accordance with locally applicable regulations, not with domestic waste.
CAUTION: IP22: Protected against solid foreign objects of 12.5mm diameter and greater. Protected against vertically falling water drops when the device is tilted up to 15°.
How to Use
- Disinfect the probe with isopropyl (rubbing) alcohol before using.
- Press and release the multifunction button. The thermometer will beep and the display will read:
confirming the unit is functioning properly. The last reading will be displayed for approximately 2 seconds. Next, the thermometer will read “L°F” or “L°C”, depending on the current scale. - We recommend using probe covers with all digital stick thermometers. If using, place the cover over the tip of the unit.
- Place the probe in the appropriate position for your measurement site (see Ensuring Accurate Temperature Measurement below).
- The °F or °C symbol will flash when the unit is ready to measure temperature.Please note that the “ ” indicates a low battery. See instructions for replacing the battery before measuring temperature. Do not expect an accurate temperature reading if this low-battery indicator is present. An “Error” message in the window indicates your unit is not functioning properly.
- Depending on the measurement site, the unit will complete measurement in 18-20 (oral), 10 (rectal), or approximately 40 (axillary) seconds. The display will flash and the unit will beep signaling completion.
- Read and record the temperature and time for reference. The reading will automatically be stored in the memory.
- Use the multifunction button to turn the unit off. This will prolong the battery life. If you do not turn the unit off, it will shut down automatically in approximately 8 (±1) minutes.
Special FeaturesLast-Temperature Memory Recall: Press the multifunction button to activate the thermometer. The display 
will appear first and then display the last reading.If the last measurement didn’t finish and there is no temperature displayed, the last memory will display “L” with °F or °C flashing.
Switching Temperature ModesFrom the OFF position, the Celsius or Fahrenheit mode can be switched by pressing and holding the multifunction button for at least 5 seconds. After 3 seconds, the °F or °C will flash, indicating the thermometer is ready to measure.
Ensuring Accurate Temperature MeasurementWe recommend using probe covers with all digital stick thermometers. (Figure 1)
Oral Use: Place the probe well under the patient’s tongue (Figure 2). Keep the mouth closed while the thermometer is reading.
Instruct children not to bite down on the probe. The peak temperature should be reached in approximately 18-20 seconds. Opening the mouth or improper placement of the probe tip could result in a long time for reading.
Rectal Use: Lubricate the probe cover with a water-soluble jelly for easier insertion; do not use petroleum jelly, as it may cause an inaccurate reading. Gently insert the tip of the probe no more than 1/2 inch into the rectum. STOP if you meet any resistance.The sensing unit is on the very tip of the probe and there is no need to insert the probe deep into the rectum. A normal temperature by this method is usually considered between 1.0°F to 2.0°F (0.5°C to 1.0°C) HIGHER than an oral temperature. The peak temperature should be reached in approximately 10 seconds, and the unit will make a continuous beeping sound. Dispose of the used probe cover and wash the thermometer as recommended.
Axillary Use: Wipe armpit with a dry towel. Place the probe in the patient’s armpit (Figure 3) and keep the patient’s arm pressed firmly against the body. The peak temperature should be reached in approximately 40 seconds. Improper placement of the probe and closure of the arm against the body could result in a long time for reading.
- Battery ReplacementWhen the symbol “ ” appears in the lower right of the display, the battery needs to be replaced.
- Remove battery compartment lid (Figure 4).
- Use a pointed object such as a toothpick to pry loose the old battery. Avoid using any sharp metal object.
- Place new 1.5V coin-type battery (LR41 or equivalent). Ensure the battery is correctly positioned with the “+” facing up or towards the LCD screen.
- Replace the battery cover securely (Figure 4).
Cleaning and Disinfecting Do not use a corrosive detergent to clean the unit.
Clean and disinfect the thermometer before and after each use.
- The use of probe covers is recommended to help avoid spreading germs, and to keep the thermometer clean. The thermometer should be cleaned after use even when probe covers are used.
- Wipe probe with a clean cloth dipped in a disinfectant solution such as 70-75% isopropyl (rubbing) alcohol solution or soap and water.
- Rinse off disinfectant residue.
Care and Storage
- Do NOT drop or crush; this device is not shockproof.
- Do NOT dismantle or modify the device.
- Do NOT store the device in an extreme environment with direct sunlight or high/low temperatures, or in a location with high humidity or severe dust.
- Store the unit in the protective case while not in use.
Specification
| Accuracy: | 0.2°F/0.1°C between 93.2°F to 107.6°F(34.0°C to 42.0°C) a room temperature of 64.4°F to 82.4°F (18°C to 28°C)±0.4°F/0.2°C between 90.0°F to 93.2°F(32.0°C to 34°C) and 107.6°F to 109.9°F (42.0°C to 43.9°C) |
| Operating Conditions: | 50.0°F to 104.0°F (10.0°C to 40.0°C) |
| Storage Conditions: | -13°F to 131°F (-25°C to 55°C) |
| Relative Humidity: | 15-95% Non-Condensing |
| Measurement Mode: | Real measurement with the peak-hold method |
| Audible Alarm: | 1 beep at start-up.Continuous beep at measurement completion |
| Auto Turn Off: | In approximately 8 minutes |
| Memory Feature: | Stores last temperature reading |
| Expected Service Life: | 5 years |
| Standards: | Complies with EN 12470-3, ASTM E 1112-00,IEC 60601-1, IEC 60601-1-2, IEC 60601-1-11, ISO 80601-2-56Electromagnetic compatibility: device fulfills thestipulations of standard IEC 60601-1-2 |
**The manufacturer recommends a calibration check every 2 years.
Limited Warranty
ADC® warrants its products against defects in materials and workmanship under normal houshold use and service as follows:
- Warranty service extends to the original retail purchaser only and commences with the date of delivery.
- Your Attempt Digital Stick Thermometer is warranted for two years from the date of purchase.
What Is Covered: Replacement of parts, and labor.
What Is Not Covered: Transportation charges to ADC. Damages caused by abuse, misuse, accident, or negligence. Incidental, special, or consequential damages. Some states do not allow the exclusion or limitation of incidental, special, or consequential damages, so this limitation may not apply to you.
To Obtain Warranty Service: Send item(s) postage paid to ADC, Attn: Repair Dept., 55 Commerce Dr., Hauppauge, NY 11788. Please include your name and address, phone no., proof of purchase, and a brief note explaining the problem.
Implied Warranty: Any implied warranty shall be limited in duration to the terms of this warranty and in no case beyond the original selling price (except where prohibited by law). This warranty gives you specific legal rights and you may have other rights which vary from state to state.
For Australian Consumers: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Visit www.adctoday.com to view this instruction booklet in other languages.
On Electronic (Shenzhen) Co., Ltd.No. 497, Ta Laneg Nan Road,Ta Laneg Street Baoan District,Shenzhen, China Microlife AG Espenstrasse 139 9443 Widnau, Switzerland
Refer to the user manual before use
Batteries and electronic devices must be disposed of in accordance with the locally applicable regulations, not with domestic waste.
Type BF applied part
IB p/n 93-415FL-00 rev 3
Dist. by: ADC55 Commerce DriveHauppauge, NY 11788
Inspected in the U.S.A.Made in Chinatel: 631-273-9600toll-free: 1-800-232-2670fax: 631-273-9659email: [email protected]www.adctoday.com
report this ad
Printed in China
References
[xyz-ips snippet=”download-snippet”]