AEOTEC AEOEZWA007 Lasso Sensor for Water Sensor 6 User Manual

AeotecAeotec Lasso Sensor for Water Sensor 6SKU: AEOEZWA007

QuickstartThis is a Z-Wave Device. To run this device please connect it to your mains power supply.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.Z-Wave ensures reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified ZWave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise, it will automatically turn into a lower level of security to maintain backward compatibility.For more information about Z-Wave technology, devices, white papers, etc. please refer to www.z-wave.info.

Product Description

The Aeotec Lasso Sensor is an innovative sensor that has no equal.The product is connected to the Aeotec Water Sensor Dock (AEOEZW160) and detects even the smallest amounts of water over its entire length. The Aeotec Lasso Sensor is suitable to cover whole areas and not only single points. This allows you, for example, to secure your washing machine over a large area by moving the Lasso Sensor from the connection point to underneath the washing machine. This protects you from potential water damage over a wide area.Water damage can easily be avoided – with the Aeotec Water Sensor 6 (AEOEZW122), the Aeotec Water Sensor Dock (AEOEZW160), and the Aeotec Lasso Sensor.

Features:

  • Long sensor for the detection of very small quantities of liquid
  • Comprehensive detection possible
  • Can only be used in combination with the Aeotec Water Sensor Dock
  • Can be expanded several times and thus extended
  • Length: 1.45m

Prepare for Installation / Reset

Please read the user manual before installing the product.In order to include (add) a Z-Wave device to a network, it must be in the factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.manuals-backend.z-wave.info/make.php?lang=en&sku=AEOEZWA007&cert=

Safety Warning for Mains Powered DevicesATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default, the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick troubleshooting

Here are a few hints for network installation if things don’t work as expected.

  1. Make sure a device is in a factory reset state before including it. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise, you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Don’t poll FLIRS devices.
  6. Make sure to have enough mains powered devices to benefit from the meshing

Technical Data

Dimensions 0.0600000×0.0600000×0.0200000 mm
Weight 14 gr
EAN 8.10667E+11
Frequency XXfrequency
Maximum transmission power XXantenna

Explanation of Z-Wave specific terms

  • Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways, Remote Controls or battery-operated wall controllers.
  • Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators, and even remote controls.
  • Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
  • Inclusion — is the process of adding new Z-Wave devices into a network.
  • Exclusion — is the process of removing Z-Wave devices from the network.
  • Association — is a control relationship between a controlling device and a controlled device.
  • Wakeup Notification — is a special wireless message issued by a Z-Wave device to announce that is able to communicate.
  • Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.

(c) 2020 Z-Wave Europe GmbH, Antonstr. 3, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwave.eu. The template is maintained by Z-WaveEurope GmbH. The product content is maintained by Z-Wave Alliance, Certification Team, [email protected]. Last update of the product data: 06.11.2020

manuals-backend.z-wave.info/make.php?lang=en&sku=AEOEZWA007&cert=

References

[xyz-ips snippet=”download-snippet”]


Posted

in

by