August Active Noise Cancelling Bluetooth Headphones User Manual
MODEL: EP765
August International LtdUnited KingdomTel: +44 (0)845 250 0586www.augustint.com
Thank you for purchasing the August EP765 Bluetooth Wireless Stereo Headphones. This user manual is designed to familiarize you with all the features of this device. Please take the time to read this user manual carefully, even if you are already familiar with a similar product.
SafetyTo ensure the safety of you and others, please read the Safety Instructions before using this device. Please do not disassemble the EP765, it can be unsafe and will invalidate the manufacturer’s warranty.
DisposalPlease ensure the product and accessories are disposed ofin compliance with the WEEE (Waste Electrical and Electronic Equipment) Directive and any other regulations applicable to your country. Always check with the environment agency and any other relevant authorities for current disposal regulations.
Declaration of ConformityThe Declaration of Conformity can be found on our website at http://augustint.com/ en/declaration/
Customer ServiceYou can contact us by phone on: +44 (0)845 250 0586 or by email at: should you require further technical support or customer service.
1. Safety Instructions
Storage and Use
Maintenance
Please unplug all leads before cleaning this device.
2. Main Features
- 30dB Hybrid ANC Solution
- 4 Dedicated Microphones for Enhanced Noise Reduction
- Over-Ear Design for Optimum Comfort and Passive Noise Reduction
- Bluetooth v5.0 with up to 20H Battery Life
- App Compatible for Custom Audio Equalizing
3. Box Contents
4. Part Names and Functions
- Power But ton I Phone Call Control I Play I Pause
- Status LED
- Volume Up/Next
- Volume Down I Previous
- ANC LED
- ANC Switch
- Power Socket
- Microphone
- 3.5mmAudio Jack
5. Operation
5.1 Power
Please fully charge the EP765 before first use or if left unused for a long period of time.
To charge, use the power cable to connect the headphones to a powered USB port.
Whilst charging, the status LED lights red and turns blue once fully charged.
Ensure the output voltage from the USB port or the charger is 5V.Charging voltage greater than 5V may damage the headphones.
5.2 Switch On / OffPress the Power Button for 2 seconds to switch on the EP765. The EP765 will enter reconnection mode and status LED will flashes blue.
Press and hold the Power Button for 3 seconds to switch off the EP765.
5.3 Bluetooth ConnectionsThe EP765 will enter re connection mode after switching on and will connect to any previous known device automatically.
To pair to a new device, tum off the EP765 first then press an d hold the power button for 5 seconds to enter pairing mode. In pairing mode the status LED will flash red and blue alternately.
-For mobile phones and tablets
- Scan for available Bluetooth device on your mobile phone or tablets. (Please consult your device’s user manual if necessary)
- Select ‘EP765’ from the available devices and confirm the connection. Some devices require a pin code. If this is the case, please enter the code ‘()()()()’.
- Once successfully connected, the status LED will lights blue slowly.
-For computers
- Enable the Bluetooth function on your computer.
- Select ‘Device and Printers’ from the Control Panel and click ‘Add a Device’.
- Select ‘EP765’ from the available devices, the system will install the driver automatically. If a pin code is requested, please enter the code ‘0000’.
- Once successfully paired and connected, the status LED will lights blue slowly.
The EP765 could connect dual devices at the same time. After connecting the first device, press and hold the Power Button for 3 seconds to switchofftheEP765. Then press and.hold the power button for 5 seconds to enter pairing mode, and then connect second device with EP765.
5.4 Noise CancellingUse the ANC switch to turn on / off the noise cancelling. The ANC LED will light blue while ANC is enabled.
5.5 Audio – InTo use the EP765 as a pair of wired headphones, use a 3.5mm audio cable to connect the EP765 to your source device. Once the audio cable is connected to the EP765, the device switches to wired mode automatically.
5.6 Remote Control
6. Charging
Connect the EP765 to a powered USB port using the provided USB charging cable. While charging, the Status LED will light red and become blue once the battery is fully charged. A full charge takes approximatively 2 hours depending on power input
Note: Ensure the output voltage from the USB port or the charger is 5V. Charging voltage greater than 5V may damage the headphones.
7. Specification
8. Troubleshooting
9. Warranty
This product is guaranteed for twelve months from the date of the original purchase. In the unlikely event of any defect arising due to faulty materials or workmanship, the unit will be either replaced or repaired free of charge (where possible) during this period. An alternative product will be offered in case the product is no longer available or repairable.
This warranty is subject to the following conditions:
- The warranty is only valid within the country where the product is purchased.
- The product must be correctly installed and operated in accordance to the instructions given in this user manual.
- The product must be used solely for domestic purposes.
- The warranty only covers the main unit, and does not cover the accessories.
- The warranty does not cover the damage caused by misuse, negligence, accident and natural disaster.
- The warranty will be rendered invalid if the product is resold or has been damaged by inexpert repairs. The manufactures disclaim any liability for incidental or consequential damages.
- Please consult our customer adviser before returning any product; we are not responsible for any unexpected product returns.
- Any faulty product must be kept and returned in the original packaging with all the accessories and the original copy of the purchase receipt
The warranty is in addition to, and does not diminish, your statutory or legal rights.
Customer Service:Telephone: +44 (0) 845 250 0586Email:
This product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The Declaration of conformity may be consulted online athttp://www.augustint.com/en/declaration
Industry Canada StatementThis device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept interference, including interference that may cause undesired operation of the device.
Note: This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation.
This equipment generates uses andcan radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
No Unauthorized Modifications: Do not make any changes or modifications to this product without the prior express written approval of August International Ltd. Any changes or modifications made without express written approval could void the user’s authority to operate this product.
For details of further relevant technical standards, please contact us at the address above.
[xyz-ips snippet=”download-snippet”]