airlive PoE Injector User Manual
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of AirLive Technology Corp.AirLive Technology Corp has made the best effort to ensure the accuracy of the information in this user’s guide. However, we are not liable for the inaccuracies or errors in this guide. Please use with caution. All information is subject to change without noticeAll Trademarks are properties of their respective holders.
Disposal
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.
Overview
Ethernet 802.3at PoE Injector (PJ 1G 30W, PJ 2.5G 30W, PJ 5G 30W)
The AirLive PJ 1G/2.5G/5G 30W Gigabit Ethernet POE Injector is fully compatible with IEEE802.3af (15.4W) and IEEE802.3at (30W). The POE port supports a maximum output power of 30W, and the port supports 10/100/1000 (1G model), 2.5G (2.5G model) and 5G (5G) self adaption. It supports AC 100 240V voltage input; the working temperature range is 20°C ~ +50°C, seamless ultrasonic bonding, better protection effect. It takes the electricity from the power source and the data from the Ethernet network and then combines them into a signal that can be transmitted through the UTP/STP cable up to 100m.The product can be widely used in IP Camera, AP, 30W PoE PC Panel, AP, digital signage display system, PoE LED, etc. Its reliable hardware design can ensure your automation system runs without interruption and stability.
Gigabit Ethernet 802.3bt PoE Injector (PJ 1G 90W)
The AirLive PJ 1G 90W Gigabit Ethernet POE Injector is fully compatible with IEEE802.3af (15.4W) IEEE802.3at (30W) and IEEE802.3bt (90W). The POE port supports a maximum output power of 90W, and the port supports 10/100/1000 self adaption. It supports AC 100 240V voltage input; the working temperature range is 20°C ~ + 50°C, seamless ultrasonic bonding, better protection effect. It takes the electricity from the power source and the data from the Ethernet network and then combines them into a signal that can be transmitted through the UTP/STP cable up to 100m.The product can be widely used in PTZ high speed dome, PC Panel, compact computer, all in one computer, digital signage display system, PoE LED, etc. Its reliable hardware design can ensure your automation system runs without interruption and stability.
1.1 Connecting PJ 1G 30W, PJ 2.5G 30W, PJ 5G 30W
Power on the device by connecting the AC cable first. Connect a RJ 45 cable from a switch/router to the PoE Injector’s port called Data In, this is Data only. From the PoE Injector’s PoE Out port a RJ 45 cable can now be used to Power On and transfer Data for, for example a PoE Camera or Access Point. The PoE Out port has both Power and Data.
1.2 Connecting PJ-1G-90W
Power on the device by connecting the AC cable first. Connect a RJ 45 cable from a switch/router to the PoE Injector’s port called Data In, this is Data only. From the PoE Injector’s PoE Out port a RJ 45 cable can now be used to Power On and transfer Data for, for example a PoE Digtital Signage device or an Access Point. The PoE Out port has both Power and Data.
For more detailed specifications please see the datasheet. The datasheets can been found online on www.airlive.com** Specifications are subject to change and improvement without notice.
Read More About This Manual & Download PDF:
References
[xyz-ips snippet=”download-snippet”]