ANKER A2228 PowerDrive Speed 2 3.0 Quick Dual USB Car Charger User Guide

Table of Contents

ANKER A2228 PowerDrive Speed 2 3.0 Quick
 Dual USB Car Charger User Guide

Using Your PowerDrive

Plug it in
Charge your phones and tablets

For the fastest and safest charge, use an Anker® cable, your device’s original cable or a certified one (such as MFi).

Specifications

Attention

Avoid extreme temperaturesUse original or certified cablesDon’t expose to liquidsAvoid dropping Lassen Sie dasDon’t disassemble

Warning

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for car charger Model A2228.
Before using car charger, read all instructions and cautionary markings on car charger
Do not expose charger to rain, moisture, or snow.
Use of an attachment not recommended or sold by the car charger manufacturer may result in a risk of fire, electric shock, or injury to persons.
To reduce risk of damage to cigarette lighter connector and cord, pull by cigarette lighter connector rather than cord when disconnecting charger.
Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
Do not operate charger with damaged cord or cigarette lighter connector replace it immediately.
Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceperson.
Do not disassemble charger; take it to a qualified serviceperson when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
To reduce risk of electric shock, unplug charger before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.
To reduce the risk of fire or electric shock, do not interconnect output terminations
CAUTION – For continued protection against risk of fire, replace only with same type and ratings of fuse, fuse rating 32Vdc, 7A.

SAVE THESE INSTRUCTIONSFCC StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:(1) Reorient or relocate the receiving antenna.(2) Increase the separation between the equipment and receiver.(3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.(4) Consult the dealer or an experienced radio / TV technician for help.

The following importer is the responsible party. Company Name: Fantasia Trading LLC Address: 9155 Archibald Avenue, Suite 202, Rancho Cucamonga, CA, 91730, US Telephone: +1 (909) 484 1530

This device complies with Industry Canada license-ICES-003. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Declaration of ConformityHereby, Anker Innovations Limited declares that the product type A2228 is in compliance with Directive 2014/30/EU & 2011/65/EU & 2001/95/EC The full text of the EU declaration of conformity is available at the following internet address: https://www.anker.comAnker Innovations Limited | Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Anker Innovations Deutschland GmbH | Georg-Muche-Strasse 3, 80807 Munich, Germany Anker Technology (UK) Ltd | Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom

GB Declaration of ConformityHereby, Anker Innovations Limited declares that the product type A2228 is in compliance with following Directives: Electromagnetic Compatibility Regulations 2016, The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The full text of the GB declaration of conformity is available at the following internet address:https://www.anker.com