APOLLO Rechargeable Cordless Screwdriver Instruction Manual

4.8V Rechargeable Cordless ScrewdriverInstruction Manual

Welcome to the instruction manual for the APOLLO 4.8V Rechargeable Cordless Screwdriver. Please read all information below to ensure the safe operation of this product.

GENERAL SAFETY INSTRUCTIONS

Work Area

* Before beginning to use your Cordless Screwdriver, ensure that your work area is clean and well lit.* Be careful not to operate your Cordless Screwdriver in the presence of flammable liquids, gases or dust, as sparks may ignite.* Keep children away from the work area when using your Cordless Screwdriver.

Safety

* Before use, carefully check the tool to determine whether it will operate and perform its intended function.* Check for misalignment and freezing of moving parts, breakage of parts, damage to guards and switches and any other conditions that may affect its operation. Do not use the tool if any part is damaged or defective. Do not use the tool if the Forward/Reverse Switch does not work.* Have any damaged or defective parts replaced by our service center. Never attempt any repairs yourself.* Avoid unintentional turning on of this tool.* Do not carry the tool with a finger on the Forward/Reverse Switch or the On/Off Trigger.* Never carry the charger by its cord nor pull the cord to disconnect it from the socket.* Keep the cord away from heat, oil and sharp edges.* Store this screwdriver when not in use.* When not in use, tools, batteries and rechargers should be stored in a dry, locked or high place, out of reach of danger.* Maintain tools with care.* Keep handles and switches dry, clean and free from oil and grease.

IMPORTANT!

Before using this tool you must charge the battery. Charging the battery:* The battery needs to be charged before first use.* Only after several charges and discharge cycles will the battery attain and maintain full capacity.* The battery may become warm while charging, this is normal and does not indicate a problem.

  1. To charge the battery, insert the charger plug into the charging socket.
  2. Leave the tool connected to the charger for up to 5 hours. Before using the tool, unplug the charger and disconnect the tool from the charger.For your own safety read this manual carefully before using your Cordless Screwdriver.

Caution:* Do not charge using other specification chargers. Use only the APOLLO charger that came with this screwdriver when charging.* Do not use the tool while it is connected to the recharger.

Batteries

* Do not store in locations where the temperature may exceed 40ºC (104ºF).* Charge only at ambient temperatures between 4ºC (39.2ºF) and 40ºC (104ºF).* Charge only using the charger provided with the tool as other chargers might use different amperages and can damage or destroy your battery and/or screwdriver.* When disposing of batteries, follow the instructions provided in the “RBRC” section.* Under extreme conditions, battery leakage may occur. Avoid skin contact. In case of skin contact with battery liquid, immediately rinse with water. Neutralize with a mild acid such as lemon or vinegar.

4.8 V Cordless Screwdriver Parts

Fitting and removing a screwdriver bit

* Use only 1” or longer bits.* To fit a screwdriver bit, push it into the bit holder until secure.* To remove a screwdriver bit, pull it straight from the bit holder.

Automatic Spindle Lock Function

* The spindle lock allows you to use the tool as a regular manual screwdriver giving you the ability to more firmly tighten a screw or to loosen a very tight screw.

Operating your cordless screwdriver

* To tighten a screw, push forward the Forward/Reverse Switch and press the On/Off Trigger.* To loosen a screw, press back on the Forward/Reverse Switch and press the On/Off Trigger.* Always wait until the motor has come to a complete stop before changing the direction of rotation.

Cleaning And Maintenance

This Cordless Screwdriver does not require any special maintenance.

TECHNICAL DATA

Voltage__________4.8 VNo-load speed_____150 r/minTransformer_______ Input 120V AC 60 Hz, Output 6V DC, 0.3A with UL listingBit Holder_________1/4″ (6.35mm)Battery Type________ 4 x 1.2V Ni-Cd Rechargeable BatteriesCharger Current_____ 0.3ACharge time________4-5 Hours

RBRC SEAL

The RBRC (Rechargeable Battery Recycling Corporation) Seal on the nickel-cadmium battery is meant to indicate that APOLLO has covered the expense of the recycling cost at the end of the battery’s useful life. In some areas, it is illegal to dispose of these batteries in the trash so RBRC provides an environmentally friendly means of disposal. For information on how to dispose of these batteries, simply call 1-866-591-4749.

ONE YEAR WARRANTY

Limited WarrantyYour APOLLO Cordless Screwdriver is warranted against defects in workmanship and materials for one year from the date of original purchase. Please send in your warranty registration card ASAP to ensure that your warranty is actively registered and please keep your register receipt as proof of purchase.For questions or comments about this product, or to obtain replacement parts, please call 1-866-591-4749.Damage while in the possession of the consumer which does not result from a defect in materials and workmanship, and damage from other than normal use, including misuse, abuse, and repair by unauthorized parties is not covered by this limited warranty.

Limitations:Implied warranties are limited to one year from the date of purchase. All warranties other than the express warranty herein contained, including but not limited to, any implied warranty of merchantability or fitness for a particular purpose are limited in duration to the applicable warranty period set forth above.Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives specific legal rights and you may also have other rights that vary from state to state.Distributed By:Apollo Tools, Ltd. 255 Clapp Road – Suite 200Scituate, MA 02066USAVisit our website at: www.apollotools.comContact us at: [email protected]Or phone us at: 1-866-591-4749International Sales: [email protected]ls.comMade in China

References

[xyz-ips snippet=”download-snippet”]


Posted

in

by