Aqara E1 Hub Instruction Manual

Product Introduction

Hub E1 is a new hub launched by Aqara, which is USB-powered and supports Zigbee 3.0 protocol. With small size and flexible installation, it can be installed and applied on sockets and electrical appliances with a USB port in the home, and work with a  variety of accessories, which can be used as a Wi-Fi repeater for data forwarding.

Quick Setup

Connect to the Aqara Home app

1. Download the AppScan the following QR code or search for “Aqara Home” in the App Store to download and install the Aqara Home app.https://aiot-management.aqara.cn/config/app/aqaraHomeDeveloping
2. Set the hub.1. Plug the hub into a USB port that can provide power, wait for the yellow indicator to flash quickly, and make sure your mobile phone is connected to a Wi-Fi network in the 2.4 GHz frequency band.* Please keep the mobile phone as close to the hub as possible, and make sure that the mobile phone and the hub are using the same Wi-Fi network2. Open the Aqara Home app, click “+” in the upper right corner of the home page, select “Hub E1”, and follow theinstructions of the app to operate.* Connect to HomeKit: Please scan or manually input the HomeKit on the hub nameplate to set the code according to the prompts of the Apple “Home” app, and then follow the prompts to operate. Please properly protect the HomeKit on the nameplate to set the code.Once added successfully, the added hub can be viewed in the Apple “Home” app.3. If the addition fails, please long press the hub button for 10s to reset the network, and then add it again in the appPlease log in the following website to ask for help: www.aqara.com/support.
3. UsageAdd accessory: After the hub is added successfully, please refer to the manual of the accessory for adding.When an accessory is successfully added, the accessory that is HomeKit compatible will automatically sync to HomeKit,which can be viewed on the Apple “Home” app.This product can be used as a Wi-Fi repeater device with an open network hotspot. Please turn on the repeater function inthe app. It allows to modify the default SSID and password, supports a maximum of 4Mbps data forwarding capacity, andcan access two Wi-Fi devices at most, which is recommended to connect with only one subordinate Aqara product (such ascamera and hub).

Installation DescriptionHub E1 is a new hub launched by Aqara, which is USB-powered and supports Zigbee 3.0 protocol. With small size and flexible installation, it can be installed and applied on sockets and electrical appliances with a USB port in the home, and work with a  variety of accessories, which can be used as a Wi-Fi repeater for data forwarding.

1. In order to ensure stable communication between the hub and each accessory, the hub is recommended to be installed in the center of the area where the accessory is located.
2. If there is no shelter in the room, the communication distance between the hub and the accessory can be up to 30 meters.

Indicator Description

Specifications

NoticeCommunication between iPhone, iPad, Apple Watch, HomePod, or Mac and the HomeKit- enabled Hub E1 is secured byHomeKit technology.Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsiblefor the operation of this device or its compliance with safety and regulatory standards.Warnings

1. This product is NOT a toy. Please keep children away from this product.
2. This product is designed for indoor use only. Do NOT use in humid environments or outdoors.
3. Beware of moisture, do NOT spill water or other liquids onto the product.
4. Do NOT place this product near a heat source. Do NOT place it in an enclosure unless there is normal ventilation.
5. Do NOT attempt to repair this product by yourself. All repairs should be performed by an authorized professional.
6. This product is only suitable for improving the convenience of your home life and reminding you about the status of your devices. It should NOT be used as security equipment for homes, buildings, warehouses,s or any other places. If a user violates the product use instructions, the manufacturer will NOT be liable for any risks and property losses.

Under normal use of conditions, this equipment should be kept at a separation distance of at least 20cm between the antennaand the body of the user.

EU Declaration of ConformityHereby, Lumi United Technology Co., Ltd declares that the radio equipment type Hub E1, HE1-G01 is in compliance with  Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:  https://www.aqara.com/DoC/

UK Declaration of ConformityHereby, Lumi United Technology Co., Ltd declares that the radio equipment type Hub E1, HE1-G01 is in compliance with Directive 2017 (SI 2017 No. 1206, as amended by SI 2019 No. 696).The full text of the UK declaration of conformity is available at the following internet address: http://www.aqara.com/DoC/.

WEEE Disposal and Recycling InformationAll products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as the terms and conditions of such collection points.

FCC ID: 2AKIT-HE1G01

Federal Communications Commission (FCC) compliance statement:

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) this device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authorityto operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC: 22635-HE1G01IC NOTICE TO CANADIAN USERSThis device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and EconomicDevelopment Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

report this ad

This Class B digital apparatus complies with Canadian ICES‐003.

This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Manufacturer: Lumi United Technology Co., Ltd.Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District,Shenzhen, China.Online Customer Service: www.aqara.com/support Email: [email protected]

References

• 
  Home
• 
  Home