ASUS Wireless-AC1750 Dual Band Gigabit Router User Guide

RT-AC66U B1

Wireless-AC1750 Dual Band GigabitRouter

Quick Start Guide

WEU15297 / Revised Edition V6 / March 2019

WEU15065_RT-AC66U_B1_QSG_V5.indb 1           2019/3/5 14:59:32

Package contents

RT-AC66U B1                AC adapter RJ-45 cable                    Quick Start Guide Warranty card

NOTE: If any of the items is damaged or missing, contact your retailer.

 

A quick look

  1. USB 3.0 port
  2. LAN LED
  3. WAN LED
  4. 2.4GHz/5GHZ LED
  5. Power LED
  6. Power (DC-IN) port
  7. Power switch
  8. USB 2.0 port
  9. Reset button
  10. WAN port
  11. LAN ports
  12. WPS button

3

NOTES:

  • USB External HDD/Flash disk:

The wireless router works with most USB HDDs/Flash disks up to 2TB and supports read-write access for FAT16, FAT32, EXT2, EXT3, and NTFS.To safely remove the USB disk, launch the web GUI (http://router.asus.com), then in the Network Map page’s upper right corner, click the USB icon and click Eject USB 1.Incorrect removal of the USB disk may cause data corruption.For the list of file system and hard disk partitions that the wireless router supports, visit http://event.asus.com/networks/disksupport

4

Positioning your wireless router

For the best wireless signal transmission between the wireless router and the network devices connected to it, ensure that you:

  • Place the wireless router in a centralized area for a maximum wireless coverage for the network devices.
  • Keep the device away from metal obstructions and away from direct sunlight.
  • Keep the device away from 802.11g or 20MHz only Wi-Fi devices, 2.4GHz computer peripherals, Bluetooth devices, cordless phones, transformers, heavy-duty motors, fluorescent lights, microwave ovens, refrigerators, and other industrial equipment to prevent signal interference or loss.
  • To ensure the best wireless signal, orient the three detachable antennas as shown in the drawing below.
  • For optimum performance, adjust the internal cooling system. Refer to the user manual for details.
  • Always update to the latest firmware. Visit the ASUS website at http://www.asus.com to get the latest firmware updates.

5

Before you proceed
  1. Unplug and disconnect the wires/cables from your existing modem setup and release your computer’s outmoded IP address.

a: Unplug the AC adapter from the power outlet and disconnect it from your cable/ADSL modem.b: Disconnect the network cable from your cable/ADSL modem.c: Reboot your computer (recommended).

WARNING! Before disconnecting the wires/cables, ensure that your cable/ADSL modem has been turned off for at least two minutes. If your modem has a backup battery, remove it as well.

6

2. Set up your wireless environment.

a: Insert your wireless router’s AC adapter to the DC-IN port and plug it to a power outlet.b: Using the bundled network cable, connect your computer to your wireless router’s LAN port.

 

IMPORTANT! Ensure that the WAN and LAN LEDs are blinking.

c: Using another network cable, connect your modem to your wireless router’s WAN port.d: Insert your modem’s AC adapter to the DC-IN port and plug it to a power outlet.

3. Disable some settings on your computer.

A. Disable the proxy server, if enabled.B. Set the TCP/IP settings to automatically obtain an IP address.C. Disable the dial-up connection, if enabled.

NOTE: For more details on disabling your computer settings, refer to Frequently Asked Questions (FAQs).

7

Getting started
  1. Configure your wireless settings via the wireless router’s web graphics user interface (web GUI).

a: Launch your web browser such as Internet Explorer, Firefox, Google Chrome, or Safari.

    

a                                     b

NOTE: If QIS does not launch automatically, follow these steps to manually launch QIS: On your web browser, key in http://router.asus.com and run the Quick Internet Setup (QIS) Wizard again. Disable the proxy settings, dial-up connection, and set your TCP/IP settings to automatically obtain an IP address. For more details, refer to the FAQs section for auto-diagnosis.

8

b: The wireless router’s Quick Internet Setup (QIS) feature automatically detects if your ISP connection type is Dynamic IP, PPPoE, PPTP, L2TP, and Static IP. Key in the necessary information for your connection type.

NOTE: The auto-detection of your ISP connection type takes place when you configure the wireless router for the first time or when your wireless router is reset to its default settings.

IMPORTANT! Obtain the necessary information about your Internet connection type from your Internet Service Provider (ISP).

 

c: Assign the network name (SSID) and security key for your 2.4GHz and 5GHz wireless connection. Click Apply when done.d: Your Internet and wireless settings are displayed. Click Next to continue.e: Read the wireless network connection tutorial. When done, click Finish.

 

NOTE: You can assign a network name with up to 32 characters.

9

Frequently Asked Questions (FAQs)

After following the steps, I still cannot access the wireless router’s web graphics user interface (web GUI) to configure the wireless router settings.

A. Disable the proxy server, if enabled.Windows® 7

1. Click Start > Internet Explorer to launch the web browser.2. Click Tools > Internet options > Connections tab > LAN settings.

 

 

 

3. From the Local Area Network (LAN) Settings screen, untick Use a proxy server for your LAN.4. Click OK when done.

10

MAC OS

1. From your Safari browser, click Safari > Preferences > Advanced > Change Settings…2. From the Network screen, deselect FTP Proxy and Web Proxy (HTTP).3. Click Apply Now when done.

NOTE: Refer to your browser’s help feature for details on disabling the proxy server.

B. Set the TCP/IP settings to automatically obtain an IP address.

Windows® 71. Click Start > Control Panel > Network and Internet > Network and Sharing Center > Manage network connections.2. Select Internet Protocol Version 4 (TCP/IPv4), then click Properties.

11

3. To obtain the iPv4 IP settings automatically, tick Obtain an IP address automatically.4. Click OK when done.

 

 

 

 

MAC OS

1. Click the Apple icon located on the top left of your screen.2. Click System Preferences > Network > Configure…3. From the TCP/IP tab, select Using DHCP in the Configure IPv4 dropdown list.4. Click Apply Now when done.

NOTE: Refer to your operating system’s help and support feature for details on configuring your computer’s TCP/IP settings.

12

C. Disable the dial-up connection, if enabled.

Windows® 71. Click Start > Internet Explorer to launch the browser.2. Click Tools > Internet options > Connections tab.3. Tick Never dial a connection.4. Click OK when done.

 

NOTE: Refer to your browser’s help feature for details on disabling the dial-up connection settings.

D. Close all running web browsers.

The client cannot establish a wireless connection with the router.

Out of Range:

  • Put the router closer to the wireless client.
  • Try to change the channel settings.

Authentication:

  • Use wired connection to connect to the router.
  • Check the wireless security settings.
  • Press the Reset button at the rear panel for more than five seconds.

13

Cannot find the router:

  • Press the Reset button at the rear panel for more than five seconds.
  • Check the setting in the wireless adapter such as SSID and encryption settings.

Cannot access the Internet via wireless LAN adapter.

  • Move the router closer to the wireless client.
  • Check whether the wireless adapter is connected to the correct wireless router.
  • Check whether the wireless channel in use conforms to the channels available in your country/area.
  • Check the encryption settings.
  • Check if the ADSL or Cable connection is correct.
  • Retry using another Ethernet cable.

If the ADSL “LINK” light blinks continuously or stays off, Internet access is not possible – the Router is unable to establish a connection with the ADSL network.

  • Ensure that all your cables are all properly connected.
  • Disconnect the power cord from the ADSL or cable modem, wait a few minutes, then reconnect the cord.
  • If the ADSL light continues to blink or stays OFF, contact your ADSL service provider.

Network name or encryption keys are forgotten.

  • Try setting up the wired connection and configuring the wireless encryption again.
  • Press the Reset button of the wireless router for more than five seconds.
  • Factory default settings:
User name / Password:

admin / admin

IP address:

http://router.asus.com

SSID:

Check the rating label on the back side of your router

14

Where can I find more information about the wireless router?

15

ASUS Recycling/Takeback ServicesASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling information in different regions.

REACHComplying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm

Federal Communications Commission StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • This device may not cause harmful interference.
  • This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

159

Prohibition of Co-locationThis device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

IMPORTANT NOTE:Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirement, please follow operation instruction as documented in this manual.

WARNING! This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Compliance Statement of Innovation, Science and Economic Development Canada (ISED)

This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

CAN ICES-3(B)/NMB-3(B)

Radio Frequency (RF) Exposure Information

The radiated output power of the ASUS Wireless Device is below the Innovation, Science and Economic Development Canada radio frequency exposure limits. The ASUS Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator any part of your body.

This device has been certified for use in Canada. Status of the listing in the Innovation, Science and Economic Development Canada’s REL (Radio Equipment List) can be found at the following web address:http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html

Additional Canadian information on RF exposure also can be found at the following web:https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

160

Manufacturer ASUSTeK Computer Inc.Tel: +886-2-2894-3447Address: 4F, No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWAN
Authorised representative in Europe ASUS Computer GmbHAddress: HARKORT STR. 21-23, 40880 RATINGEN, GERMANY
Authorised distributors in Turkey BOGAZICI BILGISAYAR TICARET VE SANAYI A.S.Tel./FAX No.: +90 212 331 10 00 / +90 212 332 28 90Address: ESENTEPE MAH. BUYUKDERE CAD. ERCAN HAN B BLOK NO.121 SISLI, ISTANBUL 34394
CIZGI Elektronik San. Tic. Ltd. Sti.Tel./FAX No.: +90 212 356 70 70 / +90 212 356 70 69Address: GURSEL MAH. AKMAN SK.47B 1 KAGITHANE/ISTANBUL
KOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC. A.S.Tel. No.: +90 216 5288888Address: EMEK MAH.ORDU CAD. NO:18, SARIGAZi, SANCAKTEPE ISTANBUL
ENDEKS BİLİŞİM SAN VE DIŞ TİC LTD ŞTİTel./FAX No.: +90 216 523 35 70 / +90 216 523 35 71Address: NECIP FAZIL BULVARI, KEYAP CARSI SITESI, G1 BLOK, NO:115 Y.DUDULLU, UMRANIYE, ISTANBUL
PENTA TEKNOLOJI URUNLERI DAGITIM TICARET A.STel./FAX No.: +90 216 528 0000Address:ORGANIZE SANAYI BOLGESI NATO YOLU 4.CADDE NO:1 UMRANIYE, ISTANBUL 34775

163

Networks Global Hotline Information
Region Country/ Area Hotline Number Service Hours
Europe Cyprus 800-92491 09:00-13:00 ; 14:00-18:00 Mon-Fri
France 0033-170949400 09:00-18:00 Mon-Fri
Germany 0049-1805010920

0049-1805010923

(component support)

0049-2102959911 (Fax)

09:00-18:00 Mon-Fri

10:00-17:00 Mon-Fri

Hungary 0036-15054561 09:00-17:30 Mon-Fri
Italy 199-400089 09:00-13:00 ; 14:00-18:00 Mon-Fri
Greece 00800-44142044 09:00-13:00 ; 14:00-18:00 Mon-Fri
Austria 0043-820240513 09:00-18:00 Mon-Fri
Netherlands/ Luxembourg 0031-591570290 09:00-17:00 Mon-Fri
Belgium 0032-78150231 09:00-17:00 Mon-Fri
Norway 0047-2316-2682 09:00-18:00 Mon-Fri
Sweden 0046-858769407 09:00-18:00 Mon-Fri
Finland 00358-969379690 10:00-19:00 Mon-Fri
Denmark 0045-38322943 09:00-18:00 Mon-Fri
Poland 0048-225718040 08:30-17:30 Mon-Fri
Spain 0034-902889688 09:00-18:00 Mon-Fri
Portugal 00351-707500310 09:00-18:00 Mon-Fri
Slovak Republic 00421-232162621 08:00-17:00 Mon-Fri
Czech Republic 00420-596766888 08:00-17:00 Mon-Fri
Switzerland-German 0041-848111010 09:00-18:00 Mon-Fri
Switzerland-French 0041-848111014 09:00-18:00 Mon-Fri
Switzerland-Italian 0041-848111012 09:00-18:00 Mon-Fri
United Kingdom 0044-1442265548 09:00-17:00 Mon-Fri
Ireland 0035-31890719918 09:00-17:00 Mon-Fri
Russia and CIS 008-800-100-ASUS 09:00-18:00 Mon-Fri
Ukraine 0038-0445457727 09:00-18:00 Mon-Fri

164

Region Country/ Area Hotline Number Service Hours
Asia-Pacific Australia 1300-278788 09:00-18:00 Mon-Fri
New Zealand 0800-278788 09:00-18:00 Mon-Fri
Japan 0800-1232787 09:00-18:00 Mon-Fri 09:00-17:00 Sat-Sun
0081-570783886 ( Non-Toll Free ) 09:00-18:00 Mon-Fri 09:00-17:00 Sat-Sun
Korea 0082-215666868 09:30-17:00 Mon-Fri
Thailand 0066-24011717

1800-8525201

09:00-18:00 Mon-Fri
Singapore 0065-64157917 11:00-19:00 Mon-Fri
0065-67203835

( Repair Status Only )

11:00-19:00 Mon-Fri

11:00-13:00 Sat

Malaysia 1300-88-3495 9:00-18:00 Mon-Fri
Philippine 1800-18550163 09:00-18:00 Mon-Fri
India

India(WL/NW)

1800-2090365 09:00-18:00 Mon-Sat

09:00-21:00 Mon-Sun

Indonesia 0062-2129495000 09:30-17:00 Mon-Fri
500128 (Local Only) 9:30 – 12:00 Sat
Vietnam 1900-555581 08:00-12:00

13:30-17:30 Mon-Sat

Hong Kong 00852-35824770 10:00-19:00 Mon-Sat
Taiwan 0800-093-456;

02-81439000

9:00-12:00 Mon-Fri; 13:30-18:00 Mon-Fri
Americas USA

Canada

1-812-282-2787 8:30-12:00 EST Mon-Fri

9:00-18:00 EST Sat-Sun

Mexico 001-8008367847 08:00-20:00 CST Mon-Fri

08:00-15:00 CST Sat

Brazil 4003 0988 (Capital) 0800 880 0988 (demais localidades) 9:00am-18:00 Mon-Fri

165

Region Country/ Area Hotline Number Service Hours
Middle East + Africa Egypt 800-2787349 09:00-18:00 Sun-Thu
Saudi Arabia 800-1212787 09:00-18:00 Sat-Wed
UAE 00971-42958941 09:00-18:00 Sun-Thu
Turkey 0090-2165243000 09:00-18:00 Mon-Fri
South Africa 0861-278772 08:00-17:00 Mon-Fri
Israel *6557/00972-39142800

*9770/00972-35598555

08:00-17:00 Sun-Thu

08:30-17:30 Sun-Thu

Balkan Countries Romania 0040-213301786 09:00-18:30 Mon-Fri
Bosnia

Herzegovina

00387-33773163 09:00-17:00 Mon-Fri
Bulgaria 00359-70014411

00359-29889170

09:30-18:30 Mon-Fri

09:30-18:00 Mon-Fri

Croatia 00385-16401111 09:00-17:00 Mon-Fri
Montenegro 00382-20608251 09:00-17:00 Mon-Fr
Serbia 00381-112070677 09:00-17:00 Mon-Fr
Slovenia 00368-59045400

00368-59045401

08:00-16:00 Mon-Fr
Baltic Countries Estonia 00372-6671796 09:00-18:00 Mon-Fri
Latvia 00371-67408838 09:00-18:00 Mon-Fri
Lithuania-Kaunas 00370-37329000 09:00-18:00 Mon-Fri
Lithuania-Vilnius 00370-522101160 09:00-18:00 Mon-Fri

NOTES:• UK support e-mail: [email protected]• For more information, visit the ASUS support site at: https://www.asus.com/support/

166

CE statement

Simplified EU Declaration of ConformityASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of EU declaration of conformity is available at https://www.asus.com/Networking/RT-AC66U-B1/HelpDesk_Declaration/.Declaration of Conformity for Ecodesign directive 2009/125/ECTesting for eco-design requirements according to (EC) No 1275/2008 and (EU) No 801/2013 has been conducted. When the device is in Networked Standby Mode, its I/O and network interface are in sleep mode and may not work properly. To wake up the device, press the Wi-Fi on/off, LED on/off, reset, or WPS button.This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.All operational modes:2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40)5GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80)The frequency, mode and the maximum transmitted power in EU are listed below:2400-2483.5MHz (802.11ac VHT40 NCS0/Nss1): 19.81 dBm5150-5250MHz (802.11ac VHT80 NCS0/Nss1): 22.07 dBm5250-5350MHz (802.11ac VHT80 NCS0/Nss1): 22.1 dBm5470-5725MHz (802.11ac VHT40 NCS0/Nss1): 29.21 dBmThe device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.The adapter shall be installed near the equipment and shall be easily accessible.

AT BE BG CZ DK EE FR
DE IS IE IT EL ES CY
LV LI LT LU HU MT NL
NO PL PT RO SI SK TR
FI SE CH UK HR UA
Safety Notices
  • Use this product in environments with ambient temperatures between 0°C(32°F) and 40°C(104°F).
  • Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating.
  • DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been damaged.
  • DO NOT place or drop objects on top and do not shove any foreign objects into the product.
  • DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms.
  • DO NOT cover the vents on the product to prevent the system from getting overheated.
  • DO NOT use damaged power cords, accessories, or other peripherals.
  • If the Adapter is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
  • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.

167

References

[xyz-ips snippet=”download-snippet”]


Posted

in

by