Product Manual
FB3200 / FB46001.330.274.8317www.ATLANTICWATERGARDENS.com
Introduction
Thank you for purchasing the Atlantic FB3200/FB4600 Fountain Basin. Before using this basin please take a moment to review this manual. Fountain Basins provide a stable, self-contained base to mount a pump and plumbing for decorative water features.
Installation
Begin by excavating a hole at least 6 inches larger than the basin and 12½” deep. This depth will leave the Fountain Basin slightly higher than the ground around it, which will keep soil, mulch, or gravel from washing in. Angling the sides of the hole outward slightly will aid in the backfill process
Caution: Do not dig too deep. The Fountain Basin should be set on undisturbed earth if possible. In case you over-dig, be sure to compact the soil thoroughly to prevent settling. The bottom of the hole should be level side-to-side and front-to-back (Figure 1)
Figura 1
Add enough water to the Fountain Basin to keep it from shifting during the backfill process. Use loose soil from the excavation to fill the void around the perimeter of the basin, leaving the area outside the pump chamber open until all of the electrical and plumbing connections are made. Lightly compact the soil around the basin as you backfill (Figure 2).
Caution: Over compacting can distort the sidewalls of the Fountain Basin.
Figura 2
Plumbing
Note: Auto Fill Kit AF1000 can be added to any Fountain Basin to keep the basin filled with water automatically. It is easiest to install AF1000 before plumbing the pump. Using a 7/8” bit, drill a hole about 1” below the top of the flat wall on the left side of the pump chamber (Figure 3). Connect the Autofill to your choice of water source using either the 3/4” Garden Hose Adapter, 1/2” rigid PVC slip fitting, or 1/2” flexible tubing adapter (all included in AF1000 Auto Fill Kit). See Kit Instructions for details.
Figura 3
Atlantic Pro-Series Fountain Basins have been designed to work in conjunction with Atlantic FBKIT1/FBKIT3 and TidalWave TT-Series and MD-Series pumps to simplify installation. FBKIT1 contains a single valve, 3/4” fittings, and tubing needed to connect one fountain piece. FBKIT3 contains 11/2” pump discharge fittings, Triton 3-way manifold, 3/4” fittings, and tubing needed to connect up to three fountain pieces.
Determine the layout of the fountain pieces, and the length of the ¾” tubing. The tubing runs on top of the Fountain Basin within the plumbing channels (Figure 4).
Figura 4
Note: The top deck of Atlantic Pro-Series Fountain basins is supported by 3 (FB3200) or 7 (FB4600) support cones. When installing large, heavy fountain pieces, it is recommended to distribute the weight evenly over multiple cones to reduce point loads.
A standpipe set just below the level of the water overflowing a decorative pot or vase will create an attractive bubbling effect. Set the decorative piece over the fitting, then attach a piece of ¾” Sch40 PVC to the fitting. Cut the standpipe to just below the water surface. Seal any gaps between the standpipe and the hole in the base of the piece with Atlantic SPSEAL Standpipe Sealant. To center and stabilize the standpipe, place a few rocks around the pipe to stabilize it (Figure 5). Fill the Basin with water, connect the pump to a GFI-protected outlet and adjust the flow as desired.
Figura 5
Decoration
To complete the installation, cover the Fountain Basin with gravel, polished stones, glass beads, or other decorative material. To disguise the outline of the Basin further, extend the material past the edge of the Basin. To enhance nighttime enjoyment of the fountain, complement your Fountain Basin with Atlantic’s LED lighting.
Installation of a Fountain Basin in Paver Patio or Walkway
The FB4600 and FB3200 Fountain Basin can be installed within a paver patio or walkway. Recessed pockets allow 1½” conduit sleeves to be installed within the radius of the basin. These sleeves allow access to the pump cords and low voltage wiring when surrounding the basin with hardscape materials. When setting the Fountain Basin within a paver patio, the top rim of the basin should be set at least 1” lower than the top of the pavers. This will help retain the decorative material after it is installed (Figure 6).
Figura 6
Warranty
This product carries a lifetime warranty. This warranty is extended solely to the original purchaser commencing from the date of the original purchase receipt. A misused or abused product voids this warranty.
Warranty ClaimsIn case of warranty claims, the complete Basin should be returned to the place of purchase accompanied by an original receipt.
1.330.274.8317www.ATLANTICWATERGARDENS.com
References
[xyz-ips snippet=”download-snippet”]