audio-technica AE3000 Cardioid Condenser Instrument Microphone User Manual

Table of Contents

audio-technica AE3000 Cardioid Condenser Instrument Microphone User Manual

Thank you for purchasing this product. Before using the product, read through the user manual to ensure that you will use the product correctly.Please keep this manual for future reference.

Features

Excels in high-SPL applications such as guitar cabinets, toms, snare, timpani and overheads
Large-diaphragm capsule combines with the open architecture of the headcase to provide an extremely accurate and open sound
Low-profile side-address design with tapered grille allows optimal positioning of element vis-à-vis sound source
Robust design for enduring dependability on the road
Integral 80 Hz HPF switch and 10 dB pad
Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source

Notes on use

The AE3000 is intended for use in professional applications where remote power is available.It requires 11V to 52V DC phantom power, which may be provided by a mixer or console, or by a separate, in-line source such as the Audio-Technica AT8801 single channel or CP8506 four-channel phantom power supplies.

Output from the microphone’s XLRM-type connector is low impedance (Lo Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” – positive acoustic pressure produces positive voltage at Pin 2.

An integral 80 Hz hi-pass filter provides easy switching from a flat frequency response to a low-end roll-off. The roll-off position reduces the microphone’s sensitivity to popping in close vocal use. It also reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically-coupled vibrations.

The AE3000 includes an AT8471 isolation clamp to provide secure mounting, versatile positioning, and effective dampening of unwanted mechanical noise.

Avoid leaving the microphone in the open sun or in areas where temperatures exceed 43°C for extended periods. Extremely high humidity should also be avoided.

Safety precaution

Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product.

Cautions for the product

Do not subject the product to strong impact to avoid malfunction.
Do not disassemble, modify or attempt to repair the product.
Do not handle the product with wet hands to avoid electric shock or injury.
Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty place.

Connection procedure

Connect the output terminals of the microphone to a device that has a microphone input (balanced input) compatible with a phantom power supply. The output connector is an XLRM-type with polarity as shown in the figure below.

This product requires 48 V DC phantom power.

Specifications

Element: Fixed-charge back plate, permanently polarized condenser
Polar pattern: Cardioid
Frequency response: 20 – 20,000 Hz
Low Frequency response: 80 Hz, 12 dB/octave
Open circuit sensitivity: -43 dB (7.0 mV) re 1V at 1 Pa
Impedance: 100 ohms
Maximum input sound level: 148 dB SPL, 1 kHz at 1% T.H.D.158 dB SPL, with 10 dB pad (normal)
Noise: 11 dB SPL
Dynamic range (typical): 137 dB, 1 kHz at Max SPL
Signal-to-noise ratio: 83 dB, 1 kHz at 1 Pa
Phantom power requirements: 11-52 V DC, 3 mA typicaol
Switch: High-pass filter, 10 dB pad (normal)
Weight (less accessories): 170 g
Dimensions: 115.5 mm long, 48.0 mm maximun diameter
Output conbnector: Integral 3-pin XLRM-type
Included accessories: AT8471 isolation clamp for 5/8″-27 threaded stands; 5/8″-27 to 3/8″-16 threaded adapter; soft protective pouch