Avilo H564i Wireless Bicycle Computer User Manual

Wireless Bicycle Computer

Thank you for purchasing the Wireless Bicycle Computer. We hope you will be satisfied with your purchase. Note: A slight rattle sound in the product is normal. It is part of the design of wireless automatic functions.What’s includedI * ComputerI * Sensor Transmitter1* Pad bracket4 * Cable tiesI* CR2032 batteryI • Magnet I Rubber band1 * Instruction sheet

Note:When attaching the sensor transmitter, battery cover, and computer mounting holder, do not tear off the shim especially the shim on the back of the computer battery cover. It is a part of the product and should not be torn off.

Installation

Computer Battery InstallationRemove the battery cover from the bottom of the computer by using a flat blade screwdriver, install one CR2032 battery with the positive (+) pole facing the battery cover and replace the cover. Should the LCD show irregular figures, take out the battery and reinstall it. ‘2060’ appears on the screen means installation correctly.

Sensor Transmitter Battery InstallationRemove the battery cover from the bottom of the computer by using a flat blade screwdriver, install one 2032 battery with the positive (+) pole facing the battery cover and replace the cover. Should the LCD show irregular figures, take out the battery and re-install it.Sensor Transmitter  Installation

Attach the sensor transmitter to the left fork blade, the distance between the computer and the sensor can not exceed 60cm, the closer the better. Using the shims to adjust the diameter, and using the cable ties(shown above) to tie it with the fork(once diameter, please tear off the yellow paper on the tape for fixing). Position the sensor transmitter and magnet as shows, make sure that the arc of the magnet intersects the alignment mark on the sensor transmitter with 1mm clearance.

Mounting Ring InstaiiationsAttach the mounting ring with the cable ties to the handlebar, adjust the mounting Ring on the handlebar with the shims to hold its position.

Computer InstallationAttach the computer to the mounting shoe by sliding the unit until it snaps firmly into its position. To remove it, press the button on it in the opposite direction.To check for proper speed function and sensor alignment, spin the front wheel with a computer in speed mode. Adjust the position of the sensor and magnet when there is no or weak reaction.

Setting of Parameters

Once you have set the wheel size parameter to ‘km/h or m/h, the rest of the parameters will change automatically while your tire is running.If you need to re-set the settings once the computer is working, press both rights and left buttons at the same time for at least 5 seconds. The “2060” code should appear and then you can re-set the wheel size. After this is done you can then set up km/h or m/h.

Wheel Size Input`2060′ appears on the screen when the battery has been installed, with one figure flashing, choose the correct wheel circumference from the table below. Press the RIGHT button to advance digits as needed and the LEFT button to confirm and advance. (The circumference ranges Omm-9999nun), press the LEFT button to enter KM/M mode.

TIRE SIZE CIR TIRE SIZE CIR TIRE SIZE CIR
29″x2.3″ 2326 27″x 1(630) 2145 24″x 1(520)” 1753
29″x2.2″ 2298 650c x 38Amm 2125 24″x 2.125″ 1965
29″x2.I” 2288 650c x 38Bmm 2105 24″x 2.00″ 1925
700c x 47mm 2268 650c x 25Cmm 1952 24″ x 1.9″ 1910
700c x 45mm 2242 650c x 23mm 1944 24″x 1.75″ 1890
700c x 44mm 2235 650c x 20mm 1938 22″x 1-1/2″ 1785
700c x 42mm 2224 650cTubulari 1920 22″x 1-3/8″ 1770
700c x 40mm 2200 26″x 1-1/2″ 2100 20″ x 1-3/8″ 1615
700c x 38mm 2180 26″x 1-3/8″ 2068 20″ x 1-1/8″ 1545
700cTubulari 2130 26″x 1-1/8″ 1970 20″ x 1.95″ 1565
700c x 35mm 2168 26″x 3.00″ 2170 20″x 1.35″ 1460
700c x 32mm 2155 26″x 2.35″ 2083 20″ x 1.25″ 1450
700c x 30mm 2146 26″ x 2.25″ 2070 18″ x 1.75″ 1350
700c x 28mm 2136 26″ x 2.10″ 2068 18″ x 1.50″ 1340
700c x 25mm 2105 26″ x 2.0″ 2062 17″ x 1-1/4″ 1340
700c x 23mm 2096 26″ x 1.95″ 2050 16″ x 1-3/8″ 1300
700c x 20mm 2086 26″ x 1.90″ 2045 16″ x 1-1/8 1290
700c x 19mm 2080 26″x 1.75″ 2023 16″ x 2.0″ 1245
700c x 18mm 2070 26″x 1.50″ 2010 16″ x 1.95″ 1240
27.5″x 2.25″ 2182 26″x 140″ 2005 16″ x 1.75″ 1195
27.5″x 2.1″ 2148 26″x 1.25″ 1950 16″ x 1.50″ 1185
27.5″x 1.50″ 2079 26″x 1.0″ 1913 14″ x 1.75″ 1055
27″x 1-3/8″ 2169 24″x 1-1/4″ 1905 14″ x 1.50″ 1020
27″x 1-1/4″ 2161 24″x 1-1/8″ 1795 12″ x 1.95″ 940
27″x 1-1/8″ 2155 24″x3/4″ 1785 12″x 1.75″ 935

Setting ( km/h ) / ( m/h )Press the RIGHT button to choose km/h or m/h. Press the LEFT button to enter CLOCK mode.CLK Mode(12H/24H)In CLOCK Mode, press the LEFT button for 3 seconds to enter 12/24H selection. Re-press the LEFT button for 12/24 exchanging. Press the RIGHT button to enter Hour setting mode, when the figure indicating HOUR start to flash, press the LEFT button to adjust it. Continue to press the RIGHT button to enter Minute setting mode, when the figure indicating MINUTE start to flash, press the LEFT button to adjust it and the RIGHT button to confirm, press the RIGHT button again to ODO mode. Setting the Last Valu of OdometerIn ODO mode, press the LEFT button for 2 seconds to set the ODO value, its initial value is 0000.0. when one figure flashing, press the RIGHT button to adjust it and the LEFT button to confirm it and start to set the next figure. (After the battery has been re-installed, the latest value can be inputted according to the value before pre-installation of the battery. )Reset of Mlileatie ParameterIn ODO mode, press and hold both RIGHT and LEFT buttons simultaneously for 3 seconds to clear the tire circumference and (km/m) setting, The user needs to reset the tire circumference and (km/m), the original ODO value, and CLOCK will remain unaffected.SpeedometerSpeed is shown all the time on the screen, its maximum reading is 99.9km/h(m/h), and it’s accurate to +/- 0.1km/h (in/h)•Speed ComputerDuring riding, ‘ + ‘ and ‘ -‘ indicates the current speed is higher or lower than the average speed(AVS).

OdometerIn ODO mode, the total distance is -. I indicated on the screen, its mileage range is 0.001 — 99999km(m). the _ •  display will be back to 0 when the value exceeds its maximum limit, press the RIGHT button to enter DST mode..Trip Distance (DST)In DST mode, the distance for one trip is indicated on the bottom line. DST ranges from 0.001 –9999km(m), when the value exceeds the range limit, it -restarts from 0 automatically. Both the time and the distance records will be cleared when the time of one trip exceeds the range limits.Press the LEFT button for 5 seconds to clear the records of DST, MXS, AVS, and TM.Press the RIGHT button to enter MXS mode.Maximum S wed (MXS)In MXS mode, maximum speed is indicated on the bottom line. Press the LEFT button for 5 seconds to clear the records of MXS, DST, AVS, and TM. Press the RIGHT button to enter AVS mode.Average SpeedIn AVS mode, the average speed is indicated on the bottom line. Press the LEFT button for 5 seconds to clear the records of AVS, DST, MXS, and TM. Press the RIGHT button to enter TM mode.Trip TimeIn TM mode, trip time is indicated on the bottom line.TM ranges 0 :00 :00 99 :59 :59. It will be back to 0 when the value exceeds the limits.Press the LEFT button for 5 seconds to clear the records of TM, DST, MXS, and AVS. Press the RIGHT button to enter SCAN mode.SCANIn Scan mode, DST, MXS, AVS, and TM • mode are indicated in tum every 4 seconds. Press the RIGHT button to enter CLOCK Mode.Sleep ModeIf no signal has been inputted for 300 seconds, the computer will enter into Sleep Mode, and the CLK value remains. It will turn back to the former model with all the data collected when any signal is inputted or any button is pressed.FREEZE FRAME MEMORYPress the LEFT button at any time will enter into freeze-frame memory mode. Flashing TM data will appear on the screen. Press the RIGHT button to view the records of DST, MXS, AVS, and TM. Press the LEFT button to end it.

Button Instruction

Press the RIGHT button to choose any mode below: ODO, DST, MXS, AVS, TM, SCAN (DST. MXS, AVS. TM), and CLOCK. It’s unnecessary to press the LEFT button except to choose the Freeze frame Memory mode. In Freeze Frame Memory mode, press the RIGHT button, several data will display, re-press the LEFT button to turn back to other modes.

Malfunctions and Problems

Malfunctions Problems
No speedometer Improper magnet/sensor alignment Distance between computer and sensor transmitter exceed 60cmThe low battery voltage of the sensor transmitter or computer.
A short distance of the transmitter or no receiving Lower battery voltage, need to change for a new one.
Display Abnormal figures Too much Electromagnetic interference around
An inaccurate value is indicated Improper input, such as wheel circumference.
Slow display response Temperature exceeds operating limits(Ot —55 C).
Black display Temperature too high, or put in direct sunlight for too long time. Need to take back to shadow place for a period.
Weak display Poor battery contact or dead battery
The display shows irregular figures Take out the battery and re-install it after 10 seconds.
Sensor without reaction Put off the insulation film of the sensor transmitter

Back LightThe backlight is only on when you press any button from 6 pm to 7 am.

Product Code: J192101Made in China for S&S Enterprises Ltd. 26 Perivale Park Middlesex UB6 7RL

[xyz-ips snippet=”download-snippet”]


Posted

in

by