User’s Manual
Bain Marie Art 90010
1. STRUCTURE NAME
STRUCTURE
2. POINTS FOR ATTENTION
2.1 POINTS FOR SPECIAL ATTENTION
2.2 SAFETY DEVICE
THE TEMPERATURE LIMITING CONTROL (MAX 105。C ) CAN SAFE GUARD THE ”THERMOS TANK” FOR SUITABLE TEMPERATURE. IT WILL BE AVOIDED THE ACCIDENTS IN CAUSE FOR THE TOO HIGH TEMPERATURE. (EG. : TOO HIGH TEMPERATURE MAKE THE ”THERMOS TANK” DRY. THE WATER HAS NOT BEEN FILLED TO THE EMPTY THERMOS TANK.)
2.3 CLOSE THE ELECTRICITY SWITCH AFTER USE.
AFTER USE, THE CONTROL THERMOSTAT MUST BE AGAINSTED THE CLOCKWISE TO TURN OFF IN CLOSING POSITION. THEN THE PLUG MUST BE PULLED OUT AND THE ELECTRICITY SUPPLY MUST BE CUT OFF.
3 OPERATION INSTRUCTION
3.1 PLACE THE ”BAIN MARIE”.
THE BAIN MARIES SHOULD BE PLACED ON A HORISONTAL PLANE. THE CONTROL THERMOSTAT OF THE BAIN MARIES SHOULD BE AGAINST THE CLOCKWISE TO TURN OFF IN CLOSING POSITION.
3.2 FILL EMPTY ”THERMOS TANK” TO THE WATER-LEVEL LINE
THE WATER-LEVEL LINE OF THE BAIN MARIES HAS TO DO WITH THE HEIGHT OF THE PAN. THE PAN SHOULD BE 25MM ABOVE THE WATER-LEVEL.
3.3 PUT THE FOOD INTO THE PAN THAN YOU PUT THE PAN INTO THE”THERMOS TANK”.
3.4 OPEN THE ELECTRICITY SWITCH AND ROTATE THERMOSTAT KNOB TO THE REQUIRED TEMPERATURE.
WHEN THE ELECTRICITY SUPPLY WIRE IS PLUGGED IN THE SPECIAL SOCKET OF 220V, THE POWER LIGHT SHOULD BE GOT LIGHT. TO GO CLOCKWISE AND ADJUST THE “CONTROL THERMOSTAT”, THEN THE TEMPERATURE LIGHT WILL BE GOT LIGHT.
DROP IN THE TEMPERATURE: AGAINST CLOCKWISE TO ADJUST THE “CONTROL THERMOSTAT”. RAISE THE TEMPERATURE: GO CLOCKWISE TO ADJUST THE “CONTROL THERMOSTAT”.
3.5 THE END OF CONCLUDING OPERATION
THE”CONTROL THERMOSTAT” MUST BE AGAINST CLOCKWISE TO TURN OFF IN CLOSING POSITION. PULL OUT THE PLUG, CUT OFF THE ELECTRICITY SUPPLY. POUR THE WATER FROM “THERMOS TANK” (HIGH TEMPERATURE! DO NOT TOUCH THE “THERMOS TANK” DIRECTLY.)
THE ”THERMOS TANK” SHOULD BE CLEARED AND DRIED WITH A WET COTTON CLOTH FOR USING AGAIN. (HIGH TEMPERATURE! DO NOT TOUCH THE “THERMOS TANK” DIRECTLY.)
4. ROUTINE INSPECTION
THE “BAIN MARIES” SHOULD BE CHECKED IN FRONT AND BEHIND OF COOPERATION. IN FRONT OF USING: CHECK THE CONTROL SYSTEM WHETHER IT DAMAGE. CHECK THE ELECTRICITY SUPPLY WIRE WHETHER IT AGE, SPLIT OR DAMAGE.
DURING THE USING: CHECK THE “BAIN MARIES” WHETHER IT BEGINS TO PECULIAR SMELL, BAD SMELL OR VIBRATION VOICE.
5. TROUBLESHOOTING GUIDE
THE ABOVE MENTIONED TERMS ARE MADE FOR REFERENCE ONLY. WHEN THERE ARE ABNORMAL PHENOMENA FOR THE “BAIN MARIES” OR THE SAFETY CONTROL DISCONNECTED, IT IS SAID THAT THERE ARE SOME PROBLEMS IN THE WIRING. IT MUST BE STOPPED TO USE AT ONCE.ADVICE THE AUTHORIZED SERVICE TECHNICIAN TO CHECK AND REPAIR IT AS SOON AS POSSIBLE.
6. SPECIFICATIONS
7. INSTALLATION INSTRUCTION
7.1 THE POINTS FOR INSPECTION BEFORE INSTALLATION.
THE PLACE SHOULD BE SMOOTH AND STEADY. AVOID THE FALL AND LEAK OF GAS. DO NOT STORE OR USE ANY FLAMMABLE VAPOURS OR LIQUIDS IN VICINITY OF”BAIN MARIES”. THE LIMIT FOR AMBIENT TEMPERATURE: FROM 0℃ TO 35℃ AMBIENT HUMIDITY: MAX 80 %
CHECK THE ACCESSORIES OF ”BAIN MARIES” WHETHER THEY ARE COMPLETED. CHECK THE OUTWARD WHETHER IT IS DAMAGED.
7.2 CONNECTED THE ELECTRICITY SUPPLY.
BEFORE THE USE: THE AIR VALVE (10A MIN), LEAKAGE OF ELECTRICITY SWITCH, FUSE AND SOCKET MUST BE INSTALLED.
THE ”GROUND WIRE”, SOCKET AND JUNCTION ,UST BE CONNECTED IN GOOD ORDER. CHECK THEY WHETHER THEY ARE LOOSED.
8. CIRCUIT DIAGRAM
9. DIAGRAM AND SPARE PARTS
Spare part list for 90010
Bain Marie Art 90010 User’s Manual – Bain Marie Art 90010 User’s Manual –
Questions about your Manual? Post in the comments!
[xyz-ips snippet=”download-snippet”]