Quick Start Guide112 DUAL VCOLegendary Analog Dual VCOModule for Eurorack
Controls
- PW MOD IN – Accepts a voltage from another module to control the pulse width.
- VCO OUT – Send the VCO signal to one or two sources via 3.5 mm TS cables.
- WAVEFORM – Select pulse, triangle or sawtooth waveforms for the VCO.
- PULSE WIDTH – Adjusts the pulse width modulation based on the voltage received at the PW MOD IN jack.
- MOD MANUAL – Sets the ratio between the upper and lower portions of the pulse wave.
- SYNC OUT – Sends a synchronization signal via 3.5 mm TS cable.
- RANGE – Sets the pitch range of the VCO in octave steps.
- SYNC IN – Accepts a synchronization signal via 3.5 mm TS cable.
- WEAK/STRONG – Determines the accuracy of synchronization.
- PITCH – Fine-tunes the pitch.
- MOD LEVEL – Adjusts the level of the signal connected to the associated MOD IN jack.
- MOD IN – Accepts voltages that control or modulate the VCO pitch.
Power Connection
Installation
The necessary screws are included with the module for mounting in a Eurorack case. Connect the power cable before mounting. Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track that allows individual threaded plates to slide along the length of the case. The free-moving threaded plates allow precise positioning of the module, but each plate should be positioned in the approximate relation to the mounting holes in your module before attaching the screws.Hold the module against the Eurorack rails so that each of the mounting holes are aligned with a threaded rail or threaded plate. Attach the screws partway to start, which will allow small adjustments to the positioning while you get them all aligned. After the final position has been established, tighten the screws down.
Specifications
| Pulse Width Input | |
| Type | 2 x 3.5 mm TS jacks, DC-coupled |
| Impedance | 70 kO, unbalanced |
| Maximum input level | ±10 V1 4% per volt |
| VCO Output | |
| Type | 4 x 3.5 mm TS jacks, DC-coupled |
| Impedance | 1 ko, unbalanced |
| Maximum output level | 10 V P-P |
| Frequency range with no external CV | 10 Hz to 500 Hz |
| Frequency range using external CV | 1 Hz to 30 kHz |
| Sync Input | |
| Type | 2 x 3.5 mm TS jacks, DC-coupled |
| Impedance | 100 ko, unbalanced |
| Maximum input level | 10 V P-P |
| Minimum input to trigger | 2.5 V P-P |
| Sync Output | |
| Type | 2 x 3.5 mm TS jacks, DC-coupled |
| Impedance | 1 kO, unbalanced |
| Maximum output level | 10 V P-P |
| Control Inputs | |
| Type | 6 x 3.5 mm TS jacks,summed |
| Impedance | 50 kΩ, unbalanced |
| CV range | ±10 V, 1 V/oct |
| Controls | |
| PW level | -∞ to unity gain |
| PW manual | 50% to min |
| Waveform | Triangle, sawtooth, pulse |
| Range | 32′, 16′, 8′, 4′, 2′ |
| Pitch | ±1 octive |
| Weak/strong | Sync mode select |
| Mod level | -∞ to unity gain |
| Power | |
| Power supply | Eurorack |
| Current draw | 90 mA (+12 V),
70 mA (-12 V) |
| Physical | |
| Dimensions | 81 x 129 x 46 mm
report this ad (3.2 x 5.1 x 1.8″) |
| Rack units | 16 HP |
| Weight | 0.2 kg (0.44 lbs) |
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly on or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021All rights reserved.
LIMITED WARRANTYFor the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
[xyz-ips snippet=”download-snippet”]