Quick Start Guide
EUROLIVEF1220DBi-Amped 250-Watt Monitor Speaker System with12″ Woofer, 3″ Tweeter and Feedback Filter
Important Safety Instructions
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN
Terminals marked with this symbol carry an electrical current of sufficient magnitude to constitute a risk of electric shock. Use only high-quality professional speaker cables with ¼” TS or twist-locking plugs pre-installed. All other installation or modifications should be performed only by qualified personnel.
This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.
CautionTo reduce the risk of electric shock, do not remove the top cover (or the rear section).No user-serviceable parts inside. Refer servicing to qualified personnel.
CautionTo reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.
CautionThese service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Use only attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
- Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
- Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service.
- Do not install in a confined space, such as a bookcase or similar unit.
- Do not place naked flame sources, such as light candles, on the apparatus.
- Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed of at a battery collection point.
- This apparatus may be used in tropical and moderate climates up to 45°C.
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly on or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances, and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
LIMITED WARRANTYFor the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
EUROLIVE F1220D Hook-up
Step 1: Hook-Up
EUROLIVE F1220D Hook-up
Step 1: Hook-Up
EUROLIVE F1220D Controls
Step 2: Controls
- MIC LEVEL knob controls the input level for the MIC IN input. (9) MIC IN input accepts balanced signals from devices using an XLR connector, such as microphones.
- POWER LED lights up when the loudspeaker is put into operation. (10) LINE IN input accepts balanced line-level signals using an XLR connector, such as mixer outputs or instrument signals converted through a DI box.
- CLIP LED lights up when signal distortion occurs. Reduce the volume with the LEVEL controls (MIC or LINE knobs) until the CLIP LED does not light up anymore, or occasionally lights up at signal peaks.
- LINE LEVEL knob controls the input level for the LINE IN input. (11) MIX OUT output connects directly to the inputs of the F1220D and carries the input signal with no processing applied. In this way, you can route the signal to the input of another device (for example,a second F1220D).
- EQ KNOBS boosts or cuts the low, middle, or high frequencies by 15 dB. (12) POWER SWITCH turns the power to the unit on and off.
- FEEDBACK FILTER FREQ Control adjusts the center frequency of the feedback filter.
- FEEDBACK FILTER LED lights up to indicate the feedback filter function has been activated.
- POWER SOURCE jack accepts the included IEC power cable. To avoid ground-loop hum,loudspeakers and mixing consoles should be connected to the same power circuit. FEEDBACK FILTER switch turns on the feedback filter.
Specifications
Amplifier
| Maximum output power | 250 W* |
| Configuration | Bi-amping |
| Type | Class-D |
| Overload protection | Dual-controlled limiter |
| Crossover type | Active |
| Crossover frequency | 2 kHz |
Audio Inputs
| Mic input | XLR connector, balanced |
| Sensitivity | -18 dBu to -37 dBu (Level VR from center to max.) |
| Impedance | 1 kΩ balanced, 2 kΩ unbalanced |
| Line input | XLR connector, balanced |
| Sensitivity | +16 dBu to -4 dBu (Level VR from center to max.) |
| Impedance | 10 kΩ balanced, 20 kΩ unbalanced |
Audio Outputs
| Mix output | XLR |
| Impedance | 100 Ω, unbalanced |
| Max. output | +22 dBu |
Equalizer
| High | ±15 dB @ 12 kHz |
| Mid | ±15 dB @ 2.5 kHz |
| Low | ±15 dB @ 80 Hz |
Feedback Filter
| Filter frequency | 350 Hz to 6 kHz |
| Level reduction | 15 dB |
| Q factor | 20 |
Loudspeaker System
| Type | 12″ woofer3″ Tweeter |
| Frequency range | 45 Hz to 18 kHz |
Indicators
| Power | Amber LED |
| Clip | Red LED |
| Feedback filter | Yellow LED |
Physical
| Enclosure | Trapezoidal, wood |
| Grille | Perforated steel |
| Mounting | Dual-angle 30 mm pole mount socket |
| Power consumption @ 1/8 max power | 35 W |
| Mains connection | Standard IEC receptacle |
Power Supply / Voltage
| Switch-mode power supply | 100-240 V~ 50/60 Hz, switchable |
| Power consumption @ 1/8 max power | 35 W |
| Mains connection | Standard IEC receptacle |
Dimensions/Weight
| Dimensions (H x W x D) | 238 x 500 x 354 mm (9.4 x 19.7 x 11.9″) |
| Weight | 10.7 kg (23.6 lbs) |
Other important information
- Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.
- Malfunction. Should your Music Tribe Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfiller for your country listed under “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.
- Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
EUROLIVE F1220D
Responsible Party Name: Music Tribe Commercial NV Inc.Address: 5270 Procyon Street, Las Vegas NV 89118, United States.Phone Number: +1 702 800 8290
EUROLIVE F1220DThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Important information:Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive 2014/35/EU, Directive 2014/30/EU, Directive 2011/65/EU, and Amendment 2015/863/ EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive1907/2006/EC.Full text of EU DoC is available at https://community.musictribe.com/EU Representative: Music Tribe Brands DK A/SAddress: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark
We Hear You
[xyz-ips snippet=”download-snippet”]