BenQ Adjusting the screen resolution User Manual

BenQ Adjusting the screen resolution User Manual

Adjusting the screen resolution

Due to the nature of liquid crystal display (LCD) technology, the picture resolution is always fixed. For the best display performance, please set the display to its maximum resolution that is the same with the monitor aspect ratio. This is called “Native Resolution” or maximal resolution ­ that is, the clearest picture. Please refer to the table below for the native resolution of your LCD. Lower resolutions are displayed on a full screen through an interpolation circuit. Image blurring across pixel boundaries can occur with the interpolated resolution depending upon the image type and its initial resolution.

  • To take full advantage of LCD technology you should select the native resolution setting of your PC screen as described below. Be aware that not all PC video cards provide this resolution value. If yours doesn’t, check with the video card manufacturer’s website for an updated driver for your particular model PC video card which supports this resolution. Software video drivers are often updated and available for new hardware video resolutions. If necessary, you may need to replace and update the PC video card hardware to be able to support the native resolution of the monitor.
  • Depending on the operating system on your PC, different procedures should be followed to adjust the screen resolution. Refer to the help document of your operating system for details.
  1. Open Display Properties and select the Settings tab. You can open Display Properties by right-clicking on the Windows desktop and selecting Properties from the pop-up menu.
  2. Use the slider in the Screen area section to adjust the screen resolution. Select the recommended resolution (maximum resolution) then click Apply. If you select some other resolution, be aware that this other resolution is interpolated and may not accurately display the screen image as well as it could do at the native resolution setting.
  3. Click OK then Yes.
  4. Close the DisplayProperties window.If your input source does not provide an image which is the same with the monitor aspect ratio, the displayed image may appear stretched or distorted. To maintain the original aspect ratio, image scaling options can be found in the Display Mode adjustment. See the user manual for more information.

Adjusting the screen refresh rate

You don’t have to choose the highest possible refresh rate on an LCD display, because it is not technically possible for an LCD display to flicker. The best results are obtained by using the factory modes already set in your computer. Check next chapter to see the factory modes: Preset display models on page 3.

Depending on the operating system on your PC, different procedures should be followed to adjust the screen resolution. Refer to the help document of your operating system for details.

  1. Double click the Display icon in Control Panel.
  2. From the Display Properties window, select the Settings tab and click the Advanced button.
  3. Select the Adapter tab, and select an appropriate refresh rate to match one of the applicable factory modes as listed in the specification table.
  4. Click Change, OK, then Yes.
  5. Close the Display Properties window.Adjusting the screen refresh rate 2

Preset display models

Timing support

PC / Video signal support

Input port

Resolution

Frame frequency (Hz) DisplayPort (V1.4) HDMI 2.0 USB-C™
PC timing Video timing PC timing Video timing PC timing

Video timing

640×480

60 v v v v v v
640×480 75 v   v   v

720×400

70 v   v   v  
720×480 60   v   v  

v

720×576

50   v   v   v
800×600 60 v   v   v

800×600

75 v   v   v  
832×624 75 v   v   v

1024×768

60 v   v   v  
1024×768 75 v   v   v

1152×870

75 v   v   v  
1280×720 50   v   v  

v

1280×720

60 v v v v v v
1280×800 60 v   v   v

1280×1024

60 v   v   v  
1280×1024 75 v   v   v

1680×1050

60 v   v   v  
1600×900 60 v   v   v

1920×1080

24   v   v   v
1920×1080 25   v   v  

v

1920×1080

30   v   v   v
1920×1080 50   v   v  

v

1920×1080

60 v v v v v v
1920×1080 100 v v v v v

v

1920×1080

120 v v v v v v
1920×1080 144   v   v  

v

2560×1080

60   v   v   v
2560×1080 100   v   v  

v

2560×1080

120   v   v   v
2560×1440 60 v   v   v

2560×1440

100            
2560×1440 120       v(*)  

2560×1440

144   v      

v

  • To make sure the above timing works, check the compatibility and specifications of your graphic card first.
  • To obtain the best image quality, refer to the above table to set the timing and the resolution of the input source.
  • (*): Available for game consoles that support 120hz. If your monitor is not supported, contact your local customer service for further assistance.

WQHD (2560×1440) video input

120 Hz 10-bit

Color space

YCbCr 4:2:2

Max. bit

8 bit 10 bit
Frame frequency 24, 25, 30 50, 60 100 120 144 24, 25, 30 50, 60 100 120

144

HDMI

v v v v   v (*) v (*) v (*) v (*)  
DisplayPort v v v v   v (*) v (*) v (*) v (*)
USB-C™

(DP Alt mode)

v v v v   v (*) v (*) v (*) v (*)

Color space

YCbCr 4:4:4 / RGB 4:4:4

Max. bit

8 bit 10 bit
Frame frequency 24, 25, 30 50, 60 100 120 144 24, 25, 30 50, 60 100 120

144

HDMI

v v v v   v (*) v (*) v (*)    
DisplayPort v v v v   v (*) v (*) v (*) v (*)
USB-C™

(DP Alt mode)

v v v v   v (*) v (*) v (*) v (*)

Color space

YCbCr 4:2:0

Max. bit

8 bit 10 bit
Frame frequency 24, 25, 30 50, 60 100 120 144 24, 25, 30 50, 60 100 120

144

HDMI

v v v v   v (*) v (*) v (*) v (*) v (*)
DisplayPort v v v v   v (*) v (*) v (*) v (*)

v (*)

USB-C™

(DP Alt mode)

v v v v   v (*) v (*) v (*) v (*)

v (*)

Color space YCbCr 4:2:0
Max. bit 12 bit
Framefrequency 24, 25, 30 50, 60 100 120 144
HDMI v (*) v (*) v (*) v (*)
DisplayPort v (*) v (*) v (*) v (*)
USB_CTM(DP Alt mode) v (*) v (*) v (*) v (*)

The monitor receives 10-bit or 12-bit data and displays 8-bit colors.

144 Hz 8-bit

Color space

YCbCr 4:2:2
Max. bit

8 bit

Frame frequency

24, 25, 30 50, 60 100 120 144
HDMI v v v v

v

DisplayPort

v v v v v
USB-C™

report this ad

(DP Alt mode)

v v v v

v

 

[xyz-ips snippet=”download-snippet”]


Posted

in

by