Bissell 1547 Series Hard Floor Expert Multi Cyclonic User Guide

HARD FLOOR EXPERT™ MULTICYCLONIC USER GUIDE

1547 SERIES

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM. 

Always connect to a polarized outlet (one slot is wider than the other). Unplug from outlet when not in use and before conducting maintenance. When using an electrical appliance, basic precautions should be observed, including the following:

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

  • Always connect to a polarized outlet (one slot is wider than the other). Do not modify the polarized plug to fit a non-polarized outlet or extension cord.
  • Do not leave vacuum cleaner when it is plugged in. Unplug from outlet when not in use and before servicing.
  • Do not use outdoors or on wet surfaces.
  • Do not allow to be used as a toy. Close attention is necessary when used by or near children.
  • Do not use for any purpose other than described in this User’s Guide. Use only manufacturer’s recommended attachments.
  • Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
  • Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
  • Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
  • Do not handle plug or vacuum cleaner with wet hands.
  • Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
  • Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
  • Turn off all controls before plugging or unplugging vacuum cleaner.
  • Use extra care when cleaning on stairs.
  • Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
  • Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.
  • Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
  • Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
  • Do not use without filters in place.
  • Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
  • Use only on dry, indoor surfaces.
  • Keep appliance on a level surface.
  • Do not carry the vacuum cleaner while it is running.
  • Unplug before connecting or disconnecting the TurboBrush® Tool.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

This model is for household use only.

THIS APPLIANCE HAS A POLARIZED PLUG

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way.

Product View

  1. Handle
  2. Extension Wand
  3. Hose
  4. Carry Handle
  5. Dirt Cup Release Button
  6. Emptying Button
  7. Cyclone
  8. Easy Empty™ Dirt Cup
  9. Hose Connector
  10. Turbine Hard Floor Tool
  11. Multi-Surface Floor Nozzle
  12. Crevice Tool, Dusting Brush & Upholstery Tool w/Holster

WARNING

Plastic film can be dangerous. To avoid danger of suffocation, keep away from babies and children.

WARNING

Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures.

WARNING

To reduce the risk of electric shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks.

Assembly

WARNING

Do not operate vacuum with damp or wet filters or without all filters in place first.

  1. Connect hose to vacuum by inserting hose connector on the end of the hose into the suction inlet. Make sure the hose is positioned so the tabs on the hose connector line up with the notches on the suction inlet.
  2. Connect hose handle to the end of the extention wand and twist slightly to tighten.
  3. Connect floor nozzle to the end of the extension wand and twist slightly to tighten.
  4. Once assembled, you can store your vacuum by inserting the storage clip (located on the back of the floor nozzle) into the storage slot on the rear of the vacuum.

Operations

Automatic cord rewind

Your vacuum is equipped with an automatic cord rewind. When cleaning is finished, press the power button OFF and grasp the plug to disconnect from the electrical outlet. Hold the plug and press the automatic cord rewind button to rewind the cord automatically

Power button

Turn the power ON or OFF by pressing lightly downward on the power button ( ).

Special tools

Your BISSELL vacuum is not only a powerful carpet and rug vacuum cleaner, it’s also a versatile bare floor and above floor vacuum cleaner when you select one of the special tools.

Floor nozzle

Use to vacuum carpets, rugs and bare floors. Swivel head turns to get into tight spaces and fits under cabinets.

  1. To vacuum carpets and rugs, push the brush switch to the carpet position . This will pull the brushes up into the floor nozzle.
  2. To vacuum bare floors, push the brush switch to the bare floor position . This will extend the brushes down from the floor nozzle.

Operations

Small accessoriesUse the crevice tool in tight, narrow spaces. Use the dusting brush to clean curtains, draperies, and side tables and window ledges. Use upholstery tool for soft furnishings.

Turbine Hard Floor ToolUse to vacuum to vacuum, tile, wood, laminate and other hard surfaces

Maintenance & Care

WARNING

To reduce the risk of electric shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks.

Empty the dirt cup

Empty the dirt cup as soon as the dirt reaches the “FULL” lines on the sides of the dirt cup.

  1. Unplug the vacuum from the electrical outlet.
  2. Press the dirt cup release button on the carry handle and lift up to remove the dirt cup.
  3. Choose an emptying method. Method #2 is recommended for allergy suffers.Method #1 – Hold the dirt cup over a rubbish bin and push the emptying button to open the bottom. Close the bottom after the dirt empties.Method #2 – Place a plastic bag over the bottom of the dirt cup. Push the emptying button through the plastic to open the bottom. After the dust settles, close the bottom and remove the bag to discard.
  4. Replace the dirt cup by placing it back into the vacuum and pushing down on the carry handle until it snaps back into place.

Cleaning the dirt cup filter

Use only BISSELL replacement filters in your vacuum.

  1. Unplug the vacuum from the electrical outlet.
  2. The dirt cup filters can be reached by removing the dirt cup from the vacuum, and unclipping the dirt cup lid then pivoting backwards. Pull filter upwards to remove.
  3. The dirt cup filter can be can be hand washed in cold water with a mild detergent. Rinse well and air dry thoroughly before placing back onto the filter frame base.
  4. Close dirt cup lid and replace dirt container back onto product.

Replacing the post-motor filter

The post-motor filter assists in the filtration process to return cleaner air to the room. Use only BISSELL replacement filters.

  1. Unplug the vacuum from electrical outlet.
  2. Remove the filter door (located in the wheel next to the on/ off switch of the vacuum) by twisting it anti-clockwise and pulling out and away from the vacuum
  3. The post-motor filter can be hand washed in cold water with a mild detergent. Rinse well and air dry thoroughly before placing back into the vacuum.
  4. Replace the filter door by aligning the tabs up with the slots on inside the wheel and turning clockwise until you feel a click.

Cleaning the cyclone shroud

  1. Remove the dirt cup from the dirt cup lid and cyclone assembly by twisting it anti-clockwise and pulling away.
  2. Remove the cyclone shroud by twisting it clockwise then pulling down and away from the dirt tank lid, over the secondary cyclone fine dirt collector.
  3. The cyclone shroud can be washed in cold water with a mild detergent. Make sure it is completely dry before replacing.
  4. Replace the cyclone shroud by sliding it over the bottom of the secondary cyclone dirt collector and lining it up with the lock/ unlock arrow before twisting anti-clockwise until you feel a click.
  5. Replace the dirt cup and twist clockwise to lock.

Clearing clogs from the dirt cup

  1. Unplug the vacuum from electrical outlet.
  2. Remove the dirt cup from the vacuum, following steps 1-3 of Emptying the dirt cup on page 6.
  3. Remove the dirt cup filter assembly from the dirt cup, following step 2 of Clean the dirt cup filter on page 6.
  4. Tap the dirt cup filter assembly over a garbage container to remove any dirt or debris from the cyclone screen that surrounds the dirt cup filter.
  5. Reach up into the dirt cup to clear any dirt or debris from the dirt cup.
  6. Check to see if there are any clogs in the suction inlet.
  7. After clearing any dirt or debris from the dirt cup, replace the dirt cup filter assembly back in the dirt cup following step 8 of Cleaning the dirt cup filter on page 6.

Removing debris from turbine hard floor tool

  1. Use coin or flathead screwdriver to release the lock on the bottom of the tool to release the soft dusting brush.
  2. Return the brush and replace the locking mechanism when completed.

Troubleshooting

WARNING

To reduce the risk of electric shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks.

Please do not return this product to the store. 

Other maintenance or service not included in the manual should be performed by an authorized service representative.

Thank you for selecting a BISSELL product.

For any questions or concerns, BISSELL is happy to be of service. Contact us directly at 1-800-237-7691.

Replacement Parts

These items are available for your BISSELL vacuum.

Call 1-800-237-7691 or visit www.bissell.com

Service

If your BISSELL product should require service:Visit BISSELL.com or contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care.

Website or E-mail:www.BISSELL.com

Or Call:BISSELL Consumer Care1-800-237-7691Monday – Friday 8am – 10pm ETSaturday 9am – 8pm ETSunday 10am – 7pm ET

Bissell 1547 Series Hard Floor Expert Multi Cyclonic User Guide – Bissell 1547 Series Hard Floor Expert Multi Cyclonic User Guide –

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , ,