PET HAIR ERASER® TURBO PRO
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM.Always connect to a polarized outlet (one slot is wider than the other). Unplug from outlet when not in use and before conducting maintenance. When using an electrical appliance, basic precautions should be observed, including the following:
WARNINGTO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:» Do not leave vacuum cleaner when it is plugged in. Unplug from outlet when not in use and before servicing.» Do not use outdoors or on wet surfaces.» Do not allow to be used as a toy. Close attention is necessary when used by or near children.» Do not use for any purpose other than described in this User’s Guide. Use only the manufacturer’s recommended attachments.» Do not use with damaged cord or plug. If the appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.» Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep the cord away from heated surfaces.» Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.» Do not handle plug or vacuum cleaner with wet hands.» Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce airflow.» Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.» Turn off all controls before plugging or unplugging vacuum cleaner.» Use extra care when cleaning on stairs.» Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.» Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint, paint thinner, some mothproofing substances, flammable dust, or other explosive or toxic vapors.» Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).» Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.» Do not use without filters in place.» Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.» Use only on dry, indoor surfaces.» Keep appliance on a level surface.» Do not carry the vacuum cleaner while it is running.» Unplug before connecting or disconnecting the TurboBrush® Tool.
SAVE THESE INSTRUCTIONS
This model is for household use only.WARNING» Plastic film can be dangerous. To avoid the danger of suffocation, keep away from children.» Do not plug in your vacuum cleaner UNTIL you are familiar with all instructions and operating procedures.» To reduce the risk of electrical shock, turn the power switch OFF and disconnect polarized plug from electrical outlet BEFORE performing maintenance or troubleshooting checks.
Quick Start Guide
READ COMPLETE USER GUIDE FOR FULL INSTRUCTIONS ON USE, MAINTENANCE, AND IMPORTANT SAFETY NOTICES.
Assembly
Slide end of the wand into the top of the base. It will “click” when inserted correctly.
Attach Stretch Hose by lining the tabs on the cuff with the notches on the back of the vacuum. Twist clockwise to lock hose into place.
Remove Dirt Tank. Press the Dirt Tank Release Button and pull away from the vacuum.
Attach the end of the hose to vacuum by sliding square cuff into the bracket below the power switch.
Place the Dirt Tank on the vacuum by securing the bottom in place first, then pushing back until you hear a “click”.Install Optional Febreze® Filter
Press the Dirt Tank Release Button and pull away from the vacuum.
Twist tank cover to the unlock position then pulls up on the handle.
Remove the Pre-Motor Filter and replace it with the Febreze® Filter.Febreze and related trademarks are owned by The Procter & Gamble Company, Cincinnati, Ohio, and used under license by BISSELL Homecare, Inc.Thanks for buying a BISSELL vacuum!We love to clean and we’re excited to share one of our new innovative products with you. We want to make sure your vacuum works as well in five years as it does today, so this guide has tips on using (pages 6-9), maintaining (pages 10-13), and if there is a problem, troubleshooting (page 14).
What’s in the Box?
NOTE: Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap.
Product View
*NOTE: Pet TurboEraser® Tool and Pet Hair Eraser® Tool do not store on unit.THIS APPLIANCE HAS A POLARIZED PLUG
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plugin anyway.
Operations
WARNING Do not plug in your vacuum until you are familiar with all instructions and operating procedures.
Turn vacuum ON by pressing Power Switch on (I – ON and O – OFF). Press the Brush Roll switch to run the PowerBrush for the carpet cleaning (Brush Roll is on when the light on the switch is illuminated). See page 15 to maintain the Brush Roll.
Step gently on base and pull back on the handle to recline.
NOTE: The Brush Roll will automatically shut off when the vacuum is locked in an upright position. Recline to reactivate.NOTE: In the unlikely event that hair wrapped around your Brush Roll, run vacuum back and forth on the clean carpet several times to help release any wrapped hair.NOTE: Turn off the Brush Roll when vacuuming hard or delicate surfaces that may be caught by the rotating brush. This could include hardwood, tiled floors, small area rugs, or frieze carpets that have long delicate fibers or threads.
Adjusting the Suction Control
Locate the Suction Control setting on the vacuum handle. Adjust Suction Control for plush carpet or low carpet for easy multi-surface cleaning.
Above Floor Cleaning
Clean hard-to-reach spaces with the Quick Release Extension Wand. Push the release button to remove and attach the desired tool.
If desired, the Stretch Hose can be removed from the Extension Wand. To do so, twist the hose from the back of the wand to remove it.
Attach the desired tool. Use the Pet TurboEraser® Tool for best results on stairs. Or use the 2-in-1 Pet Brush with soft, white bristles for sensitive/gentle surfaces and rubber nubs to pick up embedded pet hair.
When finished, replace the wand back on the vacuum by sliding it into place until you hear “click.”
Vacuum Motor Protection
An internal thermal protector has been designed into your vacuum to protect it from overheating. When the thermal protector activates, the main vacuum motor
will stop operating. The front lights will remain on, even though the motor turns off. If this happens, proceed as follows.
1 Turn vacuum OFF and unplug from the electrical outlet.2 Check for the source of the overheating problem (full Dirt Tank, dirty filters, or a clog) and fix it by following the maintenance instructions.3 When the motor cools for approximately 30 minutes, the thermal protector automatically resets and cleaning may continue. If the vacuum will not turn on or the thermal protector continues to activate, your vacuum may need servicing. Contact BISSELL Consumer Care.
NOTE: The thermal protector controls the main vacuum motor only, not the brush motor. If the thermal protector activates, the brush and lights will continue to operate normally; however, there will be no suction.
Remove/Empty Dirt Tank
WARNING To reduce the risk of electrical shock, turn the power switch OFF and disconnect the polarized plug from the electrical outlet before performing maintenance or troubleshooting checks.
The Dirt Tank is full. Time to empty!
Press the Tank Release Button and grab the handle to pull the Dirt Tank away from the vacuum.
Hold the Dirt Tank over a trash bin and press the Empty Button. Once emptied, snap the bottom back into place.
Return the Dirt Tank to the vacuum, securing the bottom in place first and then pushing back until you hear a “click.”WARNINGDo not operate vacuum with damp or wet filters. Allow components to dry before reassembling the Dirt Tank.WARNINGBefore using your vacuum, make sure that the Dirt Tank is in the locked position and that all filters, both pre-and post-filters, are in place. DO NOT operate your vacuum without these filters.
Clean/Replace Pre-Motor Filters
WARNINGTo reduce the risk of electrical shock, turn the power switch OFF and disconnect the polarized plug from the electrical outlet before performing maintenance or troubleshooting checks.WARNINGDo not operate vacuum with damp or wet filters. Allow components to dry before reassembling the dirt container.
Press the Dirt Tank Release Button and pull away from the vacuum.
Twist tank cover to the unlock position then pulls up on the handle.
Remove Pre-Motor Filter from top of Dirt Tank lid by pulling out.
Both Pre-Motor Felt and Foam Filters are washable. Clean with mild detergent, rinse and squeeze all excess water. Allow filters to dry completely before reinserting. Return Pre-Motor Filters to the top of the Dirt Tank, placing the thick Foam Filter in last.NOTE: Replace filters every 3 to 6 months. Visit BISSELL.com for filter replacements.NOTE: Washing may decrease the Febreze® odor eliminating scent.
Clean/Replace Post-Motor Filter
WARNINGTo reduce the risk of electrical shock, turn the power switch OFF and disconnect the polarized plug from the electrical outlet before performing maintenance or troubleshooting checks.WARNINGDo not operate vacuum with damp or wet filters. Allow components to dry before reassembling the Dirt Tank.
Press the Dirt Tank Release Button and pull Dirt Tank away from vacuum.
Pull tab up to access Post-Motor Filter.
Twist filter counter-clockwise to unlock and remove from the vacuum.
When reassembling, be sure to lock the filter back into place. The pleated filter may NOT be washed. If dust/debris accumulates, gently tap the filter on the inside of a trash container.NOTE: Replace filters every 3 to 6 months. Visit BISSELL.com for filter replacements.
Clean Inner Cyclone Separator
Hold the Dirt Tank over a trash container. Press the bottom release button to empty.
Twist Cyclone counterclockwise and pull down to remove from tank.
Tap separator against the inside of trash container and rinse under warm water, if necessary. Be sure to let it dry completely before placing back in Dirt Tank.
Maintain Pet TurboEraser® Tool
Twist gray collar counter-clockwise, until slot appears, and then separate faceplate.
Remove Brush Roll, Belt, and Paddle Wheel. Inspect for damages and replace if necessary.
To reassemble, align two clips on each end of the Paddle Wheel with a Belt on and pop back into place. Place Brush Roll with Belt back in. Faceplate will not close properly if all parts are not aligned correctly.
To put the faceplate back on, align the tabs in the top of the cover and place it down to “click” into place.
Replace Brush and Belt
Unplug and turn the vacuum over. Unscrew 10 Phillips-head screws to remove the bottom cover.
Pull Brush Roll straight out and slide Belt off motor gear. Replace Brush Roll and/or Belt.
Inspect Brush Roll by placing it on its end and spin. The Brush Roll should spin freely, multiple times by one flick. If it doesn’t, replace Brush Roll. Inspect Belt, replace if it appears damaged.
1. Place Belt back on Brush Roll.2. Pinch Belt around Brush Roll & hook back around the motor gear.3. Rotate Brush Roll into place and line up end caps.4. Re-attach the bottom cover with 10 screws.NOTE: If an object becomes lodged in the foot and the brush shuts off, turn the vacuum off and unplug from the electrical outlet. Remove obstruction and brush will automatically reset when the vacuum is plugged and turned back on.
Parts & SuppliesFor Parts and Supplies, go to www.BISSELL.com and enter your model number in the search field.
Troubleshooting
WARNING To reduce the risk of electric shock, turn power switch OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.
|
Problem |
Possible causes |
Remedies |
| Brush Roll doesn’t rotate | Brush Roll switch is turned OFF. | Make sure Brush Roll switch is ON. |
| Vacuum is locked in upright position. | Recline vacuum and switch on the Brush Roll. | |
| Vacuuming on Premium Soft Carpet. | Adjust Suction Control to reduce suction on softer carpets. | |
| Brush Roll has lodged debris or other entanglements, keeping the brush from rotating. | Unplug to reset brush motor, checking for and removing debris before turning ON. | |
| Vacuum won’t pick up dirt | The filters are dirty. | Remove and rinse Pre-Motor Filters. Allow enough time for them to dry properly before reinserting. Remove and dust off post- motor filter. |
| There is a clog in the vacuum. | Remove bottom cover and check for any buildup of debris. Remove debris and debris buildup before reinstalling bottom cover. | |
| Dirt Tank is not seated
correctly. |
Press the Tank Release to release the
Dirt Tank and reseat properly. |
|
| There is a crack or hole in the Main Hose. | If there is a crack or hole, order a new Main Hose from the BISSELL website. | |
| Main Hose is not connected. | Locate the Main Hose and reconnect by pushing the hose connection. | |
| There is a clog in the hose. | Disconnect Lower Hose and check for clogs as well. Use a broom handle to push any debris out. | |
| Hair wrapped around Brush Roll | Run vacuum back and forth on clean carpet several times to release wrapped hair. | |
| Dirt is escaping from the vacuum | Dirt Tank is full. | Empty the Dirt Tank. |
| Filters are missing or dirty. | Check to see if all of the Pre-Motor and Post-Motor Filters are in place and clean | |
| Hose won’t pick up dirt | Suction is set too low. | Adjust using the Suction Control Feature. |
| Vacuum is hard to push or pul | Suction is set too high. | Adjust using the Suction Control Feature. |
| High-pitched Noise | There is a clog in the vacuum. | Check inside of Main Hose and Lower Hose for clogs by disconnecting from vacuums. |
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Care by E-mail, telephone, or regular mail as described below.
Limited Five-Year WarrantySubject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL will repair or replace (with new, refurbished, lightly used, or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for five years, any defective or malfunctioning part. See information below on “If your BISSELL product should require service.” This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User’s Guide is not covered.
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES, EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE FIVE-YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you.
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim.
Service
If your BISSELL product should require service:Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area. If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care.
Website: www.BISSELL.comE-mail: www.BISSELL.com/email-usCall: BISSELL Consumer Care1-800-237-7691Monday – Friday 8am – 10pm ETSaturday 9am – 8pm ETSunday 10am – 7pm ETPlease do not return this product to the store.Other maintenance or service not included in the manual should be performed by an authorized service representative.For any questions or concerns, BISSELL is happy to be of service. Contact us directly at 1-800-237-7691.
Register your product today!
Registering is quick, easy, and offers you benefits over the lifetime of your product. You’ll receive:
BISSELL Rewards PointsAutomatically earn points for discounts and free shipping on future purchases.Faster ServiceSupplying your information now saves you time should you need to contact us with questions regarding your product.Product Support Reminders and AlertsWe’ll contact you with any important product maintenance reminders and alerts.Special PromotionsOptional: Register your email to receive notice of offers, contests, cleaning tips, and more!Visit www.BISSELL.com/registration!Visit the BISSELL website: www.BISSELL.comWhen contacting BISSELL, have the model number of cleaners available.Please record your Model Number: ___________________Please record your Purchase Date: ___________________NOTE: Please keep your original sales receipt. It provides proof of purchase date in the event of a warranty claim. See the Warranty page for details.
Parts & SuppliesFor Parts and Supplies, go to www.BISSELL.com and enter your model number in the search field.
We can’t wait to hear from you!Rate this product and let us (and millions of your closest friends) know what you think! www.BISSELL.com
©2018 BISSELL Homecare, IncGrand Rapids, MichiganAll rights reserved. Printed in ChinaPart Number 161-5718 04/18Visit our website at www.BISSELL.com
Bissell 2281K Series Turbo Pro Lightweight and Powerful Pet Hair Eraser Quick Start/ User Guide – Bissell 2281K Series Turbo Pro Lightweight and Powerful Pet Hair Eraser Quick Start/ User Guide –
[xyz-ips snippet=”download-snippet”]