BLAUPUNKT 12v Vehicle Lighting Led Headlamp Installation Guide

Table of Contents

BLAUPUNKT 12v Vehicle Lighting Led Headlamp

CAUTIONS

Safety NotesThis product has been manufactured according to established safety guidelines. However, dangers may still occur if the safety notes in this manual are not observed. This manual is intended to familiarize the user with the product’s important functions. Read this carefully, prior to installing the product. Keep this manual in an easily accessible location. In addition, do observe the instructions of the devices used in conjunction with the product.

General Safety

A headlamp is intended for installation and operation in a vehicle with 12V vehicle system voltage and can be used in headlights with H4 halogen lamps.
Ensure the headlamp does not have defects before installation.
Keep the headlamp away from children.
Keep the headlamp away from flammable areas or liquids.
The headlamp should be stored in a dry and low humidity place.
Avoid skin contact with the high temperature/ working headlamp when replacing the headlamp. Allow the headlamp to drop to room temperature before replacing the headlight.
Do not modify the product, or expose the product to dust, grease stains, or scratch the surface of the headlamp.
Do not look directly at the operating headlamp, it may cause eye damage.
After installation, ensure below are working correctly1. Correct light/beam pattern2. Indicators are working3. Wiring are connected correctly4. Covers are installed back to the car correctlyThis manual may be updated from time to time without any notice.

DisclaimerIn no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products. USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on an as-is basis. No warranty, whether expressed or implied is provided in the U.S. or Canada.

STRUCTURE & FUNCTIONS

Applicable to: Reflector headlightProduct Name : 134250W (5000K), 134260W (6000K)Technology : LEDPower : 26W±10%, 26W±10%Operating Voltage : 13.2VLuminous Flux : 2100lm ±20%, 1900lm ±20%Water Resistant Rating : IP65Lifespan : 3000 hourColour Temperature : 5000K & 6000KBase : P43t

Applicable to : Projector, reflector & fog headlight Product Name : 197250W (5000K), 197260W (6000K) Technology : LEDPower: 26W±10%Operating Voltage : 13.2VLuminous Flux : 2300lm ±20%Water Resistant Rating : IP65Lifespan : 3000 hourColour Temperature : 5000K & 6000KBase : PX26D

Applicable to : Projector, reflector & fog headlight Product Name : 136650W (5000K), 136660W (6000K) Technology : LEDPower: 26W±10%Operating Voltage : 13.2VLuminous Flux : 2300lm ±20%Water Resistant Rating : IP65Lifespan : 3000 hourColour Temperature : 5000K & 6000KBase : PGJ19-1/2/3/5

SPECIFICATIONS

Applicable to : Projector, reflector & fog headlight Product Name : 100650W (5000K), 100660W (6000K) Technology : LEDPower : 26W±10%Operating Voltage : 13.2VLuminous Flux : 2300lm ±20%Water Resistant Rating : IP65Lifespan : 3000 hourColour Temperature : 5000K & 6000KBase : P22D

Applicable to : Projector & reflector headlight Product Name : 101250W (5000K), 101260W (6000K) Technology : LEDPower : 26W±10%Operating Voltage : 13.2VLuminous Flux : 2300lm ±20%Water Resistant Rating : IP65Lifespan : 3000 hourColour Temperature : 5000K & 6000KBase : PX22D

TROUBLESHOOTING

If any of the following problems occur, please resort to Troubleshooting for possible solutions. Consult Blaupunkt authorized dealer if the problem persists.

PRE-INSTALLATION

1. Open the hood of the vehicle.2. Find the installed location of the original halogen bulb.

3. Remove the halogen bulb from the headlight housing.

INSTALLATION INSTRUCTION

1. Remove the cap plate from the headlamp.2. Insert the cap plate and secure it with the retaining spring clip.

3. Install the headlamp into headlight housing and turn clockwise to secure it.

4. Please ensure the diodes (LED chips) of the headlamp are in a side to side orientation. Correct Alignment

5. Connect the headlamp cable to the vehicle wiring harness.

A warning canceller adaptor may be needed in case of the warning signal light up after installation.
Remove bulb, turn it 180° & reinstall in case bulb does not light up.
Fit for 12V vehicle only.