BLAUPUNKT BLP0232-001 Wireless charger User Manual

User manualWireless charger|BLP0232-001

 

ENJOY IT 

Safety instructions

Read these safety instructions before using your device and store them for possible future reference.

  • The charger is not intended for use by persons (including children) with reduced physical, sensory or mental capacity. Persons who have not read the manual, unless they have received explanations by a person responsible for their safety and supervision should not use this unit.
  • Children should be monitored to ensure that they do not play with the charger.
  • The charger should always be readily accessible.
  • The device should not be exposed to dripping or splashing water.
  • No objects filled with liquids such as vases shall be placed on the device.
  • Always leave a minimum distance of 10 cm around the unit to ensure sufficient ventilation.
  • Open flame sources, such as candles, should not be placed on top of the device.
  • The device is intended for use only in a temperate climate.
  • The product should not be exposed to excessive heat such as sunshine, fire or similar.

SWITCH OFF IN RESTRICTED AREAS

Switch the device off where the use of the device is not allowed or where there is a risk of causing interference or danger, for example onboard an aircraft, near medical equipment, fuel, chemicals or blasting sites.

INTERFERENCE

All wireless devices are susceptible to interference which may affect their performance.All our devices conform to international standards and regulations, and if need be national ones, with a view to limiting user exposure to electromagnetic fields. These standards and regulations were adopted after the completion of extensive scientific research. This research established no link between the use of the mobile headset and any adverse effects on health if the device is used in accordance with standard practices.

Specification parameter

Rated voltage: DC 5V 1AInput: 5V 2AOutput Power: Wireless 5WUSB Output: DC 5V 1ASize: 90x90x9mmMaterial: Wheat strawCompatible with the QI standard.

Power supply:The charger is recommended to power by a qualified AC adapter.

Operation:Connect the wireless charger to an outlet such as a qualified Ac-Adapter, then a LED-Light shine.Put your phone on the charging plate and the battery starts to charge, the LED-Light blinks during charging. If the phone doesn’t start to charge, please try to reposition it.

Troubleshooting

The indicator off

  1.  Please change a power cable try again
  2.  Please change the AC Adapter (5V 1A or 5V 2A adapter)

When the indicator flashes, but Phone can’t charge.

  1.  Please check whether your phone supports Qi wireless charging
  2.  Please remove the phone case
  3.  Put the phone in the center of the wireless charger
  4.  Please adjust the orientation of the phone, horizontal and vertical
  5.  Please take off the phone restart the device and put the phone in the charger center
  6.  Please try to replace the 5V 1A or 5V2A AC adapter.

Phone charging intermittently

  1.  Please remove the phone case.
  2.  Put the phone in the center of the wireless charger
  3.  Please try to replace the 5V1A or 5V2A AC adapter.

The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old ppliances must be collected separately in order to optimize the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed-out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected.

Imported by Dag Technologie®79/81 Ancienne route Nationale 769570 DardillyFrancewww.blaupunkt.com

Dag Technologie®79/81 Ancienne Route Nationale 769570 Dardilly – FranceAll rights reserved. All brand names are registered trademarks of their respective owners. Specifications are subject to change without prior

References

[xyz-ips snippet=”download-snippet”]


Posted

in

by