boxis 8-Sheet NanoShred shredder User Manual

8-Sheet NanoShred shredderUser Manual

The NANOCUT® AssuranceYour letter-sized document will be shreddedinto over 3,000 virtually unreadable particles.

ULTRA HIGH LEVEL SECURITY

This Boxis® NanoShred® will render your most sensitive documents into virtually unreadable particles! This shredder offers an ultra high security level shredding in a personal sized machine. The Boxis® NanoShred® will turn a letter-size document into at least 3,000 particles.Just imagine the peace of mind knowing that your shredded documents will never be deciphered!

MAXIMIZE BIN CAPACITY

One of the advantages of the nanocut® shred size is the ability to maximize the space in the waste bin. The nanocut® particles will fill your waste bin more densely thereby optimizing the bin capacity.

LESS IS MORE PRODUCTIVITY

With the Boxis® NanoShred®, you will have less bulk in your trash! Compared to comparable crosscut or microcut shredders, the Boxis® NanoShred® can shred a lot more documents before you have to empty the bin. Shred more and empty less.

Product Diagram

WARNINGS

CAUTION: KEEP THIS DEVICE AWAY FROM CHILDREN AND PETS!Place the paper shredder in an area less accessible to children.

  • DO NOT PLACE FINGERS TOO CLOSE TO THE FEED SLOT AS SERIOUS INJURY MAY OCCUR. Paper shredders can pull children’s fingers into the shredder mechanism.
  • AVOID GETTING LOOSE CLOTHING OR JEWELRY NEAR THE FEED SLOT.
  • AVOID GETTING HAIR NEAR THE FEED SLOT.
  • NEVER spray any aerosol-based products in or around the shredder.
  • NEVER dispose of flammable chemicals, or materials that have come into contact with flammable chemicals (for example, nail polish, acetone, gasoline) in the shredder basket. NEVER use any petroleum based or flammable oils or lubricants in or around the machine, as some oils can combust causing serious injury. Lubricants specifically designed for shredders are acceptable.
  • NEVER place the shredder near water or any heat source.
  • Avoid direct contact with water

STOP USE IMMEDIATELY IF:

  • The shredder blades become jammed with paper.
  • The shredder motor makes loud and/or irregular noises during operation.
  • The shredder blades or paper guides become bent or compromised in any way.
  • Continuing to operate your shredder with any of the above conditions present could be potentially dangerous.

Installation

  • Only operate this product from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult an electrician.
  • Make sure the electrical outlet is easily accessible from the shredder.
  • Shredder must be operated only in upright position.
  • To make sure the shredder has proper ventilation, place it a minimum distance of 2 in. (5 cm) from the wall or furniture.

Safety Instructions

  1. Read and follow all instructions before use. Save these instructions for later use.
  2. Always turn off and unplug the machine before moving, servicing, cleaning, or anything other than normal operation. Serious injury may result. Clean shredder with a damp cloth, using a mild soap and water solution.
  3. Do not use abrasives or petroleum-based cleaners.
  4. Place this product as close as possible to power source for quick and easy unplugging.
  5. Turn off the power switch before removing waste bin. It is advisable to disconnect the power cord before opening the shredder.
  6. This product should never be placed near a radiator or other heat source.
  7. Do not allow anything to rest on the power cord. Do not place the power cord where people may walk on it.
  8. If an extension cord is used with this product, make sure the total ampere (amps) ratings on the products plugged into the extension cord do not exceed the extension cord’s ampere rating.
  9. The machine contains no serviceable parts. Do not attempt to service this product yourself, as opening or removing covers may expose you to risk of injury.The manufacturer disclaims all liability for injuries resulting from opening the machine. Mechanical damage resulting from opening the machine may void the warranty.
  10. Unplug this product and contact technical support when:•  The power cord or plug is damaged or frayed.•  Liquid has been spilled on the product.•  The product has been exposed to rain.•  The product does not operate normally, even when the operating instructionsare followed.•  The product has been dropped, or the casing has been damaged.
  11. This shredder should be operated only with an operator in attendance.
  12.  Empty the waste bin regularly so that the waste output is not impeded.
  13. This machine can shred normal paper and credit cards. However, you should shred only one type of these items at a time to avoid causing an overload.

Technical Specifications

  • Cutting Type: Nanocut®
  • Shred Size.: .0.08 x 0.39 in. (2 x 10mm)
  • Will Shred: Paper ONLY
  • Continuous Operation: .2 minutes
  • Cool Down Time: 30 minutes
  • Bin Size: 3.04 gallons (11.5 liters)
  • Unit Dimensions: 14.25 x 7.68 x 15.04 inches (362 x 195 x 382 mm)
  • Unit Weight: 12.57 lbs (5.7kg)

Assembly

NOTE: This shredder will operate only when used with the supplied basket. The supplied basket has a built-in safety feature which prevents the shredder from operating if used with any other basket or if improperly assembled.

This shredder contains sharp edges on the underside of the shredder head.The plug on the power supply cord is intended to serve as the disconnect device, so the socket-outlet should be installed near the equipment and should be easily accessible.

Setup

  1. Place the machine on level ground and plug the power cord into any easily reached grounded electrical outlet.
  2. Make sure the wastebasket is correctly positioned.
  3. Connect the power cord to any standard 120 volt AC outlet. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.
  4. Slide the switch to ON position.
  5. Insert paper to activate.

Paper Clips and Staples:

IMPORTANT ! This shredder should NEVER shred anything made of metal:staples, small paperclips, industrial or non-standard size staples, jumbo and/ or butterfly paperclips, or binder clips. ONLY paper can be inserted to be shredded, otherwise damage will be caused to the blades.

Cautions:

  1. All shredders have very sharp, exposed blades on the underside. Please use care when mounting the shredder on to the wastebasket.
  2. Make sure power cord is not damaged in any way and that the outlet is properly functioning.
  3. It is normal for residual lubricant in the motor to burn off during the first several extended uses of your shredder. Should you notice a slight burning odor or the presence of small wisps of smoke during the first several extended uses, you may continue using the shredder. If either symptom continues to occur after repeated use, please contact technical support for assistance.

Operation

Please read operating instructions before using shredder. Check machine for damage or defect; remnants of paper particles found in the waste bin are normal due to product testing.

Clearing a Jam

If paper is not inserted properly into the shredder, or if the sheet capacity is exceeded, a jam may result. Move the switch to the REVERSE (<<) position, and remove the excess paper from the top and pull it out. TO PREVENT ANY INJURIES, DO NOT PLACE YOUR HANDS NEAR THE FEED OPENING. Once the paper is cleared, normal shredding operation can resume. If the shredder jams while in reverse, press the switch to the AUTO position and let shredder run to clear the jammed paper. If jam does not clear, slide the switch back and forth between the REV and AUTO until the jam is cleared. If the jam cannot be cleared following this procedure, unplug the unit and carefully remove the jammed paper manually.

Overheating

If your shredder overheats, the unit will automatically shut off and all functions will cease in order to protect the motor. Turn off and unplug the shredder from the outlet. Allow enough time for the motor to cool down. The shredder will not resume normal function until the temperature of the motor cools down to a safe temperature. Once cool, plug the shredder back into the outlet, turn the unit back on and resume normal operation. Make sure to empty waste basket to avoid overloading the basket and damaging the cutting mechanism.

Bin Full:

  1. Turn the unit OFF by sliding to the Power Off position.
  2. Remove the bin and either dispose of the paper shreds or compress the shreds down.
  3.  Re-insert the bin into the housing.
  4. Slide the power switch to Power On to resume normal operation.

Overload:

If too much paper is inserted into either the manual feed or auto feed the unit will automatically stop shredding. When this occurs, slide the switch to Manual Reverse to dislodge the jammed paper. Remove the paper, recount the pages, and continue with no more than the maximum stated capacity.

Maintenance:

Apply lubricant after 30 minutes of shredding or a minimum of twice per month. Only shredder lubricant sheets or bottled lubricant designed specifically for shredders should be used. Follow the instructions provided with the shredder lubricant. NEVER USE AN AEROSOL LUBRICANT, or any lubricant that is flammable. Refer to the warnings provided in this shredder manual.

One Year Limited Warranty

The manufacturer warrants the machine for a period of one year to be free from defects in material and workmanship; this warranty does NOT cover normal wear and tear. If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at the manufacturer’s option and expense, of the defective part except for the shipping cost. It is the responsibility of the consumer to pay the shipping costs to return the machine to the manufacturer. This warranty is valid for the original consumer only with original proof of purchase and is not transferable. This warranty does not apply in cases of abuse, mishandling or unauthorized repair. The machine contains no serviceable parts. Do not attempt to service this product yourself, as opening or removing covers may expose you to risk of injury. The manufacturer disclaims all liability for injuries resulting from opening the machine. Mechanical damage resulting from opening the machine may void the warranty.

ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE. In no event shall the manufacturer be liable for any consequential or incidental damages attributable to this product. This warranty gives you specific legal rights. You may have other legal rights that vary according to the laws of each territory.

Repairs must be performed by the manufacturer’s authorized technician. For more details, or to obtain service under this warranty, please contact us at 866-707-1854. Please retain original proof of purchase to ensure that your product is recorded and warranty information received.

Return Instructions:Call 866-707-1854 for a Return Authorization Number (RA#) in order to return adefective product.

Product Registration:Please register your new product by calling 866-707-1854.

Contact Us:

For more information, please call 866-707-1854, or email us at

We have taken the lead in the next evolution of paper shredderstoward enhanced security and productivity.

The next evolution of paper shreddersWe have taken the lead in the next evolution of paper shredderstoward enhanced security and productivity.Toll-Free 866.707.1854 | www.boxisshredder.comAn INTEK Brand | We Care. We Share. ©2020 INTEK America Inc.18528 S. Dominguez Hills Drive, Rancho Dominguez, CA 90220

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,